{"product_id":"old-masters-armor-interior-water-based-finish-flat-quart","title":"Old Masters Armor Interior Water-Based Finish, Flat, Quart","description":"\u003cp\u003e\u003cstrong\u003eOld Masters Armor Interior Water-Based Finish, Flat, Quart\u003c\/strong\u003e is intended for interior use. \u003c\/p\u003e\n\u003ch3\u003eFeatures\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eClear finish\u003c\/li\u003e\n\u003cli\u003eSelf-sealing\u003c\/li\u003e\n\u003cli\u003ePart B hardener option for floors\u003c\/li\u003e\n\u003cli\u003eDries clear with slight wood amber effect over white or pastel coatings\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eBest for\u003c\/h3\u003e\u003cp\u003eWood floors; Cabinets; Furniture; Woodwork; Previously finished surfaces after sanding; Fully dry stained surfaces\u003c\/p\u003e\u003ch3\u003eSpecs\u003c\/h3\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003eColor or finish\u003c\/th\u003e\n\u003ctd\u003eClear\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSheen\u003c\/th\u003e\n\u003ctd\u003eFlat\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSelected size\u003c\/th\u003e\n\u003ctd\u003eQuart\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBase\u003c\/th\u003e\n\u003ctd\u003ewater\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eUse\u003c\/th\u003e\n\u003ctd\u003einterior\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoverage\u003c\/th\u003e\n\u003ctd\u003eApproximately 300 to 400 sq ft\/gal at 3 to 5 wet mils\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eTouch dry\u003c\/th\u003e\n\u003ctd\u003eWithin 30 minutes at 70°F and 50% RH\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRecoat\u003c\/th\u003e\n\u003ctd\u003e1 to 2 hours; dry-time paragraph says ready after 1 hour at 70°F and 50% RH\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFull cure\u003c\/th\u003e\n\u003ctd\u003eCuring to ultimate hardness during first week; light use after 24 hours\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApplication conditions\u003c\/th\u003e\n\u003ctd\u003eAir and surface 60°F to 90°F; humidity 30% to 70%\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoats\u003c\/th\u003e\n\u003ctd\u003eThree\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply with\u003c\/th\u003e\n\u003ctd\u003eSynthetic fiber brush; Foam brush; Flat pad; Sprayer; Lambswool applicator for large flat areas\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThinning\u003c\/th\u003e\n\u003ctd\u003eNot recommended; if needed add small amount of water, up to 8 oz for spray application\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCleanup\u003c\/th\u003e\n\u003ctd\u003eWarm soapy water; rinse clean\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVOC\u003c\/th\u003e\n\u003ctd\u003eTDS: less than 275 g\/L; see notes for variant SDS value\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eTopcoat compatibility\u003c\/th\u003e\n\u003ctd\u003eSelf-sealing; test over paints and stains; Masters Armor Part B Hardener may be added for floors, one 4 oz container per gallon\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eManufacturer part #\u003c\/th\u003e\n\u003ctd\u003e72004\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch3\u003eHow to apply\u003c\/h3\u003e\u003cp\u003eStart with the manufacturer's preparation steps: Clean and dry; remove dirt, wax, grease, glue and other contaminants; Sand new wood from medium to fine grit with grain; remove dust; Sand previously finished surfaces with 220 grit to remove gloss and imperfections; Allow oil-based stain at least 48 hours drying before topcoating; Do not use steel wool or tack rag.\u003c\/p\u003e\u003col\u003e\n\u003cli\u003ePrepare surface and remove sanding dust\u003c\/li\u003e\n\u003cli\u003eStir thoroughly; do not shake; test adhesion\u003c\/li\u003e\n\u003cli\u003eApply full even coats with grain at 3 to 5 wet mils\u003c\/li\u003e\n\u003cli\u003eWait 1 to 2 hours; lightly sand with 220 grit and remove dust\u003c\/li\u003e\n\u003cli\u003eReapply for three coats total\u003c\/li\u003e\n\u003c\/ol\u003e\u003ch3\u003eGood to know\u003c\/h3\u003e\u003cp\u003eUse limits: Over shellac, lacquer, or fillers, stains, or sealers containing stearates; Over sanding sealer on floors.\u003c\/p\u003e\u003cp\u003e: Not considered hazardous under OSHA Hazard Communication Standard 2024\u003c\/p\u003e\u003cp\u003eKeep the recoat time and full cure time separate when planning the project. The recoat figure tells you when another coat can be applied; it does not replace the full cure guidance.\u003c\/p\u003e\u003ch3\u003eQuestions\u003c\/h3\u003e\u003ch4\u003eHow much will I need?\u003c\/h4\u003e\u003cp\u003eUse these manufacturer coverage figures: Approximately 300 to 400 sq ft\/gal at 3 to 5 wet mils. Match the figure to the container size, and account for the stated number of coats.\u003c\/p\u003e\u003ch4\u003eWhen can I apply another coat?\u003c\/h4\u003e\u003cp\u003eThe listed manufacturer recoat guidance is 1 to 2 hours; dry-time paragraph says ready after 1 hour at 70°F and 50% RH. Follow the application conditions and instructions for this product.\u003c\/p\u003e\u003cp\u003e\u003ca href=\"https:\/\/myoldmasters.com\/product\/masters-armor\" target=\"_blank\" rel=\"noopener\"\u003eManufacturer directions and product information\u003c\/a\u003e\u003c\/p\u003e","brand":"Old Masters","offers":[{"title":"Default Title","offer_id":67673296470326,"sku":"72004","price":26.6,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0931\/9750\/0726\/files\/086348720046.jpg?v=1791582861","url":"https:\/\/projectweekenddiy.com\/products\/old-masters-armor-interior-water-based-finish-flat-quart","provider":"Project Weekend DIY","version":"1.0","type":"link"}