{"title":"Pre-Stain Wood Conditioner for Pine, Maple and Birch","description":"\u003cdiv class=\"collection-intro\"\u003e\n\u003cp\u003ePre-stain wood conditioner goes on bare wood before stain so the color soaks in evenly instead of turning blotchy or streaky. Soft and porous woods take stain unevenly, and the makers name the same suspects again and again: pine, fir, alder, aspen, birch, maple, poplar and cherry. This page lines up every conditioner we carry from Minwax, Varathane, General Finishes and Old Masters with the wait time before staining, the coverage and the stain type each one is made for, taken from the maker sheets.\u003c\/p\u003e\n\u003cp\u003eThe one rule that matters most: match the conditioner to your stain. Oil-based conditioners from \u003ca href=\"\/products\/minwax-pre-stain-wood-conditioner-clear-quart\"\u003eMinwax\u003c\/a\u003e, \u003ca href=\"\/products\/varathane-premium-wood-conditioner-clear-quart\"\u003eVarathane\u003c\/a\u003e and \u003ca href=\"\/products\/general-finishes-oil-based-pre-stain-wood-conditioner-natural-quart\"\u003eGeneral Finishes\u003c\/a\u003e go under oil-based stain. The \u003ca href=\"\/products\/general-finishes-pre-stain-conditioner-natural-pint\"\u003eGeneral Finishes water-based Pre-Stain Conditioner\u003c\/a\u003e goes under water-based stain. \u003ca href=\"\/products\/old-masters-low-voc-wood-conditioner-quart\"\u003eOld Masters Low VOC Wood Conditioner\u003c\/a\u003e lists a wait time for both oil-based and water-based stain.\u003c\/p\u003e\n\u003ch2\u003eCompare pre-stain wood conditioners\u003c\/h2\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eConditioner\u003c\/th\u003e\n\u003cth\u003eUse under (maker)\u003c\/th\u003e\n\u003cth\u003eWait before staining (maker)\u003c\/th\u003e\n\u003cth\u003eCoverage (maker)\u003c\/th\u003e\n\u003cth\u003eNotes (maker)\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eMinwax Pre-Stain Wood Conditioner (\u003ca href=\"\/products\/minwax-pre-stain-wood-conditioner-clear-half-pint\"\u003ehalf pint\u003c\/a\u003e, \u003ca href=\"\/products\/minwax-pre-stain-wood-conditioner-clear-quart\"\u003equart\u003c\/a\u003e, \u003ca href=\"\/products\/minwax-pre-stain-wood-conditioner-clear-gallon\"\u003egallon\u003c\/a\u003e)\u003c\/td\u003e\n\u003ctd\u003eOil-based stains such as Minwax Wood Finish, Gel Stain and PolyShades\u003c\/td\u003e\n\u003ctd\u003eLet it penetrate 5 to 15 minutes and wipe off the excess; stain after about 15 minutes and within 2 hours (on alder, Minwax suggests waiting 2 hours)\u003c\/td\u003e\n\u003ctd\u003eAbout 100 to 125 sq ft per quart\u003c\/td\u003e\n\u003ctd\u003eMade for pine, fir, alder, aspen, birch and maple. Not for use under water-based stains. Can lighten the color on hardwoods\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eVarathane Premium Wood Conditioner (\u003ca href=\"\/products\/varathane-premium-wood-conditioner-clear-half-pint\"\u003ehalf pint\u003c\/a\u003e, \u003ca href=\"\/products\/varathane-premium-wood-conditioner-clear-quart\"\u003equart\u003c\/a\u003e, \u003ca href=\"\/products\/varathane-premium-wood-conditioner-clear-gallon\"\u003egallon\u003c\/a\u003e)\u003c\/td\u003e\n\u003ctd\u003eOil-based stain on interior wood\u003c\/td\u003e\n\u003ctd\u003eApply until the wood is saturated, wipe off the excess before it dries, then let it penetrate 30 minutes before staining\u003c\/td\u003e\n\u003ctd\u003e440 to 880 sq ft per gallon (110 to 220 sq ft per quart)\u003c\/td\u003e\n\u003ctd\u003eOil-based modified alkyd. Apply at 55 to 90 F with humidity under 85%. Not recommended with water-based stains (Varathane VAR-04)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/products\/general-finishes-oil-based-pre-stain-wood-conditioner-natural-quart\"\u003eGeneral Finishes Oil-Based Pre-Stain Wood Conditioner, quart\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003eOil-based stain\u003c\/td\u003e\n\u003ctd\u003eLet it penetrate at least 10 minutes and wipe the excess; apply oil-based stain after 30 minutes and no later than 2 hours\u003c\/td\u003e\n\u003ctd\u003e180 to 200 sq ft per quart\u003c\/td\u003e\n\u003ctd\u003eFor new soft and porous wood such as aspen, cherry, birch, poplar and pine. Dries with an amber cast. Do not thin\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eGeneral Finishes Water-Based Pre-Stain Conditioner (\u003ca href=\"\/products\/general-finishes-pre-stain-conditioner-natural-pint\"\u003epint\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-pre-stain-conditioner-natural-quart\"\u003equart\u003c\/a\u003e)\u003c\/td\u003e\n\u003ctd\u003eGeneral Finishes water-based stain\u003c\/td\u003e\n\u003ctd\u003eAbout 30 minutes in ideal conditions (about 70 F); check the can directions\u003c\/td\u003e\n\u003ctd\u003eAbout 50 to 75 sq ft per pint\u003c\/td\u003e\n\u003ctd\u003eFor maple, pine and cherry. Clear, not a Natural stain color. Conditioning can lighten the final color, so test the whole stain and topcoat process first. Soap and water cleanup\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOld Masters Low VOC Wood Conditioner (\u003ca href=\"\/products\/old-masters-low-voc-wood-conditioner-quart\"\u003equart\u003c\/a\u003e, \u003ca href=\"\/products\/old-masters-low-voc-wood-conditioner-gallon\"\u003egallon\u003c\/a\u003e)\u003c\/td\u003e\n\u003ctd\u003eOil-based or water-based stain\u003c\/td\u003e\n\u003ctd\u003eDry 8 hours before an oil-based stain, 24 hours before a water-based stain\u003c\/td\u003e\n\u003ctd\u003eAbout 400 to 500 sq ft per gallon\u003c\/td\u003e\n\u003ctd\u003eFor pine, fir, maple and poplar. VOC 100 g\/L\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch2\u003ePre-stain conditioner FAQ\u003c\/h2\u003e\n\u003ch3\u003eDo I need wood conditioner before staining?\u003c\/h3\u003e\n\u003cp\u003eOn soft or porous wood, yes. The makers list pine, fir, alder, aspen, birch, maple, poplar and cherry as the woods that blotch. Minwax suggests a fingernail test: if your nail dents a hidden spot, condition before you stain. On dense hardwoods such as oak you may not need it, and Minwax notes that conditioner can limit or lighten stain color on hardwoods, so try it on a scrap first.\u003c\/p\u003e\n\u003ch3\u003eOil-based or water-based conditioner?\u003c\/h3\u003e\n\u003cp\u003eMatch it to the stain. Minwax and Varathane say not to use their oil-based conditioners under water-based stain, and General Finishes makes separate oil-based and water-based versions. Old Masters Low VOC Wood Conditioner works under either one with a longer wait: 8 hours before oil-based stain and 24 hours before water-based stain.\u003c\/p\u003e\n\u003ch3\u003eHow long do I wait between conditioner and stain?\u003c\/h3\u003e\n\u003cp\u003eIt depends on the brand. Minwax: stain after about 15 minutes and within 2 hours. General Finishes oil-based: after 30 minutes and within 2 hours. Varathane: let it penetrate 30 minutes. General Finishes water-based: about 30 minutes. Old Masters: 8 hours for oil-based stain, 24 hours for water-based. Minwax and General Finishes oil-based both set a 2 hour limit, so plan to condition and stain in one session.\u003c\/p\u003e\n\u003ch3\u003eShould I use conditioner on pine or plywood?\u003c\/h3\u003e\n\u003cp\u003ePine is the wood every maker names first. Minwax puts plywood faced with pine, fir or birch in the same group, so condition it and test your stain on the back side or a scrap. Gel stain is another route on hard-to-stain wood: Old Masters positions its Gel Stain for even color on pine, poplar, maple, plywood and veneers. See \u003ca href=\"\/collections\/curated-wood-stains-gel-stains\"\u003ewood stains and gel stains\u003c\/a\u003e and \u003ca href=\"\/collections\/general-finishes-gel-stain\"\u003eGeneral Finishes gel stain\u003c\/a\u003e.\u003c\/p\u003e\n\u003ch3\u003eHow much conditioner do I need?\u003c\/h3\u003e\n\u003cp\u003eUse the maker coverage. A Minwax quart covers about 100 to 125 sq ft, a General Finishes oil-based quart about 180 to 200 sq ft, a Varathane quart 110 to 220 sq ft, a General Finishes water-based pint about 50 to 75 sq ft, and an Old Masters gallon about 400 to 500 sq ft. Plan on one coat; Minwax notes that very absorbent wood can take a second.\u003c\/p\u003e\n\u003ch3\u003eWhat goes on after the stain?\u003c\/h3\u003e\n\u003cp\u003eA clear topcoat. Follow the stain label for dry time, then choose from \u003ca href=\"\/collections\/polyurethane\"\u003epolyurethane for wood\u003c\/a\u003e, \u003ca href=\"\/collections\/spray-polyurethane\"\u003espray polyurethane and clear spray finishes\u003c\/a\u003e or a hand-rubbed oil from \u003ca href=\"\/collections\/wood-oil-finishes-paste-wax\"\u003ewood finishing oils and paste wax\u003c\/a\u003e.\u003c\/p\u003e\n\u003cp\u003eShop related: \u003ca href=\"\/collections\/minwax-wood-finish-stain\"\u003eevery Minwax Wood Finish stain color\u003c\/a\u003e, \u003ca href=\"\/collections\/minwax-wood-stains-finishes\"\u003eMinwax\u003c\/a\u003e, \u003ca href=\"\/collections\/varathane\"\u003eVarathane\u003c\/a\u003e, \u003ca href=\"\/collections\/general-finishes\"\u003eGeneral Finishes\u003c\/a\u003e, \u003ca href=\"\/collections\/old-masters\"\u003eOld Masters\u003c\/a\u003e, \u003ca href=\"\/collections\/wood-filler-putty\"\u003ewood filler and wood putty\u003c\/a\u003e, and the \u003ca href=\"\/pages\/furniture-refinishing-project-cart\"\u003efurniture refinishing cart\u003c\/a\u003e.\u003c\/p\u003e\n\u003c\/div\u003e\n","products":[{"product_id":"varathane-premium-wood-conditioner-clear-half-pint","title":"Varathane Premium Wood Conditioner, Clear, Half Pint","description":"\u003cp\u003e\u003cstrong\u003eVarathane Premium Wood Conditioner, Clear, Half Pint\u003c\/strong\u003e is intended for interior use. \u003c\/p\u003e\n\u003ch3\u003eFeatures\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHelps even stain color\u003c\/li\u003e\n\u003cli\u003eClear conditioner\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eBest for\u003c\/h3\u003e\u003cp\u003eInterior wood furniture; Cabinets; Doors; Trim; Floors; Paneling\u003c\/p\u003e\u003ch3\u003eSpecs\u003c\/h3\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003eColor or finish\u003c\/th\u003e\n\u003ctd\u003eClear\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSelected size\u003c\/th\u003e\n\u003ctd\u003eHalf Pint\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBase\u003c\/th\u003e\n\u003ctd\u003eoil-based modified alkyd\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eUse\u003c\/th\u003e\n\u003ctd\u003einterior\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoverage\u003c\/th\u003e\n\u003ctd\u003e440-880 sq ft\/gallon\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eTouch dry\u003c\/th\u003e\n\u003ctd\u003e1-2 hours\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRecoat\u003c\/th\u003e\n\u003ctd\u003e30 minutes before stain\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApplication conditions\u003c\/th\u003e\n\u003ctd\u003e55-90°F; relative humidity below 85%\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply with\u003c\/th\u003e\n\u003ctd\u003eBrush; Lint-free cloth\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCleanup\u003c\/th\u003e\n\u003ctd\u003eMineral spirits or paint thinner\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVOC\u003c\/th\u003e\n\u003ctd\u003e\u0026lt;550\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eTopcoat compatibility\u003c\/th\u003e\n\u003ctd\u003eUse before oil-based wood stain; not recommended with water-based stains\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eManufacturer part #\u003c\/th\u003e\n\u003ctd\u003e211776\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch3\u003eHow to apply\u003c\/h3\u003e\u003cp\u003eStart with the manufacturer's preparation steps: Remove prior coating to bare wood; Sand 120, 150, 180, then 220 grit; Remove sanding dust, grease and glue.\u003c\/p\u003e\u003ch3\u003eGood to know\u003c\/h3\u003e\u003cp\u003eUse limits: Water-based stains.\u003c\/p\u003e\u003cp\u003eDanger: Flammable liquid and vapor; causes skin and eye irritation; harmful if inhaled; may cause genetic defects, cancer, reproductive harm, and organ damage with prolonged exposure.\u003c\/p\u003e\u003ch3\u003eQuestions\u003c\/h3\u003e\u003ch4\u003eHow much will I need?\u003c\/h4\u003e\u003cp\u003eUse these manufacturer coverage figures: 440-880 sq ft\/gallon. Match the figure to the container size, and account for the stated number of coats.\u003c\/p\u003e\u003ch4\u003eWhen can I apply another coat?\u003c\/h4\u003e\u003cp\u003eThe listed manufacturer recoat guidance is 30 minutes before stain. Follow the application conditions and instructions for this product.\u003c\/p\u003e\u003cp\u003e\u003ca href=\"https:\/\/www.rustoleum.com\/~\/media\/DigitalEncyclopedia\/Documents\/RustoleumUSA\/TDS\/English\/CBG\/Varathane\/VAR-04_Varathane_Premium_Wood_Conditioner_TDS.ashx\" target=\"_blank\" rel=\"noopener\"\u003eManufacturer directions and product information\u003c\/a\u003e\u003c\/p\u003e","brand":"Varathane","offers":[{"title":"Default Title","offer_id":67673242304822,"sku":"211776","price":11.36,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0931\/9750\/0726\/files\/020066128449.jpg?v=1791581773"},{"product_id":"varathane-premium-wood-conditioner-clear-quart","title":"Varathane Premium Wood Conditioner, Clear, Quart","description":"\u003cp\u003e\u003cstrong\u003eVarathane Premium Wood Conditioner, Clear, Quart\u003c\/strong\u003e is intended for interior use. \u003c\/p\u003e\n\u003ch3\u003eFeatures\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHelps even stain color\u003c\/li\u003e\n\u003cli\u003eClear conditioner\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eBest for\u003c\/h3\u003e\u003cp\u003eInterior wood furniture; Cabinets; Doors; Trim; Floors; Paneling\u003c\/p\u003e\u003ch3\u003eSpecs\u003c\/h3\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003eColor or finish\u003c\/th\u003e\n\u003ctd\u003eClear\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSelected size\u003c\/th\u003e\n\u003ctd\u003eQuart\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBase\u003c\/th\u003e\n\u003ctd\u003eoil-based modified alkyd\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eUse\u003c\/th\u003e\n\u003ctd\u003einterior\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoverage\u003c\/th\u003e\n\u003ctd\u003e440-880 sq ft\/gallon\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eTouch dry\u003c\/th\u003e\n\u003ctd\u003e1-2 hours\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRecoat\u003c\/th\u003e\n\u003ctd\u003e30 minutes before stain\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApplication conditions\u003c\/th\u003e\n\u003ctd\u003e55-90°F; relative humidity below 85%\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply with\u003c\/th\u003e\n\u003ctd\u003eBrush; Lint-free cloth\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCleanup\u003c\/th\u003e\n\u003ctd\u003eMineral spirits or paint thinner\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVOC\u003c\/th\u003e\n\u003ctd\u003e\u0026lt;550\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eTopcoat compatibility\u003c\/th\u003e\n\u003ctd\u003eUse before oil-based wood stain; not recommended with water-based stains\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eManufacturer part #\u003c\/th\u003e\n\u003ctd\u003e211775H\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch3\u003eHow to apply\u003c\/h3\u003e\u003cp\u003eStart with the manufacturer's preparation steps: Remove prior coating to bare wood; Sand 120, 150, 180, then 220 grit; Remove sanding dust, grease and glue.\u003c\/p\u003e\u003ch3\u003eGood to know\u003c\/h3\u003e\u003cp\u003eUse limits: Water-based stains.\u003c\/p\u003e\u003cp\u003eDanger: Flammable liquid and vapor; causes skin and eye irritation; harmful if inhaled; may cause genetic defects, cancer, reproductive harm, and organ damage with prolonged exposure.\u003c\/p\u003e\u003ch3\u003eQuestions\u003c\/h3\u003e\u003ch4\u003eHow much will I need?\u003c\/h4\u003e\u003cp\u003eUse these manufacturer coverage figures: 440-880 sq ft\/gallon. Match the figure to the container size, and account for the stated number of coats.\u003c\/p\u003e\u003ch4\u003eWhen can I apply another coat?\u003c\/h4\u003e\u003cp\u003eThe listed manufacturer recoat guidance is 30 minutes before stain. Follow the application conditions and instructions for this product.\u003c\/p\u003e\u003cp\u003e\u003ca href=\"https:\/\/www.rustoleum.com\/~\/media\/DigitalEncyclopedia\/Documents\/RustoleumUSA\/TDS\/English\/CBG\/Varathane\/VAR-04_Varathane_Premium_Wood_Conditioner_TDS.ashx\" target=\"_blank\" rel=\"noopener\"\u003eManufacturer directions and product information\u003c\/a\u003e\u003c\/p\u003e","brand":"Varathane","offers":[{"title":"Default Title","offer_id":67673242337590,"sku":"211775H","price":17.11,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0931\/9750\/0726\/files\/020066128432.jpg?v=1791581775"},{"product_id":"varathane-premium-wood-conditioner-clear-gallon","title":"Varathane Premium Wood Conditioner, Clear, Gallon","description":"\u003cp\u003e\u003cstrong\u003eVarathane Premium Wood Conditioner, Clear, Gallon\u003c\/strong\u003e is intended for interior use. \u003c\/p\u003e\n\u003ch3\u003eFeatures\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHelps even stain color\u003c\/li\u003e\n\u003cli\u003eClear conditioner\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eBest for\u003c\/h3\u003e\u003cp\u003eInterior wood furniture; Cabinets; Doors; Trim; Floors; Paneling\u003c\/p\u003e\u003ch3\u003eSpecs\u003c\/h3\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003eColor or finish\u003c\/th\u003e\n\u003ctd\u003eClear\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSelected size\u003c\/th\u003e\n\u003ctd\u003eGallon\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBase\u003c\/th\u003e\n\u003ctd\u003eoil-based modified alkyd\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eUse\u003c\/th\u003e\n\u003ctd\u003einterior\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoverage\u003c\/th\u003e\n\u003ctd\u003e440-880 sq ft\/gallon\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eTouch dry\u003c\/th\u003e\n\u003ctd\u003e1-2 hours\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRecoat\u003c\/th\u003e\n\u003ctd\u003e30 minutes before stain\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApplication conditions\u003c\/th\u003e\n\u003ctd\u003e55-90°F; relative humidity below 85%\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply with\u003c\/th\u003e\n\u003ctd\u003eBrush; Lint-free cloth\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCleanup\u003c\/th\u003e\n\u003ctd\u003eMineral spirits or paint thinner\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVOC\u003c\/th\u003e\n\u003ctd\u003e\u0026lt;550\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eTopcoat compatibility\u003c\/th\u003e\n\u003ctd\u003eUse before oil-based wood stain; not recommended with water-based stains\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eManufacturer part #\u003c\/th\u003e\n\u003ctd\u003e211774\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch3\u003eHow to apply\u003c\/h3\u003e\u003cp\u003eStart with the manufacturer's preparation steps: Remove prior coating to bare wood; Sand 120, 150, 180, then 220 grit; Remove sanding dust, grease and glue.\u003c\/p\u003e\u003ch3\u003eGood to know\u003c\/h3\u003e\u003cp\u003eUse limits: Water-based stains.\u003c\/p\u003e\u003cp\u003eDanger: Flammable liquid and vapor; causes skin and eye irritation; harmful if inhaled; may cause genetic defects, cancer, reproductive harm, and organ damage with prolonged exposure.\u003c\/p\u003e\u003ch3\u003eQuestions\u003c\/h3\u003e\u003ch4\u003eHow much will I need?\u003c\/h4\u003e\u003cp\u003eUse these manufacturer coverage figures: 440-880 sq ft\/gallon. Match the figure to the container size, and account for the stated number of coats.\u003c\/p\u003e\u003ch4\u003eWhen can I apply another coat?\u003c\/h4\u003e\u003cp\u003eThe listed manufacturer recoat guidance is 30 minutes before stain. Follow the application conditions and instructions for this product.\u003c\/p\u003e\u003cp\u003e\u003ca href=\"https:\/\/www.rustoleum.com\/~\/media\/DigitalEncyclopedia\/Documents\/RustoleumUSA\/TDS\/English\/CBG\/Varathane\/VAR-04_Varathane_Premium_Wood_Conditioner_TDS.ashx\" target=\"_blank\" rel=\"noopener\"\u003eManufacturer directions and product information\u003c\/a\u003e\u003c\/p\u003e","brand":"Varathane","offers":[{"title":"Default Title","offer_id":67673242370358,"sku":"211774","price":65.02,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0931\/9750\/0726\/files\/020066128425.jpg?v=1791581778"},{"product_id":"general-finishes-pre-stain-conditioner-natural-pint","title":"General Finishes Pre-Stain Conditioner, Natural, Pint","description":"\u003cp\u003eGeneral Finishes Water-Based Pre-Stain Conditioner Natural, Pint, controls stain absorption on raw indoor wood. This pint can covers about 50–75 sq ft, depending on the wood and application. Use it before a separate water-based stain to reduce blotching; test your full finishing process because conditioning can lighten the final color.\u003c\/p\u003e\n\u003ch3\u003eFeatures\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHelps control uneven absorption on hard-to-stain raw wood.\u003c\/li\u003e\n\u003cli\u003eColorless formula prepares the surface for a water-based stain.\u003c\/li\u003e\n\u003cli\u003eUseful on woods such as maple, pine and cherry.\u003c\/li\u003e\n\u003cli\u003eWater-based tools clean up promptly with soap and water.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eBest for\u003c\/h3\u003e\u003cp\u003eRaw indoor wood furniture, cabinets, doors and trim before applying GF water-based stain. Natural is the clear pre-stain formula, not a pigmented Natural Oak color. Test the complete conditioner, stain and topcoat process on your wood.\u003c\/p\u003e\n\u003ch3\u003eSpecs\u003c\/h3\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003eColor \/ size\u003c\/th\u003e\n\u003ctd\u003eNatural \/ Pint\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBase \/ use\u003c\/th\u003e\n\u003ctd\u003eWater-based wood conditioner \/ interior raw wood\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoverage\u003c\/th\u003e\n\u003ctd\u003eAbout 50–75 sq ft per can\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eTouch dry\u003c\/th\u003e\n\u003ctd\u003e10 minutes or longer\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStain interval \/ full cure\u003c\/th\u003e\n\u003ctd\u003eDetailed directions: 20–30 minutes; specification table: 30 minutes or longer \/ no full-cure duration stated\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoats\u003c\/th\u003e\n\u003ctd\u003e1 conditioner coat before water-based stain\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply with\u003c\/th\u003e\n\u003ctd\u003eSynthetic-bristle or foam brush, pad, roller or spray\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThinning\u003c\/th\u003e\n\u003ctd\u003eDistilled water if needed: start at 5%, up to 10% by volume\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCleanup\u003c\/th\u003e\n\u003ctd\u003eSoap and water or GF Brush \u0026amp; Gun Cleaner, immediately\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVOC\u003c\/th\u003e\n\u003ctd\u003eUnder 215 g\/L, Natural\/Pre-Stain Conditioner SDS revised February 2, 2024\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eManufacturer part #\u003c\/th\u003e\n\u003ctd\u003eWNPT\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\u003ch3\u003eHow to apply\u003c\/h3\u003e\u003col\u003e\n\u003cli\u003eSand open-grain wood through 120, 150 and 180 grit; closed-grain wood with 150 then 220 grit. Remove dust. Do not use steel wool with water-based finishes. To reduce grain raise, dampen after sanding, dry fully and lightly sand with a 220–320 foam pad.\u003c\/li\u003e\n\u003cli\u003eVentilate and stir before and throughout use. Test the entire finishing process. Work in manageable sections, applying a liberal coat with a brush, pad or roller.\u003c\/li\u003e\n\u003cli\u003eWipe excess evenly along the grain with absorbent paper or shop towels. Detailed instructions say to let conditioner dry 20 minutes but no more than 30 before GF water-based stain in ideal conditions, about 70°F and 50–70% humidity.\u003c\/li\u003e\n\u003cli\u003eApply your tested stain and follow its own application and topcoat directions. The conditioner specification table separately lists 30 minutes or more before stain. Check the current can instructions; confirm with GF if conditions or directions conflict before starting.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eGood to know\u003c\/h3\u003e\u003cp\u003eConditioning limits color absorption, so your desired depth may require a darker stain. It does not eliminate wood variation. Do not use over an existing finish, outdoors, or with linseed or Danish oils. Use Extender only under the manufacturer’s locally permitted instructions. The exact SDS lists no signal word and identifies the mixture as not classified; the product page includes eye-irritation precautions and a California Proposition 65 cancer\/reproductive-harm warning. Read the can label and \u003ca href=\"https:\/\/generalfinishes.com\/sites\/default\/files\/documents\/files\/2024-02\/SDS-English-Water-Based-Pre-Stain-Wood-Conditioner-NATURAL-Water-Base-General-Finishes-US-HCS-2012-v1-2024-02-02.PDF\"\u003ematching Natural safety sheet\u003c\/a\u003e; follow handling and local disposal rules.\u003c\/p\u003e\n\u003ch3\u003eQuestions\u003c\/h3\u003e\u003cp\u003e\u003cstrong\u003eWill Natural add stain color?\u003c\/strong\u003e No. It is a colorless preparation step before a separate stain.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWill my stain become lighter?\u003c\/strong\u003e Reduced absorption can make the result lighter; test a darker stain if needed.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eCan I use it on a finished cabinet?\u003c\/strong\u003e No. The manufacturer limits this conditioner to raw wood.\u003c\/p\u003e","brand":"General Finishes","offers":[{"title":"Default Title","offer_id":67673251512630,"sku":"WNPT","price":25.16,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0931\/9750\/0726\/files\/606016100002.jpg?v=1791582018"},{"product_id":"general-finishes-pre-stain-conditioner-natural-quart","title":"General Finishes Pre-Stain Conditioner, Natural, Quart","description":"\u003cp\u003eGeneral Finishes Water-Based Pre-Stain Conditioner Natural, Quart, controls stain absorption on raw indoor wood. This quart can covers about 100–150 sq ft, depending on the wood and application. Use it before a separate water-based stain to reduce blotching; test your full finishing process because conditioning can lighten the final color.\u003c\/p\u003e\n\u003ch3\u003eFeatures\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eHelps control uneven absorption on hard-to-stain raw wood.\u003c\/li\u003e\n\u003cli\u003eColorless formula prepares the surface for a water-based stain.\u003c\/li\u003e\n\u003cli\u003eUseful on woods such as maple, pine and cherry.\u003c\/li\u003e\n\u003cli\u003eWater-based tools clean up promptly with soap and water.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eBest for\u003c\/h3\u003e\u003cp\u003eRaw indoor wood furniture, cabinets, doors and trim before applying GF water-based stain. Natural is the clear pre-stain formula, not a pigmented Natural Oak color. Test the complete conditioner, stain and topcoat process on your wood.\u003c\/p\u003e\n\u003ch3\u003eSpecs\u003c\/h3\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003eColor \/ size\u003c\/th\u003e\n\u003ctd\u003eNatural \/ Quart\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBase \/ use\u003c\/th\u003e\n\u003ctd\u003eWater-based wood conditioner \/ interior raw wood\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoverage\u003c\/th\u003e\n\u003ctd\u003eAbout 100–150 sq ft per can\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eTouch dry\u003c\/th\u003e\n\u003ctd\u003e10 minutes or longer\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStain interval \/ full cure\u003c\/th\u003e\n\u003ctd\u003eDetailed directions: 20–30 minutes; specification table: 30 minutes or longer \/ no full-cure duration stated\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoats\u003c\/th\u003e\n\u003ctd\u003e1 conditioner coat before water-based stain\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply with\u003c\/th\u003e\n\u003ctd\u003eSynthetic-bristle or foam brush, pad, roller or spray\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThinning\u003c\/th\u003e\n\u003ctd\u003eDistilled water if needed: start at 5%, up to 10% by volume\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCleanup\u003c\/th\u003e\n\u003ctd\u003eSoap and water or GF Brush \u0026amp; Gun Cleaner, immediately\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVOC\u003c\/th\u003e\n\u003ctd\u003eUnder 215 g\/L, Natural\/Pre-Stain Conditioner SDS revised February 2, 2024\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eManufacturer part #\u003c\/th\u003e\n\u003ctd\u003eWNQT\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\u003ch3\u003eHow to apply\u003c\/h3\u003e\u003col\u003e\n\u003cli\u003eSand open-grain wood through 120, 150 and 180 grit; closed-grain wood with 150 then 220 grit. Remove dust. Do not use steel wool with water-based finishes. To reduce grain raise, dampen after sanding, dry fully and lightly sand with a 220–320 foam pad.\u003c\/li\u003e\n\u003cli\u003eVentilate and stir before and throughout use. Test the entire finishing process. Work in manageable sections, applying a liberal coat with a brush, pad or roller.\u003c\/li\u003e\n\u003cli\u003eWipe excess evenly along the grain with absorbent paper or shop towels. Detailed instructions say to let conditioner dry 20 minutes but no more than 30 before GF water-based stain in ideal conditions, about 70°F and 50–70% humidity.\u003c\/li\u003e\n\u003cli\u003eApply your tested stain and follow its own application and topcoat directions. The conditioner specification table separately lists 30 minutes or more before stain. Check the current can instructions; confirm with GF if conditions or directions conflict before starting.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eGood to know\u003c\/h3\u003e\u003cp\u003eConditioning limits color absorption, so your desired depth may require a darker stain. It does not eliminate wood variation. Do not use over an existing finish, outdoors, or with linseed or Danish oils. Use Extender only under the manufacturer’s locally permitted instructions. The exact SDS lists no signal word and identifies the mixture as not classified; the product page includes eye-irritation precautions and a California Proposition 65 cancer\/reproductive-harm warning. Read the can label and \u003ca href=\"https:\/\/generalfinishes.com\/sites\/default\/files\/documents\/files\/2024-02\/SDS-English-Water-Based-Pre-Stain-Wood-Conditioner-NATURAL-Water-Base-General-Finishes-US-HCS-2012-v1-2024-02-02.PDF\"\u003ematching Natural safety sheet\u003c\/a\u003e; follow handling and local disposal rules.\u003c\/p\u003e\n\u003ch3\u003eQuestions\u003c\/h3\u003e\u003cp\u003e\u003cstrong\u003eWill Natural add stain color?\u003c\/strong\u003e No. It is a colorless preparation step before a separate stain.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWill my stain become lighter?\u003c\/strong\u003e Reduced absorption can make the result lighter; test a darker stain if needed.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eCan I use it on a finished cabinet?\u003c\/strong\u003e No. The manufacturer limits this conditioner to raw wood.\u003c\/p\u003e","brand":"General Finishes","offers":[{"title":"Default Title","offer_id":67673251545398,"sku":"WNQT","price":39.46,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0931\/9750\/0726\/files\/606016100170.jpg?v=1791582020"},{"product_id":"general-finishes-oil-based-pre-stain-wood-conditioner-natural-quart","title":"General Finishes Oil-Based Pre-Stain Wood Conditioner, Natural, Quart","description":"\u003cp\u003e\u003cstrong\u003eGeneral Finishes Oil-Based Pre-Stain Wood Conditioner, Natural, Quart\u003c\/strong\u003e is intended for Interior use. \u003c\/p\u003e\n\u003ch3\u003eFeatures\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eReduces blotching and streaking\u003c\/li\u003e\n\u003cli\u003ePromotes uniform oil-stain absorption\u003c\/li\u003e\n\u003cli\u003eAmber natural appearance\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eBest for\u003c\/h3\u003e\u003cp\u003eNew soft and porous wood; Aspen; Cherry; Birch; Poplar; Pine\u003c\/p\u003e\u003ch3\u003eSpecs\u003c\/h3\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003eColor or finish\u003c\/th\u003e\n\u003ctd\u003eNatural; dries amber\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSelected size\u003c\/th\u003e\n\u003ctd\u003eQuart\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBase\u003c\/th\u003e\n\u003ctd\u003eOil-based wood conditioner\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eUse\u003c\/th\u003e\n\u003ctd\u003eInterior\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoverage\u003c\/th\u003e\n\u003ctd\u003e45-50 sq ft\/half-pint; 180-200 sq ft\/quart\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eTouch dry\u003c\/th\u003e\n\u003ctd\u003e30+ minutes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRecoat\u003c\/th\u003e\n\u003ctd\u003eApply oil-based stain after 30 minutes and no later than 2 hours\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApplication conditions\u003c\/th\u003e\n\u003ctd\u003eIdeal 70°F and 50% humidity\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoats\u003c\/th\u003e\n\u003ctd\u003e1\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply with\u003c\/th\u003e\n\u003ctd\u003eClean cotton rag; Natural bristle or foam brush; Staining pad; Pad applicator\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThinning\u003c\/th\u003e\n\u003ctd\u003eDo not thin\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCleanup\u003c\/th\u003e\n\u003ctd\u003eMineral spirits or waterless hand cleaner\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVOC\u003c\/th\u003e\n\u003ctd\u003e\u0026lt;686.514 g\/L\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eTopcoat compatibility\u003c\/th\u003e\n\u003ctd\u003eUse before oil-based stain; can also dilute GF oil-based stain 5%-15% by volume\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eManufacturer part #\u003c\/th\u003e\n\u003ctd\u003ePSQT\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch3\u003eHow to apply\u003c\/h3\u003e\u003cp\u003eStart with the manufacturer's preparation steps: Sand open-grain wood 120, 150, then 180 grit; Sand closed-grain wood no finer than 180 grit; Remove dust.\u003c\/p\u003e\u003col\u003e\n\u003cli\u003eSand raw wood and remove dust\u003c\/li\u003e\n\u003cli\u003eStir; do not thin\u003c\/li\u003e\n\u003cli\u003eApply one coat and let penetrate at least 10 minutes\u003c\/li\u003e\n\u003cli\u003eWipe excess\u003c\/li\u003e\n\u003cli\u003eApply oil-based stain after 30 minutes and within 2 hours\u003c\/li\u003e\n\u003c\/ol\u003e\u003ch3\u003eGood to know\u003c\/h3\u003e\u003cp\u003eUse limits: Existing sealed finishes; Water-based stain system; Spray application.\u003c\/p\u003e\u003cp\u003eDanger: 2021 SDS: flammable liquid and vapor; aspiration hazard; may cause allergic skin reaction and cancer; causes organ damage from prolonged or repeated exposure; harmful to aquatic life.\u003c\/p\u003e\u003cp\u003e: Product page California Prop 65 warning lists ethylbenzene.\u003c\/p\u003e\u003ch3\u003eQuestions\u003c\/h3\u003e\u003ch4\u003eHow much will I need?\u003c\/h4\u003e\u003cp\u003eUse these manufacturer coverage figures: 45-50 sq ft\/half-pint; 180-200 sq ft\/quart. Match the figure to the container size, and account for the stated number of coats.\u003c\/p\u003e\u003ch4\u003eWhen can I apply another coat?\u003c\/h4\u003e\u003cp\u003eThe listed manufacturer recoat guidance is Apply oil-based stain after 30 minutes and no later than 2 hours. Follow the application conditions and instructions for this product.\u003c\/p\u003e\u003cp\u003e\u003ca href=\"https:\/\/generalfinishes.com\/wood-finishes-retail\/oil-based-wood-stains-sealers\/oil-based-pre-stain-wood-conditioner\" target=\"_blank\" rel=\"noopener\"\u003eManufacturer directions and product information\u003c\/a\u003e\u003c\/p\u003e","brand":"General Finishes","offers":[{"title":"Default Title","offer_id":67673257902390,"sku":"PSQT","price":39.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0931\/9750\/0726\/files\/606016104000.jpg?v=1791582195"},{"product_id":"minwax-pre-stain-wood-conditioner-clear-half-pint","title":"Minwax Pre-Stain Wood Conditioner, Clear, Half Pint","description":"\u003cp\u003e\u003cstrong\u003eMinwax Pre-Stain Wood Conditioner, Clear, Half Pint\u003c\/strong\u003e is the Clear, Half Pint item in this product line. \u003c\/p\u003e\n\u003ch3\u003eFeatures\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ePromotes even oil-based stain absorption\u003c\/li\u003e\n\u003cli\u003eReduces streaking and blotching\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eBest for\u003c\/h3\u003e\u003cp\u003eNew or bare wood before oil-based stain; Pine; Fir; Spruce; Maple; Alder; Aspen\u003c\/p\u003e\u003ch3\u003eSpecs\u003c\/h3\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003eColor or finish\u003c\/th\u003e\n\u003ctd\u003eClear\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSelected size\u003c\/th\u003e\n\u003ctd\u003eHalf Pint\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBase\u003c\/th\u003e\n\u003ctd\u003eoil\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoverage\u003c\/th\u003e\n\u003ctd\u003e500 sq ft\/gallon\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eTouch dry\u003c\/th\u003e\n\u003ctd\u003e15 minutes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoats\u003c\/th\u003e\n\u003ctd\u003e1; additional coats may be used on highly absorbent wood\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply with\u003c\/th\u003e\n\u003ctd\u003eBrush; Cloth\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThinning\u003c\/th\u003e\n\u003ctd\u003eDo not thin\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCleanup\u003c\/th\u003e\n\u003ctd\u003eMineral spirits, paint thinner or turpentine\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVOC\u003c\/th\u003e\n\u003ctd\u003e350\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eTopcoat compatibility\u003c\/th\u003e\n\u003ctd\u003eUse before Minwax Wood Finish, Gel Stain, PolyShades or WoodSheen; stain within 2 hours\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eManufacturer part #\u003c\/th\u003e\n\u003ctd\u003e13407\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch3\u003eHow to apply\u003c\/h3\u003e\u003cp\u003eStart with the manufacturer's preparation steps: Clean, raw, dry wood; Sand with 220 grit and remove dust.\u003c\/p\u003e\u003col\u003e\n\u003cli\u003eApply to clean raw wood with brush or cloth\u003c\/li\u003e\n\u003cli\u003eAllow to penetrate 5-15 minutes\u003c\/li\u003e\n\u003cli\u003eWipe off excess\u003c\/li\u003e\n\u003cli\u003eApply oil-based stain within 2 hours\u003c\/li\u003e\n\u003c\/ol\u003e\u003ch3\u003eGood to know\u003c\/h3\u003e\u003cp\u003eUse limits: Water-based stains.\u003c\/p\u003e\u003cp\u003eDanger: Flammable liquid and vapor; aspiration hazard; may cause drowsiness or dizziness and organ damage from repeated exposure.\u003c\/p\u003e\u003cp\u003e: Soaked rags may spontaneously catch fire; California cancer warning.\u003c\/p\u003e\u003ch3\u003eQuestions\u003c\/h3\u003e\u003ch4\u003eHow much will I need?\u003c\/h4\u003e\u003cp\u003eUse these manufacturer coverage figures: 500 sq ft\/gallon. Match the figure to the container size, and account for the stated number of coats.\u003c\/p\u003e\u003ch4\u003eHow should I clean up?\u003c\/h4\u003e\u003cp\u003eThe manufacturer specifies Mineral spirits, paint thinner or turpentine. Follow the product label for cleanup and disposal.\u003c\/p\u003e\u003cp\u003e\u003ca href=\"https:\/\/www.minwax.com\/en\/products\/preparation\/pre-stain-wood-conditioner\" target=\"_blank\" rel=\"noopener\"\u003eManufacturer directions and product information\u003c\/a\u003e\u003c\/p\u003e","brand":"Minwax","offers":[{"title":"Default Title","offer_id":67673279693110,"sku":"13407","price":7.84,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0931\/9750\/0726\/files\/027426134072_1_0524.jpg?v=1791582555"},{"product_id":"minwax-pre-stain-wood-conditioner-clear-quart","title":"Minwax Pre-Stain Wood Conditioner, Clear, Quart","description":"\u003cp\u003eMinwax Pre-Stain Wood Conditioner, Clear, Quart, is an oil-based conditioner you wipe onto bare wood before an oil-based stain so the color goes on even instead of blotchy. Minwax says it penetrates the grain and evens out how much stain the wood absorbs, which cuts streaking and blotching on soft or porous woods such as pine, fir, alder, aspen, birch and maple. It dries in about 15 minutes, so you can condition and stain in the same session.\u003c\/p\u003e\n\u003ch3\u003eSpecifications (Minwax)\u003c\/h3\u003e\n\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003eSize\u003c\/th\u003e\n\u003ctd\u003e1 quart (UPC 027426615007, Minwax 61500)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBase\u003c\/th\u003e\n\u003ctd\u003eOil based (modified linseed oil and hydrocarbon resin in mineral spirits)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eUse with\u003c\/th\u003e\n\u003ctd\u003eOil-based stains such as Minwax Wood Finish, Gel Stain, PolyShades and WoodSheen\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoverage\u003c\/th\u003e\n\u003ctd\u003eAbout 100 to 125 sq ft per quart\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePenetrate, then wipe\u003c\/th\u003e\n\u003ctd\u003e5 to 15 minutes, then wipe off the excess\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStain window\u003c\/th\u003e\n\u003ctd\u003eStain after about 15 minutes and within 2 hours; on alder, Minwax suggests letting it set 2 hours before staining\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoats\u003c\/th\u003e\n\u003ctd\u003e1; very absorbent wood can take another\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply with\u003c\/th\u003e\n\u003ctd\u003eBrush or cloth; do not thin\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCleanup\u003c\/th\u003e\n\u003ctd\u003eMineral spirits, paint thinner or turpentine\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\u003ch3\u003eHow to use it\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eStart with bare or stripped wood that is clean and dry. Sand with 220 grit in the direction of the grain and remove the dust.\u003c\/li\u003e\n\u003cli\u003eStir well, then brush or wipe the conditioner on with the grain.\u003c\/li\u003e\n\u003cli\u003eLet it penetrate 5 to 15 minutes, then wipe off the excess with a clean, dry cloth.\u003c\/li\u003e\n\u003cli\u003eApply your oil-based stain within 2 hours, then finish with a clear protective coat such as \u003ca href=\"\/collections\/polyurethane\"\u003epolyurethane\u003c\/a\u003e.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eQuestions\u003c\/h3\u003e\n\u003ch4\u003eDo I need wood conditioner on pine or plywood?\u003c\/h4\u003e\n\u003cp\u003eOn soft or porous wood, yes. Minwax says it is especially needed on pine, fir, alder, aspen, birch and maple, and suggests a fingernail test: if your nail dents a hidden spot, condition before staining. Plywood faced with pine, fir or birch falls in that group, so test the stain on a scrap or the back side first.\u003c\/p\u003e\n\u003ch4\u003eShould I use it on oak?\u003c\/h4\u003e\n\u003cp\u003eYou can, but you may not need it. Minwax says the conditioner works on all wood types but can limit or lighten the stain color on hardwoods and less porous woods. Try it on a scrap of the same oak if you want a deep color.\u003c\/p\u003e\n\u003ch4\u003eCan I use it with water-based stain?\u003c\/h4\u003e\n\u003cp\u003eNo. Minwax does not recommend this oil-based conditioner under water-based stains; it makes a separate water-based pre-stain conditioner for those.\u003c\/p\u003e\n\u003ch4\u003eHow long do I wait before staining?\u003c\/h4\u003e\n\u003cp\u003eMinwax lists a 15 minute dry time and says to stain within 2 hours. For alder, it suggests waiting the full 2 hours.\u003c\/p\u003e\n\u003ch4\u003eHow much do I need?\u003c\/h4\u003e\n\u003cp\u003eMinwax lists about 100 to 125 sq ft per quart for one coat. Measure the surfaces you will stain and add a little for end grain and very absorbent wood.\u003c\/p\u003e\n\u003ch3\u003eSafety\u003c\/h3\u003e\n\u003cp\u003eCombustible. Rags, steel wool and sanding dust soaked with this product can catch fire on their own; put them in a sealed, water-filled metal container. Use with fresh air, and read the full label before use.\u003c\/p\u003e\n\u003ch3\u003eShop related\u003c\/h3\u003e\n\u003cp\u003eNext steps: \u003ca href=\"\/collections\/minwax-wood-finish-stain\"\u003eMinwax Wood Finish stain colors\u003c\/a\u003e, \u003ca href=\"\/collections\/curated-wood-stains-gel-stains\"\u003ewood stains and gel stains\u003c\/a\u003e, \u003ca href=\"\/collections\/polyurethane\"\u003epolyurethane for wood\u003c\/a\u003e and the \u003ca href=\"\/collections\/minwax-wood-stains-finishes\"\u003eMinwax\u003c\/a\u003e collection. Also compare \u003ca href=\"\/products\/old-masters-low-voc-wood-conditioner-quart\"\u003eOld Masters Low VOC Wood Conditioner\u003c\/a\u003e.\u003c\/p\u003e\n","brand":"Minwax","offers":[{"title":"Default Title","offer_id":67673279725878,"sku":"61500","price":15.13,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0931\/9750\/0726\/files\/027426615007_1_0524.jpg?v=1791582556"},{"product_id":"minwax-pre-stain-wood-conditioner-clear-gallon","title":"Minwax Pre-Stain Wood Conditioner, Clear, Gallon","description":"\u003cp\u003e\u003cstrong\u003eMinwax Pre-Stain Wood Conditioner, Clear, Gallon\u003c\/strong\u003e is the Clear, Gallon item in this product line. \u003c\/p\u003e\n\u003ch3\u003eFeatures\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ePromotes even oil-based stain absorption\u003c\/li\u003e\n\u003cli\u003eReduces streaking and blotching\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eBest for\u003c\/h3\u003e\u003cp\u003eNew or bare wood before oil-based stain; Pine; Fir; Spruce; Maple; Alder; Aspen\u003c\/p\u003e\u003ch3\u003eSpecs\u003c\/h3\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003eColor or finish\u003c\/th\u003e\n\u003ctd\u003eClear\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSelected size\u003c\/th\u003e\n\u003ctd\u003eGallon\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBase\u003c\/th\u003e\n\u003ctd\u003eoil\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoverage\u003c\/th\u003e\n\u003ctd\u003e500 sq ft\/gallon\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eTouch dry\u003c\/th\u003e\n\u003ctd\u003e15 minutes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoats\u003c\/th\u003e\n\u003ctd\u003e1; additional coats may be used on highly absorbent wood\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply with\u003c\/th\u003e\n\u003ctd\u003eBrush; Cloth\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThinning\u003c\/th\u003e\n\u003ctd\u003eDo not thin\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCleanup\u003c\/th\u003e\n\u003ctd\u003eMineral spirits, paint thinner or turpentine\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVOC\u003c\/th\u003e\n\u003ctd\u003e350\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eTopcoat compatibility\u003c\/th\u003e\n\u003ctd\u003eUse before Minwax Wood Finish, Gel Stain, PolyShades or WoodSheen; stain within 2 hours\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eManufacturer part #\u003c\/th\u003e\n\u003ctd\u003e11500\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch3\u003eHow to apply\u003c\/h3\u003e\u003cp\u003eStart with the manufacturer's preparation steps: Clean, raw, dry wood; Sand with 220 grit and remove dust.\u003c\/p\u003e\u003col\u003e\n\u003cli\u003eApply to clean raw wood with brush or cloth\u003c\/li\u003e\n\u003cli\u003eAllow to penetrate 5-15 minutes\u003c\/li\u003e\n\u003cli\u003eWipe off excess\u003c\/li\u003e\n\u003cli\u003eApply oil-based stain within 2 hours\u003c\/li\u003e\n\u003c\/ol\u003e\u003ch3\u003eGood to know\u003c\/h3\u003e\u003cp\u003eUse limits: Water-based stains.\u003c\/p\u003e\u003cp\u003eDanger: Flammable liquid and vapor; aspiration hazard; may cause drowsiness or dizziness and organ damage from repeated exposure.\u003c\/p\u003e\u003cp\u003e: Soaked rags may spontaneously catch fire; California cancer warning.\u003c\/p\u003e\u003ch3\u003eQuestions\u003c\/h3\u003e\u003ch4\u003eHow much will I need?\u003c\/h4\u003e\u003cp\u003eUse these manufacturer coverage figures: 500 sq ft\/gallon. Match the figure to the container size, and account for the stated number of coats.\u003c\/p\u003e\u003ch4\u003eHow should I clean up?\u003c\/h4\u003e\u003cp\u003eThe manufacturer specifies Mineral spirits, paint thinner or turpentine. Follow the product label for cleanup and disposal.\u003c\/p\u003e\u003cp\u003e\u003ca href=\"https:\/\/www.minwax.com\/en\/products\/preparation\/pre-stain-wood-conditioner\" target=\"_blank\" rel=\"noopener\"\u003eManufacturer directions and product information\u003c\/a\u003e\u003c\/p\u003e","brand":"Minwax","offers":[{"title":"Default Title","offer_id":67673279856950,"sku":"11500","price":41.87,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0931\/9750\/0726\/files\/027426115002_1_0524.jpg?v=1792076220"},{"product_id":"old-masters-low-voc-wood-conditioner-quart","title":"Old Masters Low VOC Wood Conditioner, Quart","description":"\u003cp\u003e\u003cstrong\u003eOld Masters Low VOC Wood Conditioner, Quart\u003c\/strong\u003e is the Clear, Quart item in this product line. \u003c\/p\u003e\n\u003ch3\u003eFeatures\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eClear pre-stain sealer\u003c\/li\u003e\n\u003cli\u003eHelps even stain absorption\u003c\/li\u003e\n\u003cli\u003eLow VOC formula for specified regions\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eBest for\u003c\/h3\u003e\u003cp\u003eSoft woods including pine, fir, maple, poplar, hemlock\u003c\/p\u003e\u003ch3\u003eSpecs\u003c\/h3\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003eColor or finish\u003c\/th\u003e\n\u003ctd\u003eClear\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSelected size\u003c\/th\u003e\n\u003ctd\u003eQuart\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBase\u003c\/th\u003e\n\u003ctd\u003eoil\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoverage\u003c\/th\u003e\n\u003ctd\u003eApproximately 400 to 500 sq ft\/gal\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eTouch dry\u003c\/th\u003e\n\u003ctd\u003eApproximately 8 hours\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRecoat\u003c\/th\u003e\n\u003ctd\u003eApply oil-based stain after 8 hours; water-based stain after at least 24 hours\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoats\u003c\/th\u003e\n\u003ctd\u003eOne application\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply with\u003c\/th\u003e\n\u003ctd\u003ePolyester brush; Nylon brush\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThinning\u003c\/th\u003e\n\u003ctd\u003eDo not thin\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCleanup\u003c\/th\u003e\n\u003ctd\u003ePaint thinner or mineral spirits\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVOC\u003c\/th\u003e\n\u003ctd\u003eMaximum 100\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eTopcoat compatibility\u003c\/th\u003e\n\u003ctd\u003eUnder oil-based stain after 8 hours or water-based stain after minimum 24 hours\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eManufacturer part #\u003c\/th\u003e\n\u003ctd\u003e51104\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch3\u003eHow to apply\u003c\/h3\u003e\u003cp\u003eStart with the manufacturer's preparation steps: Clean and dry; remove dirt, wax, and grease; Sand bare wood medium to fine with grain; remove dust without tack rag; Strip previously finished surfaces to bare wood.\u003c\/p\u003e\u003col\u003e\n\u003cli\u003ePrepare bare wood and remove dust\u003c\/li\u003e\n\u003cli\u003eStir thoroughly\u003c\/li\u003e\n\u003cli\u003eBrush over entire surface\u003c\/li\u003e\n\u003cli\u003eAllow 5 to 15 minutes penetration, wipe excess without leaving surface film\u003c\/li\u003e\n\u003cli\u003eWait 8 hours for oil stain or 24 hours for water stain\u003c\/li\u003e\n\u003c\/ol\u003e\u003ch3\u003eGood to know\u003c\/h3\u003e\u003cp\u003eUse limits: As a sanding sealer.\u003c\/p\u003e\u003cp\u003eDanger: Flammable liquid and vapor; may cause allergic skin reaction, genetic defects, cancer, and suspected reproductive harm.\u003c\/p\u003e\u003cp\u003eDanger: Oil-soaked rags and sanding waste may ignite spontaneously; place in sealed water-filled metal container.\u003c\/p\u003e\u003ch3\u003eQuestions\u003c\/h3\u003e\u003ch4\u003eHow much will I need?\u003c\/h4\u003e\u003cp\u003eUse these manufacturer coverage figures: Approximately 400 to 500 sq ft\/gal. Match the figure to the container size, and account for the stated number of coats.\u003c\/p\u003e\u003ch4\u003eWhen can I apply another coat?\u003c\/h4\u003e\u003cp\u003eThe listed manufacturer recoat guidance is Apply oil-based stain after 8 hours; water-based stain after at least 24 hours. Follow the application conditions and instructions for this product.\u003c\/p\u003e\u003cp\u003e\u003ca href=\"https:\/\/myoldmasters.com\/product\/wood-conditioner\" target=\"_blank\" rel=\"noopener\"\u003eManufacturer directions and product information\u003c\/a\u003e\u003c\/p\u003e","brand":"Old Masters","offers":[{"title":"Default Title","offer_id":67673296863542,"sku":"51104","price":31.8,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0931\/9750\/0726\/files\/086348511040_1_0924.jpg?v=1792089553"},{"product_id":"old-masters-low-voc-wood-conditioner-gallon","title":"Old Masters Low VOC Wood Conditioner, Gallon","description":"\u003cp\u003e\u003cstrong\u003eOld Masters Low VOC Wood Conditioner, Gallon\u003c\/strong\u003e is the Clear, Gallon item in this product line. \u003c\/p\u003e\n\u003ch3\u003eFeatures\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eClear pre-stain sealer\u003c\/li\u003e\n\u003cli\u003eHelps even stain absorption\u003c\/li\u003e\n\u003cli\u003eLow VOC formula for specified regions\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eBest for\u003c\/h3\u003e\u003cp\u003eSoft woods including pine, fir, maple, poplar, hemlock\u003c\/p\u003e\u003ch3\u003eSpecs\u003c\/h3\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003eColor or finish\u003c\/th\u003e\n\u003ctd\u003eClear\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSelected size\u003c\/th\u003e\n\u003ctd\u003eGallon\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBase\u003c\/th\u003e\n\u003ctd\u003eoil\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoverage\u003c\/th\u003e\n\u003ctd\u003eApproximately 400 to 500 sq ft\/gal\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eTouch dry\u003c\/th\u003e\n\u003ctd\u003eApproximately 8 hours\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRecoat\u003c\/th\u003e\n\u003ctd\u003eApply oil-based stain after 8 hours; water-based stain after at least 24 hours\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoats\u003c\/th\u003e\n\u003ctd\u003eOne application\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply with\u003c\/th\u003e\n\u003ctd\u003ePolyester brush; Nylon brush\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThinning\u003c\/th\u003e\n\u003ctd\u003eDo not thin\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCleanup\u003c\/th\u003e\n\u003ctd\u003ePaint thinner or mineral spirits\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVOC\u003c\/th\u003e\n\u003ctd\u003eMaximum 100\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eTopcoat compatibility\u003c\/th\u003e\n\u003ctd\u003eUnder oil-based stain after 8 hours or water-based stain after minimum 24 hours\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eManufacturer part #\u003c\/th\u003e\n\u003ctd\u003e51101\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch3\u003eHow to apply\u003c\/h3\u003e\u003cp\u003eStart with the manufacturer's preparation steps: Clean and dry; remove dirt, wax, and grease; Sand bare wood medium to fine with grain; remove dust without tack rag; Strip previously finished surfaces to bare wood.\u003c\/p\u003e\u003col\u003e\n\u003cli\u003ePrepare bare wood and remove dust\u003c\/li\u003e\n\u003cli\u003eStir thoroughly\u003c\/li\u003e\n\u003cli\u003eBrush over entire surface\u003c\/li\u003e\n\u003cli\u003eAllow 5 to 15 minutes penetration, wipe excess without leaving surface film\u003c\/li\u003e\n\u003cli\u003eWait 8 hours for oil stain or 24 hours for water stain\u003c\/li\u003e\n\u003c\/ol\u003e\u003ch3\u003eGood to know\u003c\/h3\u003e\u003cp\u003eUse limits: As a sanding sealer.\u003c\/p\u003e\u003cp\u003eDanger: Flammable liquid and vapor; may cause allergic skin reaction, genetic defects, cancer, and suspected reproductive harm.\u003c\/p\u003e\u003cp\u003eDanger: Oil-soaked rags and sanding waste may ignite spontaneously; place in sealed water-filled metal container.\u003c\/p\u003e\u003ch3\u003eQuestions\u003c\/h3\u003e\u003ch4\u003eHow much will I need?\u003c\/h4\u003e\u003cp\u003eUse these manufacturer coverage figures: Approximately 400 to 500 sq ft\/gal. Match the figure to the container size, and account for the stated number of coats.\u003c\/p\u003e\u003ch4\u003eWhen can I apply another coat?\u003c\/h4\u003e\u003cp\u003eThe listed manufacturer recoat guidance is Apply oil-based stain after 8 hours; water-based stain after at least 24 hours. Follow the application conditions and instructions for this product.\u003c\/p\u003e\u003cp\u003e\u003ca href=\"https:\/\/myoldmasters.com\/product\/wood-conditioner\" target=\"_blank\" rel=\"noopener\"\u003eManufacturer directions and product information\u003c\/a\u003e\u003c\/p\u003e","brand":"Old Masters","offers":[{"title":"Default Title","offer_id":67673296896310,"sku":"51101","price":106.38,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0931\/9750\/0726\/files\/086348511019_1_0924.jpg?v=1791582874"}],"url":"https:\/\/projectweekenddiy.com\/collections\/pre-stain-wood-conditioner.oembed","provider":"Project Weekend DIY","version":"1.0","type":"link"}