{"title":"General Finishes Water-Based Wood Stain","description":"\u003cp\u003eGeneral Finishes Water-Based Wood Stain is a water-based pigmented stain for interior raw wood such as cabinets, trim, doors and furniture. General Finishes says it gives rich, dark, uniform color on hard-to-stain woods like maple and pine, and it can also go over an existing finish much like a gel stain. It is low odor, cleans up with water and is noncombustible.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eCoverage: up to 600 sq ft per gallon (about 75 sq ft per pint, 150 per quart, calculated).\u003c\/li\u003e\n\u003cli\u003eDry times: touch 30 minutes; second coat or water-based topcoat after 2 hours; 24 hours before an oil-based topcoat (70 F, 50% humidity).\u003c\/li\u003e\n\u003cli\u003eOne coat recommended, two at most. Finish with 3 coats of a GF topcoat such as \u003ca href=\"\/collections\/general-finishes-high-performance\"\u003eHigh Performance Topcoat\u003c\/a\u003e.\u003c\/li\u003e\n\u003cli\u003eBlotchy pine? Start with \u003ca href=\"\/products\/general-finishes-pre-stain-conditioner-natural-quart\"\u003eGF Water-Based Pre-Stain Conditioner Natural\u003c\/a\u003e.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eSource: \u003ca href=\"https:\/\/generalfinishes.com\/sites\/default\/files\/documents\/files\/2020-04\/TDS-2020-03-Water-Based-Wood-Stain-General-Finishes.pdf\" target=\"_blank\" rel=\"noopener\"\u003eGF Water-Based Wood Stain TDS (March 2020)\u003c\/a\u003e. Oil-based option: \u003ca href=\"\/collections\/general-finishes-gel-stain\"\u003eGeneral Finishes Gel Stain\u003c\/a\u003e.\u003c\/p\u003e\n","products":[{"product_id":"general-finishes-water-based-stain-antique-brown-pint","title":"General Finishes Water-Based Stain, Antique Brown, Pint","description":"\u003cp\u003eGeneral Finishes Water-Based Wood Stain in Antique Brown is a water-based pigmented stain for interior raw wood such as cabinets, trim, doors and furniture. General Finishes says its pigments give rich, dark, uniform color on hard-to-stain woods like maple and pine, and that it can also go over an existing finish, much like an oil-based gel stain. It is low odor, cleans up with water and is noncombustible. This is the pint (16 fl oz) can, GF item WAPT.\u003c\/p\u003e\n\u003ch3\u003eHighlights\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eOne coat is recommended; a second coat after the first is fully dry makes the color darker. GF says not to go past two coats.\u003c\/li\u003e\n\u003cli\u003eDry to the touch in 30 minutes; ready for a second coat or a water-based topcoat in 2 hours (70 F, 50% humidity). Wait 24 hours before an oil-based topcoat.\u003c\/li\u003e\n\u003cli\u003eBrush, foam brush, pad, microfiber roller or spray (HVLP 1.1-1.3 mm).\u003c\/li\u003e\n\u003cli\u003eStain gives color only; finish with 3 coats of a GF topcoat.\u003c\/li\u003e\n\u003cli\u003eThin with distilled water, starting at 5% and up to 10% by volume.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eBest for\u003c\/h3\u003e\n\u003cp\u003eIndoor cabinets, furniture, trim and doors, on raw wood or on a cleaned and scuff-sanded existing finish after an adhesion test. It is an interior stain; for outdoor wood, GF makes a separate Exterior 450 stain.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003eColor \/ size\u003c\/th\u003e\n\u003ctd\u003eAntique Brown \/ Pint (16 fl oz)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eGF item \/ UPC\u003c\/th\u003e\n\u003ctd\u003eWAPT \/ 606016103126\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eType\u003c\/th\u003e\n\u003ctd\u003eWater-based pigmented stain, interior\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoverage\u003c\/th\u003e\n\u003ctd\u003eUp to 600 sq ft per gallon (TDS), so up to about 75 sq ft for this can (calculated)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDry times\u003c\/th\u003e\n\u003ctd\u003eTouch 30 minutes; recoat 2 hours; 24 hours before an oil-based topcoat (70 F, 50% humidity; cool, humid or thick coats take longer)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoats\u003c\/th\u003e\n\u003ctd\u003e1 recommended, 2 maximum\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply with\u003c\/th\u003e\n\u003ctd\u003eSynthetic-bristle or foam brush, pad applicator, short-nap or foam roller, or spray. HVLP 1.1-1.3 mm; air-assist airless .007 in; airless fine finish .007-.009 in\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply when\u003c\/th\u003e\n\u003ctd\u003eAbout 70 F and 50% humidity, out of direct sun. GF Accelerator helps in cool or humid conditions, GF Extender in warm or dry ones.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThinning\u003c\/th\u003e\n\u003ctd\u003eDistilled water, 5% up to 10% by volume\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eClean up\u003c\/th\u003e\n\u003ctd\u003eSoap and water (hands); GF Brush \u0026amp; Gun Cleaner (equipment)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSolids\u003c\/th\u003e\n\u003ctd\u003e12-22% by volume, 14-20% by weight (varies by color)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVOC\u003c\/th\u003e\n\u003ctd\u003e125 g\/L on the Antique Brown SDS; the TDS says all colors are under 185 g\/L\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAir quality\u003c\/th\u003e\n\u003ctd\u003eSCAQMD, CARB, Canada, OTC Phase I and II compliant (TDS)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStorage\u003c\/th\u003e\n\u003ctd\u003e50-80 F, tightly sealed, out of sun; best used within a year of the date on the can\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSources\u003c\/th\u003e\n\u003ctd\u003e\n\u003ca href=\"https:\/\/generalfinishes.com\/wood-finishes-retail\/water-based-wood-stains-and-dye-stains\/water-based-wood-stain\" target=\"_blank\" rel=\"noopener\"\u003eGeneral Finishes Water-Based Wood Stain page\u003c\/a\u003e; \u003ca href=\"https:\/\/generalfinishes.com\/sites\/default\/files\/documents\/files\/2020-04\/TDS-2020-03-Water-Based-Wood-Stain-General-Finishes.pdf\" target=\"_blank\" rel=\"noopener\"\u003eTechnical data sheet (March 2020)\u003c\/a\u003e; \u003ca href=\"https:\/\/generalfinishes.com\/sites\/default\/files\/documents\/files\/2024-02\/SDS-English-Water-Based-Wood-Stain-ANTIQUE-BROWN-Water-Base-General-Finishes-US-HCS-2012-v1-2024-02-02.PDF\" target=\"_blank\" rel=\"noopener\"\u003eAntique Brown SDS (rev. 02-Feb-2024)\u003c\/a\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\u003ch3\u003eHow much do I need?\u003c\/h3\u003e\n\u003cp\u003eGF rates the stain at up to 600 sq ft per gallon, so this pint covers up to about 75 sq ft (calculated). Porous or softer woods take more. If you plan a second coat, count it as another full pass.\u003c\/p\u003e\n\u003ch3\u003eHow to apply\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eRaw wood: sand with 120 grit, then 150 or 220 grit, and remove the dust. GF says no finer than 220 on closed-grain woods or 180 on open-grain woods. To reduce grain raise, wet the wood with water, let it dry and sand smooth before staining.\u003c\/li\u003e\n\u003cli\u003eExisting finish: scuff-clean with a non-woven pad and a 50:50 mix of denatured alcohol and water, dry 1-2 hours, then sand lightly with a 220-320 grit sponge. Remove dust and test adhesion.\u003c\/li\u003e\n\u003cli\u003eWork in a ventilated area and stir before and during use. On raw wood, apply a liberal amount to one section at a time, then wipe off the excess with the grain using absorbent terry cloth or paper towel. Do not use cotton T-shirts; they push the stain around. Correct lap marks right away by rewetting the whole section and wiping again.\u003c\/li\u003e\n\u003cli\u003eOver an existing finish, use thin coats with a foam brush or staining pad and avoid heavy build.\u003c\/li\u003e\n\u003cli\u003eLet it dry at least 2 hours (24 hours under an oil-based topcoat), then apply 3 coats of a GF topcoat. Take care not to sand through the first topcoat coat.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eGood to know\u003c\/h3\u003e\n\u003cp\u003eStain color changes with wood species, prep, lighting and the topcoat, so test the full stain-and-topcoat process on scrap first. On blotch-prone woods like pine, GF Water-Based Pre-Stain Conditioner Natural evens out color but limits how much stain soaks in, so a darker color may be needed. GF notes that California users who add more than 2% GF Extender make the stain non-compliant under SCAQMD rules. The Antique Brown SDS (rev. 02-Feb-2024) uses the signal word Danger: may cause cancer. Wear the protection it lists, and use the respirator GF specifies when spraying. Store between 50 and 80 F and do not pour leftovers down the drain.\u003c\/p\u003e\n\u003ch3\u003eQuestions\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eCan I use it over a finished cabinet?\u003c\/strong\u003e Yes, after cleaning, scuff-sanding and an adhesion test, using thin coats like a gel stain.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCan I put an oil-based polyurethane over it?\u003c\/strong\u003e Yes. GF says to let the stain dry 24 hours first. Oil-based topcoats can amber, so test the look.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDoes it need a topcoat?\u003c\/strong\u003e Yes. GF says the stain provides color but is not durable on its own; finish with 3 coats of a GF topcoat.\u003c\/p\u003e\n\u003ch3\u003eShop related\u003c\/h3\u003e\n\u003cp\u003eSame color, other size: \u003ca href=\"\/products\/general-finishes-water-based-stain-antique-brown-quart\"\u003eAntique Brown Quart\u003c\/a\u003e. Other colors in this size: \u003ca href=\"\/products\/general-finishes-water-based-stain-black-pint\"\u003eBlack\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-espresso-pint\"\u003eEspresso\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-graystone-pint\"\u003eGraystone\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-walnut-pint\"\u003eWalnut\u003c\/a\u003e. Even out pine with \u003ca href=\"\/products\/general-finishes-pre-stain-conditioner-natural-pint\"\u003eGF Water-Based Pre-Stain Conditioner Natural\u003c\/a\u003e. Topcoat with \u003ca href=\"\/products\/general-finishes-high-performance-water-based-topcoat-clear-satin-quart\"\u003eGF High Performance Topcoat, Satin\u003c\/a\u003e or see all sheens in \u003ca href=\"\/collections\/general-finishes-high-performance\"\u003eHigh Performance Topcoat\u003c\/a\u003e. Prep with a \u003ca href=\"\/products\/3m-softback-contour-sanding-sponge-fine-4-1-2-inch\"\u003e3M Softback sanding sponge\u003c\/a\u003e. Browse every color in \u003ca href=\"\/collections\/general-finishes-water-based-wood-stain\"\u003eGF Water-Based Wood Stain\u003c\/a\u003e, compare \u003ca href=\"\/collections\/curated-wood-stains-gel-stains\"\u003ewood stains and gel stains\u003c\/a\u003e, or plan the job with the \u003ca href=\"\/pages\/furniture-refinishing-project-cart\"\u003efurniture refinishing project cart\u003c\/a\u003e or \u003ca href=\"\/pages\/paint-cabinets-project-cart\"\u003ecabinet project cart\u003c\/a\u003e.\u003c\/p\u003e","brand":"General Finishes","offers":[{"title":"Default Title","offer_id":67673250103606,"sku":"WAPT","price":25.16,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0931\/9750\/0726\/files\/606016103126.jpg?v=1791581973"},{"product_id":"general-finishes-water-based-stain-antique-brown-quart","title":"General Finishes Water-Based Stain, Antique Brown, Quart","description":"\u003cp\u003eGeneral Finishes Water-Based Wood Stain in Antique Brown is a water-based pigmented stain for interior raw wood such as cabinets, trim, doors and furniture. General Finishes says its pigments give rich, dark, uniform color on hard-to-stain woods like maple and pine, and that it can also go over an existing finish, much like an oil-based gel stain. It is low odor, cleans up with water and is noncombustible. This is the quart (32 fl oz) can, GF item WAQT.\u003c\/p\u003e\n\u003ch3\u003eHighlights\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eOne coat is recommended; a second coat after the first is fully dry makes the color darker. GF says not to go past two coats.\u003c\/li\u003e\n\u003cli\u003eDry to the touch in 30 minutes; ready for a second coat or a water-based topcoat in 2 hours (70 F, 50% humidity). Wait 24 hours before an oil-based topcoat.\u003c\/li\u003e\n\u003cli\u003eBrush, foam brush, pad, microfiber roller or spray (HVLP 1.1-1.3 mm).\u003c\/li\u003e\n\u003cli\u003eStain gives color only; finish with 3 coats of a GF topcoat.\u003c\/li\u003e\n\u003cli\u003eThin with distilled water, starting at 5% and up to 10% by volume.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eBest for\u003c\/h3\u003e\n\u003cp\u003eIndoor cabinets, furniture, trim and doors, on raw wood or on a cleaned and scuff-sanded existing finish after an adhesion test. It is an interior stain; for outdoor wood, GF makes a separate Exterior 450 stain.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003eColor \/ size\u003c\/th\u003e\n\u003ctd\u003eAntique Brown \/ Quart (32 fl oz)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eGF item \/ UPC\u003c\/th\u003e\n\u003ctd\u003eWAQT \/ 606016103300\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eType\u003c\/th\u003e\n\u003ctd\u003eWater-based pigmented stain, interior\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoverage\u003c\/th\u003e\n\u003ctd\u003eUp to 600 sq ft per gallon (TDS), so up to about 150 sq ft for this can (calculated)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDry times\u003c\/th\u003e\n\u003ctd\u003eTouch 30 minutes; recoat 2 hours; 24 hours before an oil-based topcoat (70 F, 50% humidity; cool, humid or thick coats take longer)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoats\u003c\/th\u003e\n\u003ctd\u003e1 recommended, 2 maximum\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply with\u003c\/th\u003e\n\u003ctd\u003eSynthetic-bristle or foam brush, pad applicator, short-nap or foam roller, or spray. HVLP 1.1-1.3 mm; air-assist airless .007 in; airless fine finish .007-.009 in\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply when\u003c\/th\u003e\n\u003ctd\u003eAbout 70 F and 50% humidity, out of direct sun. GF Accelerator helps in cool or humid conditions, GF Extender in warm or dry ones.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThinning\u003c\/th\u003e\n\u003ctd\u003eDistilled water, 5% up to 10% by volume\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eClean up\u003c\/th\u003e\n\u003ctd\u003eSoap and water (hands); GF Brush \u0026amp; Gun Cleaner (equipment)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSolids\u003c\/th\u003e\n\u003ctd\u003e12-22% by volume, 14-20% by weight (varies by color)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVOC\u003c\/th\u003e\n\u003ctd\u003e125 g\/L on the Antique Brown SDS; the TDS says all colors are under 185 g\/L\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAir quality\u003c\/th\u003e\n\u003ctd\u003eSCAQMD, CARB, Canada, OTC Phase I and II compliant (TDS)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStorage\u003c\/th\u003e\n\u003ctd\u003e50-80 F, tightly sealed, out of sun; best used within a year of the date on the can\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSources\u003c\/th\u003e\n\u003ctd\u003e\n\u003ca href=\"https:\/\/generalfinishes.com\/wood-finishes-retail\/water-based-wood-stains-and-dye-stains\/water-based-wood-stain\" target=\"_blank\" rel=\"noopener\"\u003eGeneral Finishes Water-Based Wood Stain page\u003c\/a\u003e; \u003ca href=\"https:\/\/generalfinishes.com\/sites\/default\/files\/documents\/files\/2020-04\/TDS-2020-03-Water-Based-Wood-Stain-General-Finishes.pdf\" target=\"_blank\" rel=\"noopener\"\u003eTechnical data sheet (March 2020)\u003c\/a\u003e; \u003ca href=\"https:\/\/generalfinishes.com\/sites\/default\/files\/documents\/files\/2024-02\/SDS-English-Water-Based-Wood-Stain-ANTIQUE-BROWN-Water-Base-General-Finishes-US-HCS-2012-v1-2024-02-02.PDF\" target=\"_blank\" rel=\"noopener\"\u003eAntique Brown SDS (rev. 02-Feb-2024)\u003c\/a\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\u003ch3\u003eHow much do I need?\u003c\/h3\u003e\n\u003cp\u003eGF rates the stain at up to 600 sq ft per gallon, so this quart covers up to about 150 sq ft (calculated). Porous or softer woods take more. If you plan a second coat, count it as another full pass.\u003c\/p\u003e\n\u003ch3\u003eHow to apply\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eRaw wood: sand with 120 grit, then 150 or 220 grit, and remove the dust. GF says no finer than 220 on closed-grain woods or 180 on open-grain woods. To reduce grain raise, wet the wood with water, let it dry and sand smooth before staining.\u003c\/li\u003e\n\u003cli\u003eExisting finish: scuff-clean with a non-woven pad and a 50:50 mix of denatured alcohol and water, dry 1-2 hours, then sand lightly with a 220-320 grit sponge. Remove dust and test adhesion.\u003c\/li\u003e\n\u003cli\u003eWork in a ventilated area and stir before and during use. On raw wood, apply a liberal amount to one section at a time, then wipe off the excess with the grain using absorbent terry cloth or paper towel. Do not use cotton T-shirts; they push the stain around. Correct lap marks right away by rewetting the whole section and wiping again.\u003c\/li\u003e\n\u003cli\u003eOver an existing finish, use thin coats with a foam brush or staining pad and avoid heavy build.\u003c\/li\u003e\n\u003cli\u003eLet it dry at least 2 hours (24 hours under an oil-based topcoat), then apply 3 coats of a GF topcoat. Take care not to sand through the first topcoat coat.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eGood to know\u003c\/h3\u003e\n\u003cp\u003eStain color changes with wood species, prep, lighting and the topcoat, so test the full stain-and-topcoat process on scrap first. On blotch-prone woods like pine, GF Water-Based Pre-Stain Conditioner Natural evens out color but limits how much stain soaks in, so a darker color may be needed. GF notes that California users who add more than 2% GF Extender make the stain non-compliant under SCAQMD rules. The Antique Brown SDS (rev. 02-Feb-2024) uses the signal word Danger: may cause cancer. Wear the protection it lists, and use the respirator GF specifies when spraying. Store between 50 and 80 F and do not pour leftovers down the drain.\u003c\/p\u003e\n\u003ch3\u003eQuestions\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eCan I use it over a finished cabinet?\u003c\/strong\u003e Yes, after cleaning, scuff-sanding and an adhesion test, using thin coats like a gel stain.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCan I put an oil-based polyurethane over it?\u003c\/strong\u003e Yes. GF says to let the stain dry 24 hours first. Oil-based topcoats can amber, so test the look.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDoes it need a topcoat?\u003c\/strong\u003e Yes. GF says the stain provides color but is not durable on its own; finish with 3 coats of a GF topcoat.\u003c\/p\u003e\n\u003ch3\u003eShop related\u003c\/h3\u003e\n\u003cp\u003eSame color, other size: \u003ca href=\"\/products\/general-finishes-water-based-stain-antique-brown-pint\"\u003eAntique Brown Pint\u003c\/a\u003e. Other colors in this size: \u003ca href=\"\/products\/general-finishes-water-based-stain-black-quart\"\u003eBlack\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-espresso-quart\"\u003eEspresso\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-graystone-quart\"\u003eGraystone\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-walnut-quart\"\u003eWalnut\u003c\/a\u003e. Even out pine with \u003ca href=\"\/products\/general-finishes-pre-stain-conditioner-natural-quart\"\u003eGF Water-Based Pre-Stain Conditioner Natural\u003c\/a\u003e. Topcoat with \u003ca href=\"\/products\/general-finishes-high-performance-water-based-topcoat-clear-satin-quart\"\u003eGF High Performance Topcoat, Satin\u003c\/a\u003e or see all sheens in \u003ca href=\"\/collections\/general-finishes-high-performance\"\u003eHigh Performance Topcoat\u003c\/a\u003e. Prep with a \u003ca href=\"\/products\/3m-softback-contour-sanding-sponge-fine-4-1-2-inch\"\u003e3M Softback sanding sponge\u003c\/a\u003e. Browse every color in \u003ca href=\"\/collections\/general-finishes-water-based-wood-stain\"\u003eGF Water-Based Wood Stain\u003c\/a\u003e, compare \u003ca href=\"\/collections\/curated-wood-stains-gel-stains\"\u003ewood stains and gel stains\u003c\/a\u003e, or plan the job with the \u003ca href=\"\/pages\/furniture-refinishing-project-cart\"\u003efurniture refinishing project cart\u003c\/a\u003e or \u003ca href=\"\/pages\/paint-cabinets-project-cart\"\u003ecabinet project cart\u003c\/a\u003e.\u003c\/p\u003e","brand":"General Finishes","offers":[{"title":"Default Title","offer_id":67673250136374,"sku":"WAQT","price":39.46,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0931\/9750\/0726\/files\/606016103300.jpg?v=1791581975"},{"product_id":"general-finishes-water-based-stain-cabernet-pint","title":"General Finishes Water-Based Stain, Cabernet, Pint","description":"\u003cp\u003eGeneral Finishes Water-Based Wood Stain in Cabernet is a water-based pigmented stain for interior raw wood such as cabinets, trim, doors and furniture. General Finishes says its pigments give rich, dark, uniform color on hard-to-stain woods like maple and pine, and that it can also go over an existing finish, much like an oil-based gel stain. It is low odor, cleans up with water and is noncombustible. This is the pint (16 fl oz) can, GF item WZPT.\u003c\/p\u003e\n\u003ch3\u003eHighlights\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eOne coat is recommended; a second coat after the first is fully dry makes the color darker. GF says not to go past two coats.\u003c\/li\u003e\n\u003cli\u003eDry to the touch in 30 minutes; ready for a second coat or a water-based topcoat in 2 hours (70 F, 50% humidity). Wait 24 hours before an oil-based topcoat.\u003c\/li\u003e\n\u003cli\u003eBrush, foam brush, pad, microfiber roller or spray (HVLP 1.1-1.3 mm).\u003c\/li\u003e\n\u003cli\u003eStain gives color only; finish with 3 coats of a GF topcoat.\u003c\/li\u003e\n\u003cli\u003eThin with distilled water, starting at 5% and up to 10% by volume.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eBest for\u003c\/h3\u003e\n\u003cp\u003eIndoor cabinets, furniture, trim and doors, on raw wood or on a cleaned and scuff-sanded existing finish after an adhesion test. It is an interior stain; for outdoor wood, GF makes a separate Exterior 450 stain.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003eColor \/ size\u003c\/th\u003e\n\u003ctd\u003eCabernet \/ Pint (16 fl oz)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eGF item \/ UPC\u003c\/th\u003e\n\u003ctd\u003eWZPT \/ 606016103102\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eType\u003c\/th\u003e\n\u003ctd\u003eWater-based pigmented stain, interior\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoverage\u003c\/th\u003e\n\u003ctd\u003eUp to 600 sq ft per gallon (TDS), so up to about 75 sq ft for this can (calculated)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDry times\u003c\/th\u003e\n\u003ctd\u003eTouch 30 minutes; recoat 2 hours; 24 hours before an oil-based topcoat (70 F, 50% humidity; cool, humid or thick coats take longer)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoats\u003c\/th\u003e\n\u003ctd\u003e1 recommended, 2 maximum\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply with\u003c\/th\u003e\n\u003ctd\u003eSynthetic-bristle or foam brush, pad applicator, short-nap or foam roller, or spray. HVLP 1.1-1.3 mm; air-assist airless .007 in; airless fine finish .007-.009 in\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply when\u003c\/th\u003e\n\u003ctd\u003eAbout 70 F and 50% humidity, out of direct sun. GF Accelerator helps in cool or humid conditions, GF Extender in warm or dry ones.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThinning\u003c\/th\u003e\n\u003ctd\u003eDistilled water, 5% up to 10% by volume\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eClean up\u003c\/th\u003e\n\u003ctd\u003eSoap and water (hands); GF Brush \u0026amp; Gun Cleaner (equipment)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSolids\u003c\/th\u003e\n\u003ctd\u003e12-22% by volume, 14-20% by weight (varies by color)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVOC\u003c\/th\u003e\n\u003ctd\u003eUnder 145 g\/L on the Cabernet SDS (rev. 02-Feb-2024); the TDS says all colors are under 185 g\/L\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAir quality\u003c\/th\u003e\n\u003ctd\u003eSCAQMD, CARB, Canada, OTC Phase I and II compliant (TDS)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStorage\u003c\/th\u003e\n\u003ctd\u003e50-80 F, tightly sealed, out of sun; best used within a year of the date on the can\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSources\u003c\/th\u003e\n\u003ctd\u003e\n\u003ca href=\"https:\/\/generalfinishes.com\/wood-finishes-retail\/water-based-wood-stains-and-dye-stains\/water-based-wood-stain\" target=\"_blank\" rel=\"noopener\"\u003eGeneral Finishes Water-Based Wood Stain page\u003c\/a\u003e; \u003ca href=\"https:\/\/generalfinishes.com\/sites\/default\/files\/documents\/files\/2020-04\/TDS-2020-03-Water-Based-Wood-Stain-General-Finishes.pdf\" target=\"_blank\" rel=\"noopener\"\u003eTechnical data sheet (March 2020)\u003c\/a\u003e; \u003ca href=\"https:\/\/generalfinishes.com\/sites\/default\/files\/documents\/files\/2024-02\/SDS-English-Water-Based-Wood-Stain-CABERNET-Water-Base-General-Finishes-US-HCS-2012-v1-2024-02-02.PDF\" target=\"_blank\" rel=\"noopener\"\u003eCabernet SDS (rev. 02-Feb-2024)\u003c\/a\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\u003ch3\u003eHow much do I need?\u003c\/h3\u003e\n\u003cp\u003eGF rates the stain at up to 600 sq ft per gallon, so this pint covers up to about 75 sq ft (calculated). Porous or softer woods take more. If you plan a second coat, count it as another full pass.\u003c\/p\u003e\n\u003ch3\u003eHow to apply\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eRaw wood: sand with 120 grit, then 150 or 220 grit, and remove the dust. GF says no finer than 220 on closed-grain woods or 180 on open-grain woods. To reduce grain raise, wet the wood with water, let it dry and sand smooth before staining.\u003c\/li\u003e\n\u003cli\u003eExisting finish: scuff-clean with a non-woven pad and a 50:50 mix of denatured alcohol and water, dry 1-2 hours, then sand lightly with a 220-320 grit sponge. Remove dust and test adhesion.\u003c\/li\u003e\n\u003cli\u003eWork in a ventilated area and stir before and during use. On raw wood, apply a liberal amount to one section at a time, then wipe off the excess with the grain using absorbent terry cloth or paper towel. Do not use cotton T-shirts; they push the stain around. Correct lap marks right away by rewetting the whole section and wiping again.\u003c\/li\u003e\n\u003cli\u003eOver an existing finish, use thin coats with a foam brush or staining pad and avoid heavy build.\u003c\/li\u003e\n\u003cli\u003eLet it dry at least 2 hours (24 hours under an oil-based topcoat), then apply 3 coats of a GF topcoat. Take care not to sand through the first topcoat coat.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eGood to know\u003c\/h3\u003e\n\u003cp\u003eStain color changes with wood species, prep, lighting and the topcoat, so test the full stain-and-topcoat process on scrap first. On blotch-prone woods like pine, GF Water-Based Pre-Stain Conditioner Natural evens out color but limits how much stain soaks in, so a darker color may be needed. GF notes that California users who add more than 2% GF Extender make the stain non-compliant under SCAQMD rules. The Cabernet SDS (rev. 02-Feb-2024) lists the mixture as not classified, with no signal word. Use the respirator GF specifies when spraying. Store between 50 and 80 F and do not pour leftovers down the drain.\u003c\/p\u003e\n\u003ch3\u003eQuestions\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eCan I use it over a finished cabinet?\u003c\/strong\u003e Yes, after cleaning, scuff-sanding and an adhesion test, using thin coats like a gel stain.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCan I put an oil-based polyurethane over it?\u003c\/strong\u003e Yes. GF says to let the stain dry 24 hours first. Oil-based topcoats can amber, so test the look.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDoes it need a topcoat?\u003c\/strong\u003e Yes. GF says the stain provides color but is not durable on its own; finish with 3 coats of a GF topcoat.\u003c\/p\u003e\n\u003ch3\u003eShop related\u003c\/h3\u003e\n\u003cp\u003eSame color, other size: \u003ca href=\"\/products\/general-finishes-water-based-stain-cabernet-quart\"\u003eCabernet Quart\u003c\/a\u003e. Other colors in this size: \u003ca href=\"\/products\/general-finishes-water-based-stain-antique-brown-pint\"\u003eAntique Brown\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-antique-oak-pint\"\u003eAntique Oak\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-black-pint\"\u003eBlack\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-black-cherry-pint\"\u003eBlack Cherry\u003c\/a\u003e. Even out pine with \u003ca href=\"\/products\/general-finishes-pre-stain-conditioner-natural-pint\"\u003eGF Water-Based Pre-Stain Conditioner Natural\u003c\/a\u003e. Topcoat with \u003ca href=\"\/products\/general-finishes-high-performance-water-based-topcoat-clear-satin-quart\"\u003eGF High Performance Topcoat, Satin\u003c\/a\u003e or see all sheens in \u003ca href=\"\/collections\/general-finishes-high-performance\"\u003eHigh Performance Topcoat\u003c\/a\u003e. Prep with a \u003ca href=\"\/products\/3m-softback-contour-sanding-sponge-fine-4-1-2-inch\"\u003e3M Softback sanding sponge\u003c\/a\u003e. Browse every color in \u003ca href=\"\/collections\/general-finishes-water-based-wood-stain\"\u003eGF Water-Based Wood Stain\u003c\/a\u003e, compare \u003ca href=\"\/collections\/curated-wood-stains-gel-stains\"\u003ewood stains and gel stains\u003c\/a\u003e, or plan the job with the \u003ca href=\"\/pages\/furniture-refinishing-project-cart\"\u003efurniture refinishing project cart\u003c\/a\u003e or \u003ca href=\"\/pages\/paint-cabinets-project-cart\"\u003ecabinet project cart\u003c\/a\u003e.\u003c\/p\u003e","brand":"General Finishes","offers":[{"title":"Default Title","offer_id":67673250169142,"sku":"WZPT","price":25.16,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0931\/9750\/0726\/files\/606016103102.jpg?v=1792076220"},{"product_id":"general-finishes-water-based-stain-cabernet-quart","title":"General Finishes Water-Based Stain, Cabernet, Quart","description":"\u003cp\u003eGeneral Finishes Water-Based Wood Stain in Cabernet is a water-based pigmented stain for interior raw wood such as cabinets, trim, doors and furniture. General Finishes says its pigments give rich, dark, uniform color on hard-to-stain woods like maple and pine, and that it can also go over an existing finish, much like an oil-based gel stain. It is low odor, cleans up with water and is noncombustible. This is the quart (32 fl oz) can, GF item WZQT.\u003c\/p\u003e\n\u003ch3\u003eHighlights\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eOne coat is recommended; a second coat after the first is fully dry makes the color darker. GF says not to go past two coats.\u003c\/li\u003e\n\u003cli\u003eDry to the touch in 30 minutes; ready for a second coat or a water-based topcoat in 2 hours (70 F, 50% humidity). Wait 24 hours before an oil-based topcoat.\u003c\/li\u003e\n\u003cli\u003eBrush, foam brush, pad, microfiber roller or spray (HVLP 1.1-1.3 mm).\u003c\/li\u003e\n\u003cli\u003eStain gives color only; finish with 3 coats of a GF topcoat.\u003c\/li\u003e\n\u003cli\u003eThin with distilled water, starting at 5% and up to 10% by volume.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eBest for\u003c\/h3\u003e\n\u003cp\u003eIndoor cabinets, furniture, trim and doors, on raw wood or on a cleaned and scuff-sanded existing finish after an adhesion test. It is an interior stain; for outdoor wood, GF makes a separate Exterior 450 stain.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003eColor \/ size\u003c\/th\u003e\n\u003ctd\u003eCabernet \/ Quart (32 fl oz)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eGF item \/ UPC\u003c\/th\u003e\n\u003ctd\u003eWZQT \/ 606016103287\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eType\u003c\/th\u003e\n\u003ctd\u003eWater-based pigmented stain, interior\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoverage\u003c\/th\u003e\n\u003ctd\u003eUp to 600 sq ft per gallon (TDS), so up to about 150 sq ft for this can (calculated)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDry times\u003c\/th\u003e\n\u003ctd\u003eTouch 30 minutes; recoat 2 hours; 24 hours before an oil-based topcoat (70 F, 50% humidity; cool, humid or thick coats take longer)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoats\u003c\/th\u003e\n\u003ctd\u003e1 recommended, 2 maximum\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply with\u003c\/th\u003e\n\u003ctd\u003eSynthetic-bristle or foam brush, pad applicator, short-nap or foam roller, or spray. HVLP 1.1-1.3 mm; air-assist airless .007 in; airless fine finish .007-.009 in\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply when\u003c\/th\u003e\n\u003ctd\u003eAbout 70 F and 50% humidity, out of direct sun. GF Accelerator helps in cool or humid conditions, GF Extender in warm or dry ones.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThinning\u003c\/th\u003e\n\u003ctd\u003eDistilled water, 5% up to 10% by volume\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eClean up\u003c\/th\u003e\n\u003ctd\u003eSoap and water (hands); GF Brush \u0026amp; Gun Cleaner (equipment)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSolids\u003c\/th\u003e\n\u003ctd\u003e12-22% by volume, 14-20% by weight (varies by color)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVOC\u003c\/th\u003e\n\u003ctd\u003eUnder 145 g\/L on the Cabernet SDS (rev. 02-Feb-2024); the TDS says all colors are under 185 g\/L\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAir quality\u003c\/th\u003e\n\u003ctd\u003eSCAQMD, CARB, Canada, OTC Phase I and II compliant (TDS)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStorage\u003c\/th\u003e\n\u003ctd\u003e50-80 F, tightly sealed, out of sun; best used within a year of the date on the can\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSources\u003c\/th\u003e\n\u003ctd\u003e\n\u003ca href=\"https:\/\/generalfinishes.com\/wood-finishes-retail\/water-based-wood-stains-and-dye-stains\/water-based-wood-stain\" target=\"_blank\" rel=\"noopener\"\u003eGeneral Finishes Water-Based Wood Stain page\u003c\/a\u003e; \u003ca href=\"https:\/\/generalfinishes.com\/sites\/default\/files\/documents\/files\/2020-04\/TDS-2020-03-Water-Based-Wood-Stain-General-Finishes.pdf\" target=\"_blank\" rel=\"noopener\"\u003eTechnical data sheet (March 2020)\u003c\/a\u003e; \u003ca href=\"https:\/\/generalfinishes.com\/sites\/default\/files\/documents\/files\/2024-02\/SDS-English-Water-Based-Wood-Stain-CABERNET-Water-Base-General-Finishes-US-HCS-2012-v1-2024-02-02.PDF\" target=\"_blank\" rel=\"noopener\"\u003eCabernet SDS (rev. 02-Feb-2024)\u003c\/a\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\u003ch3\u003eHow much do I need?\u003c\/h3\u003e\n\u003cp\u003eGF rates the stain at up to 600 sq ft per gallon, so this quart covers up to about 150 sq ft (calculated). Porous or softer woods take more. If you plan a second coat, count it as another full pass.\u003c\/p\u003e\n\u003ch3\u003eHow to apply\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eRaw wood: sand with 120 grit, then 150 or 220 grit, and remove the dust. GF says no finer than 220 on closed-grain woods or 180 on open-grain woods. To reduce grain raise, wet the wood with water, let it dry and sand smooth before staining.\u003c\/li\u003e\n\u003cli\u003eExisting finish: scuff-clean with a non-woven pad and a 50:50 mix of denatured alcohol and water, dry 1-2 hours, then sand lightly with a 220-320 grit sponge. Remove dust and test adhesion.\u003c\/li\u003e\n\u003cli\u003eWork in a ventilated area and stir before and during use. On raw wood, apply a liberal amount to one section at a time, then wipe off the excess with the grain using absorbent terry cloth or paper towel. Do not use cotton T-shirts; they push the stain around. Correct lap marks right away by rewetting the whole section and wiping again.\u003c\/li\u003e\n\u003cli\u003eOver an existing finish, use thin coats with a foam brush or staining pad and avoid heavy build.\u003c\/li\u003e\n\u003cli\u003eLet it dry at least 2 hours (24 hours under an oil-based topcoat), then apply 3 coats of a GF topcoat. Take care not to sand through the first topcoat coat.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eGood to know\u003c\/h3\u003e\n\u003cp\u003eStain color changes with wood species, prep, lighting and the topcoat, so test the full stain-and-topcoat process on scrap first. On blotch-prone woods like pine, GF Water-Based Pre-Stain Conditioner Natural evens out color but limits how much stain soaks in, so a darker color may be needed. GF notes that California users who add more than 2% GF Extender make the stain non-compliant under SCAQMD rules. The Cabernet SDS (rev. 02-Feb-2024) lists the mixture as not classified, with no signal word. Use the respirator GF specifies when spraying. Store between 50 and 80 F and do not pour leftovers down the drain.\u003c\/p\u003e\n\u003ch3\u003eQuestions\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eCan I use it over a finished cabinet?\u003c\/strong\u003e Yes, after cleaning, scuff-sanding and an adhesion test, using thin coats like a gel stain.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCan I put an oil-based polyurethane over it?\u003c\/strong\u003e Yes. GF says to let the stain dry 24 hours first. Oil-based topcoats can amber, so test the look.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDoes it need a topcoat?\u003c\/strong\u003e Yes. GF says the stain provides color but is not durable on its own; finish with 3 coats of a GF topcoat.\u003c\/p\u003e\n\u003ch3\u003eShop related\u003c\/h3\u003e\n\u003cp\u003eSame color, other size: \u003ca href=\"\/products\/general-finishes-water-based-stain-cabernet-pint\"\u003eCabernet Pint\u003c\/a\u003e. Other colors in this size: \u003ca href=\"\/products\/general-finishes-water-based-stain-antique-brown-quart\"\u003eAntique Brown\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-antique-oak-quart\"\u003eAntique Oak\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-black-quart\"\u003eBlack\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-black-cherry-quart\"\u003eBlack Cherry\u003c\/a\u003e. Even out pine with \u003ca href=\"\/products\/general-finishes-pre-stain-conditioner-natural-quart\"\u003eGF Water-Based Pre-Stain Conditioner Natural\u003c\/a\u003e. Topcoat with \u003ca href=\"\/products\/general-finishes-high-performance-water-based-topcoat-clear-satin-quart\"\u003eGF High Performance Topcoat, Satin\u003c\/a\u003e or see all sheens in \u003ca href=\"\/collections\/general-finishes-high-performance\"\u003eHigh Performance Topcoat\u003c\/a\u003e. Prep with a \u003ca href=\"\/products\/3m-softback-contour-sanding-sponge-fine-4-1-2-inch\"\u003e3M Softback sanding sponge\u003c\/a\u003e. Browse every color in \u003ca href=\"\/collections\/general-finishes-water-based-wood-stain\"\u003eGF Water-Based Wood Stain\u003c\/a\u003e, compare \u003ca href=\"\/collections\/curated-wood-stains-gel-stains\"\u003ewood stains and gel stains\u003c\/a\u003e, or plan the job with the \u003ca href=\"\/pages\/furniture-refinishing-project-cart\"\u003efurniture refinishing project cart\u003c\/a\u003e or \u003ca href=\"\/pages\/paint-cabinets-project-cart\"\u003ecabinet project cart\u003c\/a\u003e.\u003c\/p\u003e","brand":"General Finishes","offers":[{"title":"Default Title","offer_id":67673250234678,"sku":"WZQT","price":39.46,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0931\/9750\/0726\/files\/606016103287.jpg?v=1791581980"},{"product_id":"general-finishes-water-based-stain-graystone-pint","title":"General Finishes Water-Based Stain, Graystone, Pint","description":"\u003cp\u003eGeneral Finishes Water-Based Wood Stain in Graystone is a water-based pigmented stain for interior raw wood such as cabinets, trim, doors and furniture. General Finishes says its pigments give rich, dark, uniform color on hard-to-stain woods like maple and pine, and that it can also go over an existing finish, much like an oil-based gel stain. It is low odor, cleans up with water and is noncombustible. This is the pint (16 fl oz) can, GF item WQPT.\u003c\/p\u003e\n\u003ch3\u003eHighlights\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eOne coat is recommended; a second coat after the first is fully dry makes the color darker. GF says not to go past two coats.\u003c\/li\u003e\n\u003cli\u003eDry to the touch in 30 minutes; ready for a second coat or a water-based topcoat in 2 hours (70 F, 50% humidity). Wait 24 hours before an oil-based topcoat.\u003c\/li\u003e\n\u003cli\u003eBrush, foam brush, pad, microfiber roller or spray (HVLP 1.1-1.3 mm).\u003c\/li\u003e\n\u003cli\u003eStain gives color only; finish with 3 coats of a GF topcoat.\u003c\/li\u003e\n\u003cli\u003eThin with distilled water, starting at 5% and up to 10% by volume.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eBest for\u003c\/h3\u003e\n\u003cp\u003eIndoor cabinets, furniture, trim and doors, on raw wood or on a cleaned and scuff-sanded existing finish after an adhesion test. It is an interior stain; for outdoor wood, GF makes a separate Exterior 450 stain.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003eColor \/ size\u003c\/th\u003e\n\u003ctd\u003eGraystone \/ Pint (16 fl oz)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eGF item \/ UPC\u003c\/th\u003e\n\u003ctd\u003eWQPT \/ 606016103010\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eType\u003c\/th\u003e\n\u003ctd\u003eWater-based pigmented stain, interior\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoverage\u003c\/th\u003e\n\u003ctd\u003eUp to 600 sq ft per gallon (TDS), so up to about 75 sq ft for this can (calculated)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDry times\u003c\/th\u003e\n\u003ctd\u003eTouch 30 minutes; recoat 2 hours; 24 hours before an oil-based topcoat (70 F, 50% humidity; cool, humid or thick coats take longer)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoats\u003c\/th\u003e\n\u003ctd\u003e1 recommended, 2 maximum\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply with\u003c\/th\u003e\n\u003ctd\u003eSynthetic-bristle or foam brush, pad applicator, short-nap or foam roller, or spray. HVLP 1.1-1.3 mm; air-assist airless .007 in; airless fine finish .007-.009 in\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply when\u003c\/th\u003e\n\u003ctd\u003eAbout 70 F and 50% humidity, out of direct sun. GF Accelerator helps in cool or humid conditions, GF Extender in warm or dry ones.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThinning\u003c\/th\u003e\n\u003ctd\u003eDistilled water, 5% up to 10% by volume\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eClean up\u003c\/th\u003e\n\u003ctd\u003eSoap and water (hands); GF Brush \u0026amp; Gun Cleaner (equipment)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSolids\u003c\/th\u003e\n\u003ctd\u003e12-22% by volume, 14-20% by weight (varies by color)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVOC\u003c\/th\u003e\n\u003ctd\u003e135 g\/L on the Graystone SDS; the TDS says all colors are under 185 g\/L\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAir quality\u003c\/th\u003e\n\u003ctd\u003eSCAQMD, CARB, Canada, OTC Phase I and II compliant (TDS)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStorage\u003c\/th\u003e\n\u003ctd\u003e50-80 F, tightly sealed, out of sun; best used within a year of the date on the can\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSources\u003c\/th\u003e\n\u003ctd\u003e\n\u003ca href=\"https:\/\/generalfinishes.com\/wood-finishes-retail\/water-based-wood-stains-and-dye-stains\/water-based-wood-stain\" target=\"_blank\" rel=\"noopener\"\u003eGeneral Finishes Water-Based Wood Stain page\u003c\/a\u003e; \u003ca href=\"https:\/\/generalfinishes.com\/sites\/default\/files\/documents\/files\/2020-04\/TDS-2020-03-Water-Based-Wood-Stain-General-Finishes.pdf\" target=\"_blank\" rel=\"noopener\"\u003eTechnical data sheet (March 2020)\u003c\/a\u003e; \u003ca href=\"https:\/\/generalfinishes.com\/sites\/default\/files\/documents\/files\/2024-02\/SDS-English-Water-Based-Wood-Stain-GRAYSTONE-Water-Base-General-Finishes-US-HCS-2012-v1-2024-02-02.PDF\" target=\"_blank\" rel=\"noopener\"\u003eGraystone SDS (rev. 02-Feb-2024)\u003c\/a\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\u003ch3\u003eHow much do I need?\u003c\/h3\u003e\n\u003cp\u003eGF rates the stain at up to 600 sq ft per gallon, so this pint covers up to about 75 sq ft (calculated). Porous or softer woods take more. If you plan a second coat, count it as another full pass.\u003c\/p\u003e\n\u003ch3\u003eHow to apply\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eRaw wood: sand with 120 grit, then 150 or 220 grit, and remove the dust. GF says no finer than 220 on closed-grain woods or 180 on open-grain woods. To reduce grain raise, wet the wood with water, let it dry and sand smooth before staining.\u003c\/li\u003e\n\u003cli\u003eExisting finish: scuff-clean with a non-woven pad and a 50:50 mix of denatured alcohol and water, dry 1-2 hours, then sand lightly with a 220-320 grit sponge. Remove dust and test adhesion.\u003c\/li\u003e\n\u003cli\u003eWork in a ventilated area and stir before and during use. On raw wood, apply a liberal amount to one section at a time, then wipe off the excess with the grain using absorbent terry cloth or paper towel. Do not use cotton T-shirts; they push the stain around. Correct lap marks right away by rewetting the whole section and wiping again.\u003c\/li\u003e\n\u003cli\u003eOver an existing finish, use thin coats with a foam brush or staining pad and avoid heavy build.\u003c\/li\u003e\n\u003cli\u003eLet it dry at least 2 hours (24 hours under an oil-based topcoat), then apply 3 coats of a GF topcoat. Take care not to sand through the first topcoat coat.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eGood to know\u003c\/h3\u003e\n\u003cp\u003eStain color changes with wood species, prep, lighting and the topcoat, so test the full stain-and-topcoat process on scrap first. On blotch-prone woods like pine, GF Water-Based Pre-Stain Conditioner Natural evens out color but limits how much stain soaks in, so a darker color may be needed. GF notes that California users who add more than 2% GF Extender make the stain non-compliant under SCAQMD rules. The Graystone SDS (rev. 02-Feb-2024) uses the signal word Warning: suspected of causing cancer. Wear the protection it lists, and use the respirator GF specifies when spraying. Store between 50 and 80 F and do not pour leftovers down the drain.\u003c\/p\u003e\n\u003ch3\u003eQuestions\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eCan I use it over a finished cabinet?\u003c\/strong\u003e Yes, after cleaning, scuff-sanding and an adhesion test, using thin coats like a gel stain.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCan I put an oil-based polyurethane over it?\u003c\/strong\u003e Yes. GF says to let the stain dry 24 hours first. Oil-based topcoats can amber, so test the look.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDoes it need a topcoat?\u003c\/strong\u003e Yes. GF says the stain provides color but is not durable on its own; finish with 3 coats of a GF topcoat.\u003c\/p\u003e\n\u003ch3\u003eShop related\u003c\/h3\u003e\n\u003cp\u003eSame color, other size: \u003ca href=\"\/products\/general-finishes-water-based-stain-graystone-quart\"\u003eGraystone Quart\u003c\/a\u003e. Other colors in this size: \u003ca href=\"\/products\/general-finishes-water-based-stain-antique-brown-pint\"\u003eAntique Brown\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-black-pint\"\u003eBlack\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-espresso-pint\"\u003eEspresso\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-walnut-pint\"\u003eWalnut\u003c\/a\u003e. Even out pine with \u003ca href=\"\/products\/general-finishes-pre-stain-conditioner-natural-pint\"\u003eGF Water-Based Pre-Stain Conditioner Natural\u003c\/a\u003e. Topcoat with \u003ca href=\"\/products\/general-finishes-high-performance-water-based-topcoat-clear-satin-quart\"\u003eGF High Performance Topcoat, Satin\u003c\/a\u003e or see all sheens in \u003ca href=\"\/collections\/general-finishes-high-performance\"\u003eHigh Performance Topcoat\u003c\/a\u003e. Prep with a \u003ca href=\"\/products\/3m-softback-contour-sanding-sponge-fine-4-1-2-inch\"\u003e3M Softback sanding sponge\u003c\/a\u003e. Browse every color in \u003ca href=\"\/collections\/general-finishes-water-based-wood-stain\"\u003eGF Water-Based Wood Stain\u003c\/a\u003e, compare \u003ca href=\"\/collections\/curated-wood-stains-gel-stains\"\u003ewood stains and gel stains\u003c\/a\u003e, or plan the job with the \u003ca href=\"\/pages\/furniture-refinishing-project-cart\"\u003efurniture refinishing project cart\u003c\/a\u003e or \u003ca href=\"\/pages\/paint-cabinets-project-cart\"\u003ecabinet project cart\u003c\/a\u003e.\u003c\/p\u003e","brand":"General Finishes","offers":[{"title":"Default Title","offer_id":67673250267446,"sku":"WQPT","price":25.16,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0931\/9750\/0726\/files\/606016103010.jpg?v=1791730293"},{"product_id":"general-finishes-water-based-stain-graystone-quart","title":"General Finishes Water-Based Stain, Graystone, Quart","description":"\u003cp\u003eGeneral Finishes Water-Based Wood Stain in Graystone is a water-based pigmented stain for interior raw wood such as cabinets, trim, doors and furniture. General Finishes says its pigments give rich, dark, uniform color on hard-to-stain woods like maple and pine, and that it can also go over an existing finish, much like an oil-based gel stain. It is low odor, cleans up with water and is noncombustible. This is the quart (32 fl oz) can, GF item WQQT.\u003c\/p\u003e\n\u003ch3\u003eHighlights\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eOne coat is recommended; a second coat after the first is fully dry makes the color darker. GF says not to go past two coats.\u003c\/li\u003e\n\u003cli\u003eDry to the touch in 30 minutes; ready for a second coat or a water-based topcoat in 2 hours (70 F, 50% humidity). Wait 24 hours before an oil-based topcoat.\u003c\/li\u003e\n\u003cli\u003eBrush, foam brush, pad, microfiber roller or spray (HVLP 1.1-1.3 mm).\u003c\/li\u003e\n\u003cli\u003eStain gives color only; finish with 3 coats of a GF topcoat.\u003c\/li\u003e\n\u003cli\u003eThin with distilled water, starting at 5% and up to 10% by volume.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eBest for\u003c\/h3\u003e\n\u003cp\u003eIndoor cabinets, furniture, trim and doors, on raw wood or on a cleaned and scuff-sanded existing finish after an adhesion test. It is an interior stain; for outdoor wood, GF makes a separate Exterior 450 stain.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003eColor \/ size\u003c\/th\u003e\n\u003ctd\u003eGraystone \/ Quart (32 fl oz)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eGF item \/ UPC\u003c\/th\u003e\n\u003ctd\u003eWQQT \/ 606016103195\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eType\u003c\/th\u003e\n\u003ctd\u003eWater-based pigmented stain, interior\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoverage\u003c\/th\u003e\n\u003ctd\u003eUp to 600 sq ft per gallon (TDS), so up to about 150 sq ft for this can (calculated)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDry times\u003c\/th\u003e\n\u003ctd\u003eTouch 30 minutes; recoat 2 hours; 24 hours before an oil-based topcoat (70 F, 50% humidity; cool, humid or thick coats take longer)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoats\u003c\/th\u003e\n\u003ctd\u003e1 recommended, 2 maximum\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply with\u003c\/th\u003e\n\u003ctd\u003eSynthetic-bristle or foam brush, pad applicator, short-nap or foam roller, or spray. HVLP 1.1-1.3 mm; air-assist airless .007 in; airless fine finish .007-.009 in\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply when\u003c\/th\u003e\n\u003ctd\u003eAbout 70 F and 50% humidity, out of direct sun. GF Accelerator helps in cool or humid conditions, GF Extender in warm or dry ones.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThinning\u003c\/th\u003e\n\u003ctd\u003eDistilled water, 5% up to 10% by volume\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eClean up\u003c\/th\u003e\n\u003ctd\u003eSoap and water (hands); GF Brush \u0026amp; Gun Cleaner (equipment)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSolids\u003c\/th\u003e\n\u003ctd\u003e12-22% by volume, 14-20% by weight (varies by color)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVOC\u003c\/th\u003e\n\u003ctd\u003e135 g\/L on the Graystone SDS; the TDS says all colors are under 185 g\/L\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAir quality\u003c\/th\u003e\n\u003ctd\u003eSCAQMD, CARB, Canada, OTC Phase I and II compliant (TDS)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStorage\u003c\/th\u003e\n\u003ctd\u003e50-80 F, tightly sealed, out of sun; best used within a year of the date on the can\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSources\u003c\/th\u003e\n\u003ctd\u003e\n\u003ca href=\"https:\/\/generalfinishes.com\/wood-finishes-retail\/water-based-wood-stains-and-dye-stains\/water-based-wood-stain\" target=\"_blank\" rel=\"noopener\"\u003eGeneral Finishes Water-Based Wood Stain page\u003c\/a\u003e; \u003ca href=\"https:\/\/generalfinishes.com\/sites\/default\/files\/documents\/files\/2020-04\/TDS-2020-03-Water-Based-Wood-Stain-General-Finishes.pdf\" target=\"_blank\" rel=\"noopener\"\u003eTechnical data sheet (March 2020)\u003c\/a\u003e; \u003ca href=\"https:\/\/generalfinishes.com\/sites\/default\/files\/documents\/files\/2024-02\/SDS-English-Water-Based-Wood-Stain-GRAYSTONE-Water-Base-General-Finishes-US-HCS-2012-v1-2024-02-02.PDF\" target=\"_blank\" rel=\"noopener\"\u003eGraystone SDS (rev. 02-Feb-2024)\u003c\/a\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\u003ch3\u003eHow much do I need?\u003c\/h3\u003e\n\u003cp\u003eGF rates the stain at up to 600 sq ft per gallon, so this quart covers up to about 150 sq ft (calculated). Porous or softer woods take more. If you plan a second coat, count it as another full pass.\u003c\/p\u003e\n\u003ch3\u003eHow to apply\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eRaw wood: sand with 120 grit, then 150 or 220 grit, and remove the dust. GF says no finer than 220 on closed-grain woods or 180 on open-grain woods. To reduce grain raise, wet the wood with water, let it dry and sand smooth before staining.\u003c\/li\u003e\n\u003cli\u003eExisting finish: scuff-clean with a non-woven pad and a 50:50 mix of denatured alcohol and water, dry 1-2 hours, then sand lightly with a 220-320 grit sponge. Remove dust and test adhesion.\u003c\/li\u003e\n\u003cli\u003eWork in a ventilated area and stir before and during use. On raw wood, apply a liberal amount to one section at a time, then wipe off the excess with the grain using absorbent terry cloth or paper towel. Do not use cotton T-shirts; they push the stain around. Correct lap marks right away by rewetting the whole section and wiping again.\u003c\/li\u003e\n\u003cli\u003eOver an existing finish, use thin coats with a foam brush or staining pad and avoid heavy build.\u003c\/li\u003e\n\u003cli\u003eLet it dry at least 2 hours (24 hours under an oil-based topcoat), then apply 3 coats of a GF topcoat. Take care not to sand through the first topcoat coat.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eGood to know\u003c\/h3\u003e\n\u003cp\u003eStain color changes with wood species, prep, lighting and the topcoat, so test the full stain-and-topcoat process on scrap first. On blotch-prone woods like pine, GF Water-Based Pre-Stain Conditioner Natural evens out color but limits how much stain soaks in, so a darker color may be needed. GF notes that California users who add more than 2% GF Extender make the stain non-compliant under SCAQMD rules. The Graystone SDS (rev. 02-Feb-2024) uses the signal word Warning: suspected of causing cancer. Wear the protection it lists, and use the respirator GF specifies when spraying. Store between 50 and 80 F and do not pour leftovers down the drain.\u003c\/p\u003e\n\u003ch3\u003eQuestions\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eCan I use it over a finished cabinet?\u003c\/strong\u003e Yes, after cleaning, scuff-sanding and an adhesion test, using thin coats like a gel stain.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCan I put an oil-based polyurethane over it?\u003c\/strong\u003e Yes. GF says to let the stain dry 24 hours first. Oil-based topcoats can amber, so test the look.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDoes it need a topcoat?\u003c\/strong\u003e Yes. GF says the stain provides color but is not durable on its own; finish with 3 coats of a GF topcoat.\u003c\/p\u003e\n\u003ch3\u003eShop related\u003c\/h3\u003e\n\u003cp\u003eSame color, other size: \u003ca href=\"\/products\/general-finishes-water-based-stain-graystone-pint\"\u003eGraystone Pint\u003c\/a\u003e. Other colors in this size: \u003ca href=\"\/products\/general-finishes-water-based-stain-antique-brown-quart\"\u003eAntique Brown\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-black-quart\"\u003eBlack\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-espresso-quart\"\u003eEspresso\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-walnut-quart\"\u003eWalnut\u003c\/a\u003e. Even out pine with \u003ca href=\"\/products\/general-finishes-pre-stain-conditioner-natural-quart\"\u003eGF Water-Based Pre-Stain Conditioner Natural\u003c\/a\u003e. Topcoat with \u003ca href=\"\/products\/general-finishes-high-performance-water-based-topcoat-clear-satin-quart\"\u003eGF High Performance Topcoat, Satin\u003c\/a\u003e or see all sheens in \u003ca href=\"\/collections\/general-finishes-high-performance\"\u003eHigh Performance Topcoat\u003c\/a\u003e. Prep with a \u003ca href=\"\/products\/3m-softback-contour-sanding-sponge-fine-4-1-2-inch\"\u003e3M Softback sanding sponge\u003c\/a\u003e. Browse every color in \u003ca href=\"\/collections\/general-finishes-water-based-wood-stain\"\u003eGF Water-Based Wood Stain\u003c\/a\u003e, compare \u003ca href=\"\/collections\/curated-wood-stains-gel-stains\"\u003ewood stains and gel stains\u003c\/a\u003e, or plan the job with the \u003ca href=\"\/pages\/furniture-refinishing-project-cart\"\u003efurniture refinishing project cart\u003c\/a\u003e or \u003ca href=\"\/pages\/paint-cabinets-project-cart\"\u003ecabinet project cart\u003c\/a\u003e.\u003c\/p\u003e","brand":"General Finishes","offers":[{"title":"Default Title","offer_id":67673250398518,"sku":"WQQT","price":39.46,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0931\/9750\/0726\/files\/606016103195.jpg?v=1791581984"},{"product_id":"general-finishes-water-based-stain-graphite-quart","title":"General Finishes Water-Based Stain, Graphite, Quart","description":"\u003cp\u003eGeneral Finishes Water-Based Wood Stain in Graphite is a water-based pigmented stain for interior raw wood such as cabinets, trim, doors and furniture. General Finishes says its pigments give rich, dark, uniform color on hard-to-stain woods like maple and pine, and that it can also go over an existing finish, much like an oil-based gel stain. It is low odor, cleans up with water and is noncombustible. This is the quart (32 fl oz) can, GF item WJQT.\u003c\/p\u003e\n\u003ch3\u003eHighlights\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eOne coat is recommended; a second coat after the first is fully dry makes the color darker. GF says not to go past two coats.\u003c\/li\u003e\n\u003cli\u003eDry to the touch in 30 minutes; ready for a second coat or a water-based topcoat in 2 hours (70 F, 50% humidity). Wait 24 hours before an oil-based topcoat.\u003c\/li\u003e\n\u003cli\u003eBrush, foam brush, pad, microfiber roller or spray (HVLP 1.1-1.3 mm).\u003c\/li\u003e\n\u003cli\u003eStain gives color only; finish with 3 coats of a GF topcoat.\u003c\/li\u003e\n\u003cli\u003eThin with distilled water, starting at 5% and up to 10% by volume.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eBest for\u003c\/h3\u003e\n\u003cp\u003eIndoor cabinets, furniture, trim and doors, on raw wood or on a cleaned and scuff-sanded existing finish after an adhesion test. It is an interior stain; for outdoor wood, GF makes a separate Exterior 450 stain.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003eColor \/ size\u003c\/th\u003e\n\u003ctd\u003eGraphite \/ Quart (32 fl oz)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eGF item \/ UPC\u003c\/th\u003e\n\u003ctd\u003eWJQT \/ 606016103201\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eType\u003c\/th\u003e\n\u003ctd\u003eWater-based pigmented stain, interior\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoverage\u003c\/th\u003e\n\u003ctd\u003eUp to 600 sq ft per gallon (TDS), so up to about 150 sq ft for this can (calculated)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDry times\u003c\/th\u003e\n\u003ctd\u003eTouch 30 minutes; recoat 2 hours; 24 hours before an oil-based topcoat (70 F, 50% humidity; cool, humid or thick coats take longer)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoats\u003c\/th\u003e\n\u003ctd\u003e1 recommended, 2 maximum\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply with\u003c\/th\u003e\n\u003ctd\u003eSynthetic-bristle or foam brush, pad applicator, short-nap or foam roller, or spray. HVLP 1.1-1.3 mm; air-assist airless .007 in; airless fine finish .007-.009 in\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply when\u003c\/th\u003e\n\u003ctd\u003eAbout 70 F and 50% humidity, out of direct sun. GF Accelerator helps in cool or humid conditions, GF Extender in warm or dry ones.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThinning\u003c\/th\u003e\n\u003ctd\u003eDistilled water, 5% up to 10% by volume\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eClean up\u003c\/th\u003e\n\u003ctd\u003eSoap and water (hands); GF Brush \u0026amp; Gun Cleaner (equipment)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSolids\u003c\/th\u003e\n\u003ctd\u003e12-22% by volume, 14-20% by weight (varies by color)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVOC\u003c\/th\u003e\n\u003ctd\u003eUnder 135 g\/L on the Graphite SDS (rev. 02-Feb-2024); the TDS says all colors are under 185 g\/L\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAir quality\u003c\/th\u003e\n\u003ctd\u003eSCAQMD, CARB, Canada, OTC Phase I and II compliant (TDS)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStorage\u003c\/th\u003e\n\u003ctd\u003e50-80 F, tightly sealed, out of sun; best used within a year of the date on the can\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSources\u003c\/th\u003e\n\u003ctd\u003e\n\u003ca href=\"https:\/\/generalfinishes.com\/wood-finishes-retail\/water-based-wood-stains-and-dye-stains\/water-based-wood-stain\" target=\"_blank\" rel=\"noopener\"\u003eGeneral Finishes Water-Based Wood Stain page\u003c\/a\u003e; \u003ca href=\"https:\/\/generalfinishes.com\/sites\/default\/files\/documents\/files\/2020-04\/TDS-2020-03-Water-Based-Wood-Stain-General-Finishes.pdf\" target=\"_blank\" rel=\"noopener\"\u003eTechnical data sheet (March 2020)\u003c\/a\u003e; \u003ca href=\"https:\/\/generalfinishes.com\/sites\/default\/files\/documents\/files\/2024-02\/SDS-English-Water-Based-Wood-Stain-GRAPHITE-Water-Base-General-Finishes-US-HCS-2012-v1-2024-02-02.PDF\" target=\"_blank\" rel=\"noopener\"\u003eGraphite SDS (rev. 02-Feb-2024)\u003c\/a\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\u003ch3\u003eHow much do I need?\u003c\/h3\u003e\n\u003cp\u003eGF rates the stain at up to 600 sq ft per gallon, so this quart covers up to about 150 sq ft (calculated). Porous or softer woods take more. If you plan a second coat, count it as another full pass.\u003c\/p\u003e\n\u003ch3\u003eHow to apply\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eRaw wood: sand with 120 grit, then 150 or 220 grit, and remove the dust. GF says no finer than 220 on closed-grain woods or 180 on open-grain woods. To reduce grain raise, wet the wood with water, let it dry and sand smooth before staining.\u003c\/li\u003e\n\u003cli\u003eExisting finish: scuff-clean with a non-woven pad and a 50:50 mix of denatured alcohol and water, dry 1-2 hours, then sand lightly with a 220-320 grit sponge. Remove dust and test adhesion.\u003c\/li\u003e\n\u003cli\u003eWork in a ventilated area and stir before and during use. On raw wood, apply a liberal amount to one section at a time, then wipe off the excess with the grain using absorbent terry cloth or paper towel. Do not use cotton T-shirts; they push the stain around. Correct lap marks right away by rewetting the whole section and wiping again.\u003c\/li\u003e\n\u003cli\u003eOver an existing finish, use thin coats with a foam brush or staining pad and avoid heavy build.\u003c\/li\u003e\n\u003cli\u003eLet it dry at least 2 hours (24 hours under an oil-based topcoat), then apply 3 coats of a GF topcoat. Take care not to sand through the first topcoat coat.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eGood to know\u003c\/h3\u003e\n\u003cp\u003eStain color changes with wood species, prep, lighting and the topcoat, so test the full stain-and-topcoat process on scrap first. On blotch-prone woods like pine, GF Water-Based Pre-Stain Conditioner Natural evens out color but limits how much stain soaks in, so a darker color may be needed. GF notes that California users who add more than 2% GF Extender make the stain non-compliant under SCAQMD rules. The Graphite SDS (rev. 02-Feb-2024) uses the signal word Danger: may cause cancer. Wear the protection it lists, and use the respirator GF specifies when spraying. Store between 50 and 80 F and do not pour leftovers down the drain.\u003c\/p\u003e\n\u003ch3\u003eQuestions\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eCan I use it over a finished cabinet?\u003c\/strong\u003e Yes, after cleaning, scuff-sanding and an adhesion test, using thin coats like a gel stain.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCan I put an oil-based polyurethane over it?\u003c\/strong\u003e Yes. GF says to let the stain dry 24 hours first. Oil-based topcoats can amber, so test the look.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDoes it need a topcoat?\u003c\/strong\u003e Yes. GF says the stain provides color but is not durable on its own; finish with 3 coats of a GF topcoat.\u003c\/p\u003e\n\u003ch3\u003eShop related\u003c\/h3\u003e\n\u003cp\u003eOther colors in this size: \u003ca href=\"\/products\/general-finishes-water-based-stain-antique-brown-quart\"\u003eAntique Brown\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-antique-oak-quart\"\u003eAntique Oak\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-black-quart\"\u003eBlack\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-black-cherry-quart\"\u003eBlack Cherry\u003c\/a\u003e. Even out pine with \u003ca href=\"\/products\/general-finishes-pre-stain-conditioner-natural-quart\"\u003eGF Water-Based Pre-Stain Conditioner Natural\u003c\/a\u003e. Topcoat with \u003ca href=\"\/products\/general-finishes-high-performance-water-based-topcoat-clear-satin-quart\"\u003eGF High Performance Topcoat, Satin\u003c\/a\u003e or see all sheens in \u003ca href=\"\/collections\/general-finishes-high-performance\"\u003eHigh Performance Topcoat\u003c\/a\u003e. Prep with a \u003ca href=\"\/products\/3m-softback-contour-sanding-sponge-fine-4-1-2-inch\"\u003e3M Softback sanding sponge\u003c\/a\u003e. Browse every color in \u003ca href=\"\/collections\/general-finishes-water-based-wood-stain\"\u003eGF Water-Based Wood Stain\u003c\/a\u003e, compare \u003ca href=\"\/collections\/curated-wood-stains-gel-stains\"\u003ewood stains and gel stains\u003c\/a\u003e, or plan the job with the \u003ca href=\"\/pages\/furniture-refinishing-project-cart\"\u003efurniture refinishing project cart\u003c\/a\u003e or \u003ca href=\"\/pages\/paint-cabinets-project-cart\"\u003ecabinet project cart\u003c\/a\u003e.\u003c\/p\u003e","brand":"General Finishes","offers":[{"title":"Default Title","offer_id":67673250431286,"sku":"WJQT","price":39.46,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0931\/9750\/0726\/files\/606016103201.jpg?v=1791581986"},{"product_id":"general-finishes-water-based-stain-hickory-pint","title":"General Finishes Water-Based Stain, Hickory, Pint","description":"\u003cp\u003eGeneral Finishes Water-Based Wood Stain in Hickory is a water-based pigmented stain for interior raw wood such as cabinets, trim, doors and furniture. General Finishes says its pigments give rich, dark, uniform color on hard-to-stain woods like maple and pine, and that it can also go over an existing finish, much like an oil-based gel stain. It is low odor, cleans up with water and is noncombustible. This is the pint (16 fl oz) can, GF item WHPT.\u003c\/p\u003e\n\u003ch3\u003eHighlights\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eOne coat is recommended; a second coat after the first is fully dry makes the color darker. GF says not to go past two coats.\u003c\/li\u003e\n\u003cli\u003eDry to the touch in 30 minutes; ready for a second coat or a water-based topcoat in 2 hours (70 F, 50% humidity). Wait 24 hours before an oil-based topcoat.\u003c\/li\u003e\n\u003cli\u003eBrush, foam brush, pad, microfiber roller or spray (HVLP 1.1-1.3 mm).\u003c\/li\u003e\n\u003cli\u003eStain gives color only; finish with 3 coats of a GF topcoat.\u003c\/li\u003e\n\u003cli\u003eThin with distilled water, starting at 5% and up to 10% by volume.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eBest for\u003c\/h3\u003e\n\u003cp\u003eIndoor cabinets, furniture, trim and doors, on raw wood or on a cleaned and scuff-sanded existing finish after an adhesion test. It is an interior stain; for outdoor wood, GF makes a separate Exterior 450 stain.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003eColor \/ size\u003c\/th\u003e\n\u003ctd\u003eHickory \/ Pint (16 fl oz)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eGF item \/ UPC\u003c\/th\u003e\n\u003ctd\u003eWHPT \/ 606016103072\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eType\u003c\/th\u003e\n\u003ctd\u003eWater-based pigmented stain, interior\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoverage\u003c\/th\u003e\n\u003ctd\u003eUp to 600 sq ft per gallon (TDS), so up to about 75 sq ft for this can (calculated)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDry times\u003c\/th\u003e\n\u003ctd\u003eTouch 30 minutes; recoat 2 hours; 24 hours before an oil-based topcoat (70 F, 50% humidity; cool, humid or thick coats take longer)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoats\u003c\/th\u003e\n\u003ctd\u003e1 recommended, 2 maximum\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply with\u003c\/th\u003e\n\u003ctd\u003eSynthetic-bristle or foam brush, pad applicator, short-nap or foam roller, or spray. HVLP 1.1-1.3 mm; air-assist airless .007 in; airless fine finish .007-.009 in\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply when\u003c\/th\u003e\n\u003ctd\u003eAbout 70 F and 50% humidity, out of direct sun. GF Accelerator helps in cool or humid conditions, GF Extender in warm or dry ones.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThinning\u003c\/th\u003e\n\u003ctd\u003eDistilled water, 5% up to 10% by volume\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eClean up\u003c\/th\u003e\n\u003ctd\u003eSoap and water (hands); GF Brush \u0026amp; Gun Cleaner (equipment)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSolids\u003c\/th\u003e\n\u003ctd\u003e12-22% by volume, 14-20% by weight (varies by color)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVOC\u003c\/th\u003e\n\u003ctd\u003eUnder 165 g\/L on the Hickory SDS (rev. 02-Feb-2024); the TDS says all colors are under 185 g\/L\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAir quality\u003c\/th\u003e\n\u003ctd\u003eSCAQMD, CARB, Canada, OTC Phase I and II compliant (TDS)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStorage\u003c\/th\u003e\n\u003ctd\u003e50-80 F, tightly sealed, out of sun; best used within a year of the date on the can\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSources\u003c\/th\u003e\n\u003ctd\u003e\n\u003ca href=\"https:\/\/generalfinishes.com\/wood-finishes-retail\/water-based-wood-stains-and-dye-stains\/water-based-wood-stain\" target=\"_blank\" rel=\"noopener\"\u003eGeneral Finishes Water-Based Wood Stain page\u003c\/a\u003e; \u003ca href=\"https:\/\/generalfinishes.com\/sites\/default\/files\/documents\/files\/2020-04\/TDS-2020-03-Water-Based-Wood-Stain-General-Finishes.pdf\" target=\"_blank\" rel=\"noopener\"\u003eTechnical data sheet (March 2020)\u003c\/a\u003e; \u003ca href=\"https:\/\/generalfinishes.com\/sites\/default\/files\/documents\/files\/2024-02\/SDS-English-Water-Based-Wood-Stain-HICKORY-Water-Base-General-Finishes-US-HCS-2012-v1-2024-02-02.PDF\" target=\"_blank\" rel=\"noopener\"\u003eHickory SDS (rev. 02-Feb-2024)\u003c\/a\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\u003ch3\u003eHow much do I need?\u003c\/h3\u003e\n\u003cp\u003eGF rates the stain at up to 600 sq ft per gallon, so this pint covers up to about 75 sq ft (calculated). Porous or softer woods take more. If you plan a second coat, count it as another full pass.\u003c\/p\u003e\n\u003ch3\u003eHow to apply\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eRaw wood: sand with 120 grit, then 150 or 220 grit, and remove the dust. GF says no finer than 220 on closed-grain woods or 180 on open-grain woods. To reduce grain raise, wet the wood with water, let it dry and sand smooth before staining.\u003c\/li\u003e\n\u003cli\u003eExisting finish: scuff-clean with a non-woven pad and a 50:50 mix of denatured alcohol and water, dry 1-2 hours, then sand lightly with a 220-320 grit sponge. Remove dust and test adhesion.\u003c\/li\u003e\n\u003cli\u003eWork in a ventilated area and stir before and during use. On raw wood, apply a liberal amount to one section at a time, then wipe off the excess with the grain using absorbent terry cloth or paper towel. Do not use cotton T-shirts; they push the stain around. Correct lap marks right away by rewetting the whole section and wiping again.\u003c\/li\u003e\n\u003cli\u003eOver an existing finish, use thin coats with a foam brush or staining pad and avoid heavy build.\u003c\/li\u003e\n\u003cli\u003eLet it dry at least 2 hours (24 hours under an oil-based topcoat), then apply 3 coats of a GF topcoat. Take care not to sand through the first topcoat coat.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eGood to know\u003c\/h3\u003e\n\u003cp\u003eStain color changes with wood species, prep, lighting and the topcoat, so test the full stain-and-topcoat process on scrap first. On blotch-prone woods like pine, GF Water-Based Pre-Stain Conditioner Natural evens out color but limits how much stain soaks in, so a darker color may be needed. GF notes that California users who add more than 2% GF Extender make the stain non-compliant under SCAQMD rules. The Hickory SDS (rev. 02-Feb-2024) uses the signal word Danger: may cause cancer. Wear the protection it lists, and use the respirator GF specifies when spraying. Store between 50 and 80 F and do not pour leftovers down the drain.\u003c\/p\u003e\n\u003ch3\u003eQuestions\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eCan I use it over a finished cabinet?\u003c\/strong\u003e Yes, after cleaning, scuff-sanding and an adhesion test, using thin coats like a gel stain.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCan I put an oil-based polyurethane over it?\u003c\/strong\u003e Yes. GF says to let the stain dry 24 hours first. Oil-based topcoats can amber, so test the look.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDoes it need a topcoat?\u003c\/strong\u003e Yes. GF says the stain provides color but is not durable on its own; finish with 3 coats of a GF topcoat.\u003c\/p\u003e\n\u003ch3\u003eShop related\u003c\/h3\u003e\n\u003cp\u003eOther colors in this size: \u003ca href=\"\/products\/general-finishes-water-based-stain-antique-brown-pint\"\u003eAntique Brown\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-antique-oak-pint\"\u003eAntique Oak\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-black-pint\"\u003eBlack\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-black-cherry-pint\"\u003eBlack Cherry\u003c\/a\u003e. Even out pine with \u003ca href=\"\/products\/general-finishes-pre-stain-conditioner-natural-pint\"\u003eGF Water-Based Pre-Stain Conditioner Natural\u003c\/a\u003e. Topcoat with \u003ca href=\"\/products\/general-finishes-high-performance-water-based-topcoat-clear-satin-quart\"\u003eGF High Performance Topcoat, Satin\u003c\/a\u003e or see all sheens in \u003ca href=\"\/collections\/general-finishes-high-performance\"\u003eHigh Performance Topcoat\u003c\/a\u003e. Prep with a \u003ca href=\"\/products\/3m-softback-contour-sanding-sponge-fine-4-1-2-inch\"\u003e3M Softback sanding sponge\u003c\/a\u003e. Browse every color in \u003ca href=\"\/collections\/general-finishes-water-based-wood-stain\"\u003eGF Water-Based Wood Stain\u003c\/a\u003e, compare \u003ca href=\"\/collections\/curated-wood-stains-gel-stains\"\u003ewood stains and gel stains\u003c\/a\u003e, or plan the job with the \u003ca href=\"\/pages\/furniture-refinishing-project-cart\"\u003efurniture refinishing project cart\u003c\/a\u003e or \u003ca href=\"\/pages\/paint-cabinets-project-cart\"\u003ecabinet project cart\u003c\/a\u003e.\u003c\/p\u003e","brand":"General Finishes","offers":[{"title":"Default Title","offer_id":67673250464054,"sku":"WHPT","price":25.16,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0931\/9750\/0726\/files\/606016103072.jpg?v=1791581988"},{"product_id":"general-finishes-water-based-stain-onyx-quart","title":"General Finishes Water-Based Stain, Onyx, Quart","description":"\u003cp\u003eGeneral Finishes Water-Based Wood Stain in Onyx is a water-based pigmented stain for interior raw wood such as cabinets, trim, doors and furniture. General Finishes says its pigments give rich, dark, uniform color on hard-to-stain woods like maple and pine, and that it can also go over an existing finish, much like an oil-based gel stain. It is low odor, cleans up with water and is noncombustible. This is the quart (32 fl oz) can, GF item WFQT.\u003c\/p\u003e\n\u003ch3\u003eHighlights\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eOne coat is recommended; a second coat after the first is fully dry makes the color darker. GF says not to go past two coats.\u003c\/li\u003e\n\u003cli\u003eDry to the touch in 30 minutes; ready for a second coat or a water-based topcoat in 2 hours (70 F, 50% humidity). Wait 24 hours before an oil-based topcoat.\u003c\/li\u003e\n\u003cli\u003eBrush, foam brush, pad, microfiber roller or spray (HVLP 1.1-1.3 mm).\u003c\/li\u003e\n\u003cli\u003eStain gives color only; finish with 3 coats of a GF topcoat.\u003c\/li\u003e\n\u003cli\u003eThin with distilled water, starting at 5% and up to 10% by volume.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eBest for\u003c\/h3\u003e\n\u003cp\u003eIndoor cabinets, furniture, trim and doors, on raw wood or on a cleaned and scuff-sanded existing finish after an adhesion test. It is an interior stain; for outdoor wood, GF makes a separate Exterior 450 stain.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003eColor \/ size\u003c\/th\u003e\n\u003ctd\u003eOnyx \/ Quart (32 fl oz)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eGF item \/ UPC\u003c\/th\u003e\n\u003ctd\u003eWFQT \/ 606016103355\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eType\u003c\/th\u003e\n\u003ctd\u003eWater-based pigmented stain, interior\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoverage\u003c\/th\u003e\n\u003ctd\u003eUp to 600 sq ft per gallon (TDS), so up to about 150 sq ft for this can (calculated)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDry times\u003c\/th\u003e\n\u003ctd\u003eTouch 30 minutes; recoat 2 hours; 24 hours before an oil-based topcoat (70 F, 50% humidity; cool, humid or thick coats take longer)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoats\u003c\/th\u003e\n\u003ctd\u003e1 recommended, 2 maximum\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply with\u003c\/th\u003e\n\u003ctd\u003eSynthetic-bristle or foam brush, pad applicator, short-nap or foam roller, or spray. HVLP 1.1-1.3 mm; air-assist airless .007 in; airless fine finish .007-.009 in\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply when\u003c\/th\u003e\n\u003ctd\u003eAbout 70 F and 50% humidity, out of direct sun. GF Accelerator helps in cool or humid conditions, GF Extender in warm or dry ones.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThinning\u003c\/th\u003e\n\u003ctd\u003eDistilled water, 5% up to 10% by volume\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eClean up\u003c\/th\u003e\n\u003ctd\u003eSoap and water (hands); GF Brush \u0026amp; Gun Cleaner (equipment)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSolids\u003c\/th\u003e\n\u003ctd\u003e12-22% by volume, 14-20% by weight (varies by color)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVOC\u003c\/th\u003e\n\u003ctd\u003eUnder 150 g\/L on the Onyx SDS (rev. 02-Feb-2024); the TDS says all colors are under 185 g\/L\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAir quality\u003c\/th\u003e\n\u003ctd\u003eSCAQMD, CARB, Canada, OTC Phase I and II compliant (TDS)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStorage\u003c\/th\u003e\n\u003ctd\u003e50-80 F, tightly sealed, out of sun; best used within a year of the date on the can\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSources\u003c\/th\u003e\n\u003ctd\u003e\n\u003ca href=\"https:\/\/generalfinishes.com\/wood-finishes-retail\/water-based-wood-stains-and-dye-stains\/water-based-wood-stain\" target=\"_blank\" rel=\"noopener\"\u003eGeneral Finishes Water-Based Wood Stain page\u003c\/a\u003e; \u003ca href=\"https:\/\/generalfinishes.com\/sites\/default\/files\/documents\/files\/2020-04\/TDS-2020-03-Water-Based-Wood-Stain-General-Finishes.pdf\" target=\"_blank\" rel=\"noopener\"\u003eTechnical data sheet (March 2020)\u003c\/a\u003e; \u003ca href=\"https:\/\/generalfinishes.com\/sites\/default\/files\/documents\/files\/2024-02\/SDS-English-Water-Based-Wood-Stain-ONYX-Water-Base-General-Finishes-US-HCS-2012-v1-2024-02-02.PDF\" target=\"_blank\" rel=\"noopener\"\u003eOnyx SDS (rev. 02-Feb-2024)\u003c\/a\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\u003ch3\u003eHow much do I need?\u003c\/h3\u003e\n\u003cp\u003eGF rates the stain at up to 600 sq ft per gallon, so this quart covers up to about 150 sq ft (calculated). Porous or softer woods take more. If you plan a second coat, count it as another full pass.\u003c\/p\u003e\n\u003ch3\u003eHow to apply\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eRaw wood: sand with 120 grit, then 150 or 220 grit, and remove the dust. GF says no finer than 220 on closed-grain woods or 180 on open-grain woods. To reduce grain raise, wet the wood with water, let it dry and sand smooth before staining.\u003c\/li\u003e\n\u003cli\u003eExisting finish: scuff-clean with a non-woven pad and a 50:50 mix of denatured alcohol and water, dry 1-2 hours, then sand lightly with a 220-320 grit sponge. Remove dust and test adhesion.\u003c\/li\u003e\n\u003cli\u003eWork in a ventilated area and stir before and during use. On raw wood, apply a liberal amount to one section at a time, then wipe off the excess with the grain using absorbent terry cloth or paper towel. Do not use cotton T-shirts; they push the stain around. Correct lap marks right away by rewetting the whole section and wiping again.\u003c\/li\u003e\n\u003cli\u003eOver an existing finish, use thin coats with a foam brush or staining pad and avoid heavy build.\u003c\/li\u003e\n\u003cli\u003eLet it dry at least 2 hours (24 hours under an oil-based topcoat), then apply 3 coats of a GF topcoat. Take care not to sand through the first topcoat coat.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eGood to know\u003c\/h3\u003e\n\u003cp\u003eStain color changes with wood species, prep, lighting and the topcoat, so test the full stain-and-topcoat process on scrap first. On blotch-prone woods like pine, GF Water-Based Pre-Stain Conditioner Natural evens out color but limits how much stain soaks in, so a darker color may be needed. GF notes that California users who add more than 2% GF Extender make the stain non-compliant under SCAQMD rules. The Onyx SDS (rev. 02-Feb-2024) uses the signal word Danger: may cause cancer. Wear the protection it lists, and use the respirator GF specifies when spraying. Store between 50 and 80 F and do not pour leftovers down the drain.\u003c\/p\u003e\n\u003ch3\u003eQuestions\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eCan I use it over a finished cabinet?\u003c\/strong\u003e Yes, after cleaning, scuff-sanding and an adhesion test, using thin coats like a gel stain.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCan I put an oil-based polyurethane over it?\u003c\/strong\u003e Yes. GF says to let the stain dry 24 hours first. Oil-based topcoats can amber, so test the look.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDoes it need a topcoat?\u003c\/strong\u003e Yes. GF says the stain provides color but is not durable on its own; finish with 3 coats of a GF topcoat.\u003c\/p\u003e\n\u003ch3\u003eShop related\u003c\/h3\u003e\n\u003cp\u003eOther colors in this size: \u003ca href=\"\/products\/general-finishes-water-based-stain-antique-brown-quart\"\u003eAntique Brown\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-antique-oak-quart\"\u003eAntique Oak\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-black-quart\"\u003eBlack\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-black-cherry-quart\"\u003eBlack Cherry\u003c\/a\u003e. Even out pine with \u003ca href=\"\/products\/general-finishes-pre-stain-conditioner-natural-quart\"\u003eGF Water-Based Pre-Stain Conditioner Natural\u003c\/a\u003e. Topcoat with \u003ca href=\"\/products\/general-finishes-high-performance-water-based-topcoat-clear-satin-quart\"\u003eGF High Performance Topcoat, Satin\u003c\/a\u003e or see all sheens in \u003ca href=\"\/collections\/general-finishes-high-performance\"\u003eHigh Performance Topcoat\u003c\/a\u003e. Prep with a \u003ca href=\"\/products\/3m-softback-contour-sanding-sponge-fine-4-1-2-inch\"\u003e3M Softback sanding sponge\u003c\/a\u003e. Browse every color in \u003ca href=\"\/collections\/general-finishes-water-based-wood-stain\"\u003eGF Water-Based Wood Stain\u003c\/a\u003e, compare \u003ca href=\"\/collections\/curated-wood-stains-gel-stains\"\u003ewood stains and gel stains\u003c\/a\u003e, or plan the job with the \u003ca href=\"\/pages\/furniture-refinishing-project-cart\"\u003efurniture refinishing project cart\u003c\/a\u003e or \u003ca href=\"\/pages\/paint-cabinets-project-cart\"\u003ecabinet project cart\u003c\/a\u003e.\u003c\/p\u003e","brand":"General Finishes","offers":[{"title":"Default Title","offer_id":67673250496822,"sku":"WFQT","price":39.46,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0931\/9750\/0726\/files\/606016103355.jpg?v=1791581991"},{"product_id":"general-finishes-water-based-stain-provincial-pint","title":"General Finishes Water-Based Stain, Provincial, Pint","description":"\u003cp\u003eGeneral Finishes Water-Based Wood Stain in Provincial is a water-based pigmented stain for interior raw wood such as cabinets, trim, doors and furniture. General Finishes says its pigments give rich, dark, uniform color on hard-to-stain woods like maple and pine, and that it can also go over an existing finish, much like an oil-based gel stain. It is low odor, cleans up with water and is noncombustible. This is the pint (16 fl oz) can, GF item WVPT.\u003c\/p\u003e\n\u003ch3\u003eHighlights\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eOne coat is recommended; a second coat after the first is fully dry makes the color darker. GF says not to go past two coats.\u003c\/li\u003e\n\u003cli\u003eDry to the touch in 30 minutes; ready for a second coat or a water-based topcoat in 2 hours (70 F, 50% humidity). Wait 24 hours before an oil-based topcoat.\u003c\/li\u003e\n\u003cli\u003eBrush, foam brush, pad, microfiber roller or spray (HVLP 1.1-1.3 mm).\u003c\/li\u003e\n\u003cli\u003eStain gives color only; finish with 3 coats of a GF topcoat.\u003c\/li\u003e\n\u003cli\u003eThin with distilled water, starting at 5% and up to 10% by volume.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eBest for\u003c\/h3\u003e\n\u003cp\u003eIndoor cabinets, furniture, trim and doors, on raw wood or on a cleaned and scuff-sanded existing finish after an adhesion test. It is an interior stain; for outdoor wood, GF makes a separate Exterior 450 stain.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003eColor \/ size\u003c\/th\u003e\n\u003ctd\u003eProvincial \/ Pint (16 fl oz)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eGF item \/ UPC\u003c\/th\u003e\n\u003ctd\u003eWVPT \/ 606016103133\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eType\u003c\/th\u003e\n\u003ctd\u003eWater-based pigmented stain, interior\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoverage\u003c\/th\u003e\n\u003ctd\u003eUp to 600 sq ft per gallon (TDS), so up to about 75 sq ft for this can (calculated)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDry times\u003c\/th\u003e\n\u003ctd\u003eTouch 30 minutes; recoat 2 hours; 24 hours before an oil-based topcoat (70 F, 50% humidity; cool, humid or thick coats take longer)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoats\u003c\/th\u003e\n\u003ctd\u003e1 recommended, 2 maximum\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply with\u003c\/th\u003e\n\u003ctd\u003eSynthetic-bristle or foam brush, pad applicator, short-nap or foam roller, or spray. HVLP 1.1-1.3 mm; air-assist airless .007 in; airless fine finish .007-.009 in\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply when\u003c\/th\u003e\n\u003ctd\u003eAbout 70 F and 50% humidity, out of direct sun. GF Accelerator helps in cool or humid conditions, GF Extender in warm or dry ones.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThinning\u003c\/th\u003e\n\u003ctd\u003eDistilled water, 5% up to 10% by volume\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eClean up\u003c\/th\u003e\n\u003ctd\u003eSoap and water (hands); GF Brush \u0026amp; Gun Cleaner (equipment)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSolids\u003c\/th\u003e\n\u003ctd\u003e12-22% by volume, 14-20% by weight (varies by color)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVOC\u003c\/th\u003e\n\u003ctd\u003eUnder 165 g\/L on the Provincial SDS (rev. 02-Feb-2024); the TDS says all colors are under 185 g\/L\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAir quality\u003c\/th\u003e\n\u003ctd\u003eSCAQMD, CARB, Canada, OTC Phase I and II compliant (TDS)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStorage\u003c\/th\u003e\n\u003ctd\u003e50-80 F, tightly sealed, out of sun; best used within a year of the date on the can\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSources\u003c\/th\u003e\n\u003ctd\u003e\n\u003ca href=\"https:\/\/generalfinishes.com\/wood-finishes-retail\/water-based-wood-stains-and-dye-stains\/water-based-wood-stain\" target=\"_blank\" rel=\"noopener\"\u003eGeneral Finishes Water-Based Wood Stain page\u003c\/a\u003e; \u003ca href=\"https:\/\/generalfinishes.com\/sites\/default\/files\/documents\/files\/2020-04\/TDS-2020-03-Water-Based-Wood-Stain-General-Finishes.pdf\" target=\"_blank\" rel=\"noopener\"\u003eTechnical data sheet (March 2020)\u003c\/a\u003e; \u003ca href=\"https:\/\/generalfinishes.com\/sites\/default\/files\/documents\/files\/2024-02\/SDS-English-Water-Based-Wood-Stain-PROVINCIAL-Water-Base-General-Finishes-US-HCS-2012-v1-2024-02-02.PDF\" target=\"_blank\" rel=\"noopener\"\u003eProvincial SDS (rev. 02-Feb-2024)\u003c\/a\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\u003ch3\u003eHow much do I need?\u003c\/h3\u003e\n\u003cp\u003eGF rates the stain at up to 600 sq ft per gallon, so this pint covers up to about 75 sq ft (calculated). Porous or softer woods take more. If you plan a second coat, count it as another full pass.\u003c\/p\u003e\n\u003ch3\u003eHow to apply\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eRaw wood: sand with 120 grit, then 150 or 220 grit, and remove the dust. GF says no finer than 220 on closed-grain woods or 180 on open-grain woods. To reduce grain raise, wet the wood with water, let it dry and sand smooth before staining.\u003c\/li\u003e\n\u003cli\u003eExisting finish: scuff-clean with a non-woven pad and a 50:50 mix of denatured alcohol and water, dry 1-2 hours, then sand lightly with a 220-320 grit sponge. Remove dust and test adhesion.\u003c\/li\u003e\n\u003cli\u003eWork in a ventilated area and stir before and during use. On raw wood, apply a liberal amount to one section at a time, then wipe off the excess with the grain using absorbent terry cloth or paper towel. Do not use cotton T-shirts; they push the stain around. Correct lap marks right away by rewetting the whole section and wiping again.\u003c\/li\u003e\n\u003cli\u003eOver an existing finish, use thin coats with a foam brush or staining pad and avoid heavy build.\u003c\/li\u003e\n\u003cli\u003eLet it dry at least 2 hours (24 hours under an oil-based topcoat), then apply 3 coats of a GF topcoat. Take care not to sand through the first topcoat coat.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eGood to know\u003c\/h3\u003e\n\u003cp\u003eStain color changes with wood species, prep, lighting and the topcoat, so test the full stain-and-topcoat process on scrap first. On blotch-prone woods like pine, GF Water-Based Pre-Stain Conditioner Natural evens out color but limits how much stain soaks in, so a darker color may be needed. GF notes that California users who add more than 2% GF Extender make the stain non-compliant under SCAQMD rules. The Provincial SDS (rev. 02-Feb-2024) uses the signal word Danger: may cause cancer. Wear the protection it lists, and use the respirator GF specifies when spraying. Store between 50 and 80 F and do not pour leftovers down the drain.\u003c\/p\u003e\n\u003ch3\u003eQuestions\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eCan I use it over a finished cabinet?\u003c\/strong\u003e Yes, after cleaning, scuff-sanding and an adhesion test, using thin coats like a gel stain.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCan I put an oil-based polyurethane over it?\u003c\/strong\u003e Yes. GF says to let the stain dry 24 hours first. Oil-based topcoats can amber, so test the look.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDoes it need a topcoat?\u003c\/strong\u003e Yes. GF says the stain provides color but is not durable on its own; finish with 3 coats of a GF topcoat.\u003c\/p\u003e\n\u003ch3\u003eShop related\u003c\/h3\u003e\n\u003cp\u003eSame color, other size: \u003ca href=\"\/products\/general-finishes-water-based-stain-provincial-quart\"\u003eProvincial Quart\u003c\/a\u003e. Other colors in this size: \u003ca href=\"\/products\/general-finishes-water-based-stain-antique-brown-pint\"\u003eAntique Brown\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-antique-oak-pint\"\u003eAntique Oak\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-black-pint\"\u003eBlack\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-black-cherry-pint\"\u003eBlack Cherry\u003c\/a\u003e. Even out pine with \u003ca href=\"\/products\/general-finishes-pre-stain-conditioner-natural-pint\"\u003eGF Water-Based Pre-Stain Conditioner Natural\u003c\/a\u003e. Topcoat with \u003ca href=\"\/products\/general-finishes-high-performance-water-based-topcoat-clear-satin-quart\"\u003eGF High Performance Topcoat, Satin\u003c\/a\u003e or see all sheens in \u003ca href=\"\/collections\/general-finishes-high-performance\"\u003eHigh Performance Topcoat\u003c\/a\u003e. Prep with a \u003ca href=\"\/products\/3m-softback-contour-sanding-sponge-fine-4-1-2-inch\"\u003e3M Softback sanding sponge\u003c\/a\u003e. Browse every color in \u003ca href=\"\/collections\/general-finishes-water-based-wood-stain\"\u003eGF Water-Based Wood Stain\u003c\/a\u003e, compare \u003ca href=\"\/collections\/curated-wood-stains-gel-stains\"\u003ewood stains and gel stains\u003c\/a\u003e, or plan the job with the \u003ca href=\"\/pages\/furniture-refinishing-project-cart\"\u003efurniture refinishing project cart\u003c\/a\u003e or \u003ca href=\"\/pages\/paint-cabinets-project-cart\"\u003ecabinet project cart\u003c\/a\u003e.\u003c\/p\u003e","brand":"General Finishes","offers":[{"title":"Default Title","offer_id":67673250529590,"sku":"WVPT","price":25.16,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0931\/9750\/0726\/files\/606016103133.jpg?v=1791581993"},{"product_id":"general-finishes-water-based-stain-provincial-quart","title":"General Finishes Water-Based Stain, Provincial, Quart","description":"\u003cp\u003eGeneral Finishes Water-Based Wood Stain in Provincial is a water-based pigmented stain for interior raw wood such as cabinets, trim, doors and furniture. General Finishes says its pigments give rich, dark, uniform color on hard-to-stain woods like maple and pine, and that it can also go over an existing finish, much like an oil-based gel stain. It is low odor, cleans up with water and is noncombustible. This is the quart (32 fl oz) can, GF item WVQT.\u003c\/p\u003e\n\u003ch3\u003eHighlights\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eOne coat is recommended; a second coat after the first is fully dry makes the color darker. GF says not to go past two coats.\u003c\/li\u003e\n\u003cli\u003eDry to the touch in 30 minutes; ready for a second coat or a water-based topcoat in 2 hours (70 F, 50% humidity). Wait 24 hours before an oil-based topcoat.\u003c\/li\u003e\n\u003cli\u003eBrush, foam brush, pad, microfiber roller or spray (HVLP 1.1-1.3 mm).\u003c\/li\u003e\n\u003cli\u003eStain gives color only; finish with 3 coats of a GF topcoat.\u003c\/li\u003e\n\u003cli\u003eThin with distilled water, starting at 5% and up to 10% by volume.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eBest for\u003c\/h3\u003e\n\u003cp\u003eIndoor cabinets, furniture, trim and doors, on raw wood or on a cleaned and scuff-sanded existing finish after an adhesion test. It is an interior stain; for outdoor wood, GF makes a separate Exterior 450 stain.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003eColor \/ size\u003c\/th\u003e\n\u003ctd\u003eProvincial \/ Quart (32 fl oz)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eGF item \/ UPC\u003c\/th\u003e\n\u003ctd\u003eWVQT \/ 606016103317\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eType\u003c\/th\u003e\n\u003ctd\u003eWater-based pigmented stain, interior\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoverage\u003c\/th\u003e\n\u003ctd\u003eUp to 600 sq ft per gallon (TDS), so up to about 150 sq ft for this can (calculated)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDry times\u003c\/th\u003e\n\u003ctd\u003eTouch 30 minutes; recoat 2 hours; 24 hours before an oil-based topcoat (70 F, 50% humidity; cool, humid or thick coats take longer)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoats\u003c\/th\u003e\n\u003ctd\u003e1 recommended, 2 maximum\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply with\u003c\/th\u003e\n\u003ctd\u003eSynthetic-bristle or foam brush, pad applicator, short-nap or foam roller, or spray. HVLP 1.1-1.3 mm; air-assist airless .007 in; airless fine finish .007-.009 in\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply when\u003c\/th\u003e\n\u003ctd\u003eAbout 70 F and 50% humidity, out of direct sun. GF Accelerator helps in cool or humid conditions, GF Extender in warm or dry ones.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThinning\u003c\/th\u003e\n\u003ctd\u003eDistilled water, 5% up to 10% by volume\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eClean up\u003c\/th\u003e\n\u003ctd\u003eSoap and water (hands); GF Brush \u0026amp; Gun Cleaner (equipment)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSolids\u003c\/th\u003e\n\u003ctd\u003e12-22% by volume, 14-20% by weight (varies by color)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVOC\u003c\/th\u003e\n\u003ctd\u003eUnder 165 g\/L on the Provincial SDS (rev. 02-Feb-2024); the TDS says all colors are under 185 g\/L\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAir quality\u003c\/th\u003e\n\u003ctd\u003eSCAQMD, CARB, Canada, OTC Phase I and II compliant (TDS)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStorage\u003c\/th\u003e\n\u003ctd\u003e50-80 F, tightly sealed, out of sun; best used within a year of the date on the can\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSources\u003c\/th\u003e\n\u003ctd\u003e\n\u003ca href=\"https:\/\/generalfinishes.com\/wood-finishes-retail\/water-based-wood-stains-and-dye-stains\/water-based-wood-stain\" target=\"_blank\" rel=\"noopener\"\u003eGeneral Finishes Water-Based Wood Stain page\u003c\/a\u003e; \u003ca href=\"https:\/\/generalfinishes.com\/sites\/default\/files\/documents\/files\/2020-04\/TDS-2020-03-Water-Based-Wood-Stain-General-Finishes.pdf\" target=\"_blank\" rel=\"noopener\"\u003eTechnical data sheet (March 2020)\u003c\/a\u003e; \u003ca href=\"https:\/\/generalfinishes.com\/sites\/default\/files\/documents\/files\/2024-02\/SDS-English-Water-Based-Wood-Stain-PROVINCIAL-Water-Base-General-Finishes-US-HCS-2012-v1-2024-02-02.PDF\" target=\"_blank\" rel=\"noopener\"\u003eProvincial SDS (rev. 02-Feb-2024)\u003c\/a\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\u003ch3\u003eHow much do I need?\u003c\/h3\u003e\n\u003cp\u003eGF rates the stain at up to 600 sq ft per gallon, so this quart covers up to about 150 sq ft (calculated). Porous or softer woods take more. If you plan a second coat, count it as another full pass.\u003c\/p\u003e\n\u003ch3\u003eHow to apply\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eRaw wood: sand with 120 grit, then 150 or 220 grit, and remove the dust. GF says no finer than 220 on closed-grain woods or 180 on open-grain woods. To reduce grain raise, wet the wood with water, let it dry and sand smooth before staining.\u003c\/li\u003e\n\u003cli\u003eExisting finish: scuff-clean with a non-woven pad and a 50:50 mix of denatured alcohol and water, dry 1-2 hours, then sand lightly with a 220-320 grit sponge. Remove dust and test adhesion.\u003c\/li\u003e\n\u003cli\u003eWork in a ventilated area and stir before and during use. On raw wood, apply a liberal amount to one section at a time, then wipe off the excess with the grain using absorbent terry cloth or paper towel. Do not use cotton T-shirts; they push the stain around. Correct lap marks right away by rewetting the whole section and wiping again.\u003c\/li\u003e\n\u003cli\u003eOver an existing finish, use thin coats with a foam brush or staining pad and avoid heavy build.\u003c\/li\u003e\n\u003cli\u003eLet it dry at least 2 hours (24 hours under an oil-based topcoat), then apply 3 coats of a GF topcoat. Take care not to sand through the first topcoat coat.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eGood to know\u003c\/h3\u003e\n\u003cp\u003eStain color changes with wood species, prep, lighting and the topcoat, so test the full stain-and-topcoat process on scrap first. On blotch-prone woods like pine, GF Water-Based Pre-Stain Conditioner Natural evens out color but limits how much stain soaks in, so a darker color may be needed. GF notes that California users who add more than 2% GF Extender make the stain non-compliant under SCAQMD rules. The Provincial SDS (rev. 02-Feb-2024) uses the signal word Danger: may cause cancer. Wear the protection it lists, and use the respirator GF specifies when spraying. Store between 50 and 80 F and do not pour leftovers down the drain.\u003c\/p\u003e\n\u003ch3\u003eQuestions\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eCan I use it over a finished cabinet?\u003c\/strong\u003e Yes, after cleaning, scuff-sanding and an adhesion test, using thin coats like a gel stain.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCan I put an oil-based polyurethane over it?\u003c\/strong\u003e Yes. GF says to let the stain dry 24 hours first. Oil-based topcoats can amber, so test the look.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDoes it need a topcoat?\u003c\/strong\u003e Yes. GF says the stain provides color but is not durable on its own; finish with 3 coats of a GF topcoat.\u003c\/p\u003e\n\u003ch3\u003eShop related\u003c\/h3\u003e\n\u003cp\u003eSame color, other size: \u003ca href=\"\/products\/general-finishes-water-based-stain-provincial-pint\"\u003eProvincial Pint\u003c\/a\u003e. Other colors in this size: \u003ca href=\"\/products\/general-finishes-water-based-stain-antique-brown-quart\"\u003eAntique Brown\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-antique-oak-quart\"\u003eAntique Oak\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-black-quart\"\u003eBlack\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-black-cherry-quart\"\u003eBlack Cherry\u003c\/a\u003e. Even out pine with \u003ca href=\"\/products\/general-finishes-pre-stain-conditioner-natural-quart\"\u003eGF Water-Based Pre-Stain Conditioner Natural\u003c\/a\u003e. Topcoat with \u003ca href=\"\/products\/general-finishes-high-performance-water-based-topcoat-clear-satin-quart\"\u003eGF High Performance Topcoat, Satin\u003c\/a\u003e or see all sheens in \u003ca href=\"\/collections\/general-finishes-high-performance\"\u003eHigh Performance Topcoat\u003c\/a\u003e. Prep with a \u003ca href=\"\/products\/3m-softback-contour-sanding-sponge-fine-4-1-2-inch\"\u003e3M Softback sanding sponge\u003c\/a\u003e. Browse every color in \u003ca href=\"\/collections\/general-finishes-water-based-wood-stain\"\u003eGF Water-Based Wood Stain\u003c\/a\u003e, compare \u003ca href=\"\/collections\/curated-wood-stains-gel-stains\"\u003ewood stains and gel stains\u003c\/a\u003e, or plan the job with the \u003ca href=\"\/pages\/furniture-refinishing-project-cart\"\u003efurniture refinishing project cart\u003c\/a\u003e or \u003ca href=\"\/pages\/paint-cabinets-project-cart\"\u003ecabinet project cart\u003c\/a\u003e.\u003c\/p\u003e","brand":"General Finishes","offers":[{"title":"Default Title","offer_id":67673250562358,"sku":"WVQT","price":39.46,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0931\/9750\/0726\/files\/606016103317.jpg?v=1791581995"},{"product_id":"general-finishes-water-based-stain-antique-oak-pint","title":"General Finishes Water-Based Stain, Antique Oak, Pint","description":"\u003cp\u003eGeneral Finishes Water-Based Wood Stain in Antique Oak is a water-based pigmented stain for interior raw wood such as cabinets, trim, doors and furniture. General Finishes says its pigments give rich, dark, uniform color on hard-to-stain woods like maple and pine, and that it can also go over an existing finish, much like an oil-based gel stain. It is low odor, cleans up with water and is noncombustible. This is the pint (16 fl oz) can, GF item WOPT.\u003c\/p\u003e\n\u003ch3\u003eHighlights\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eOne coat is recommended; a second coat after the first is fully dry makes the color darker. GF says not to go past two coats.\u003c\/li\u003e\n\u003cli\u003eDry to the touch in 30 minutes; ready for a second coat or a water-based topcoat in 2 hours (70 F, 50% humidity). Wait 24 hours before an oil-based topcoat.\u003c\/li\u003e\n\u003cli\u003eBrush, foam brush, pad, microfiber roller or spray (HVLP 1.1-1.3 mm).\u003c\/li\u003e\n\u003cli\u003eStain gives color only; finish with 3 coats of a GF topcoat.\u003c\/li\u003e\n\u003cli\u003eThin with distilled water, starting at 5% and up to 10% by volume.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eBest for\u003c\/h3\u003e\n\u003cp\u003eIndoor cabinets, furniture, trim and doors, on raw wood or on a cleaned and scuff-sanded existing finish after an adhesion test. It is an interior stain; for outdoor wood, GF makes a separate Exterior 450 stain.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003eColor \/ size\u003c\/th\u003e\n\u003ctd\u003eAntique Oak \/ Pint (16 fl oz)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eGF item \/ UPC\u003c\/th\u003e\n\u003ctd\u003eWOPT \/ 606016100033\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eType\u003c\/th\u003e\n\u003ctd\u003eWater-based pigmented stain, interior\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoverage\u003c\/th\u003e\n\u003ctd\u003eUp to 600 sq ft per gallon (TDS), so up to about 75 sq ft for this can (calculated)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDry times\u003c\/th\u003e\n\u003ctd\u003eTouch 30 minutes; recoat 2 hours; 24 hours before an oil-based topcoat (70 F, 50% humidity; cool, humid or thick coats take longer)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoats\u003c\/th\u003e\n\u003ctd\u003e1 recommended, 2 maximum\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply with\u003c\/th\u003e\n\u003ctd\u003eSynthetic-bristle or foam brush, pad applicator, short-nap or foam roller, or spray. HVLP 1.1-1.3 mm; air-assist airless .007 in; airless fine finish .007-.009 in\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply when\u003c\/th\u003e\n\u003ctd\u003eAbout 70 F and 50% humidity, out of direct sun. GF Accelerator helps in cool or humid conditions, GF Extender in warm or dry ones.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThinning\u003c\/th\u003e\n\u003ctd\u003eDistilled water, 5% up to 10% by volume\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eClean up\u003c\/th\u003e\n\u003ctd\u003eSoap and water (hands); GF Brush \u0026amp; Gun Cleaner (equipment)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSolids\u003c\/th\u003e\n\u003ctd\u003e12-22% by volume, 14-20% by weight (varies by color)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVOC\u003c\/th\u003e\n\u003ctd\u003eUnder 185 g\/L on the Antique Oak SDS (rev. 02-Feb-2024); the TDS says all colors are under 185 g\/L\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAir quality\u003c\/th\u003e\n\u003ctd\u003eSCAQMD, CARB, Canada, OTC Phase I and II compliant (TDS)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStorage\u003c\/th\u003e\n\u003ctd\u003e50-80 F, tightly sealed, out of sun; best used within a year of the date on the can\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSources\u003c\/th\u003e\n\u003ctd\u003e\n\u003ca href=\"https:\/\/generalfinishes.com\/wood-finishes-retail\/water-based-wood-stains-and-dye-stains\/water-based-wood-stain\" target=\"_blank\" rel=\"noopener\"\u003eGeneral Finishes Water-Based Wood Stain page\u003c\/a\u003e; \u003ca href=\"https:\/\/generalfinishes.com\/sites\/default\/files\/documents\/files\/2020-04\/TDS-2020-03-Water-Based-Wood-Stain-General-Finishes.pdf\" target=\"_blank\" rel=\"noopener\"\u003eTechnical data sheet (March 2020)\u003c\/a\u003e; \u003ca href=\"https:\/\/generalfinishes.com\/sites\/default\/files\/documents\/files\/2024-02\/SDS-English-Water-Based-Wood-Stain-ANTIQUE-OAK-Water-Base-General-Finishes-US-HCS-2012-v1-2024-02-02.PDF\" target=\"_blank\" rel=\"noopener\"\u003eAntique Oak SDS (rev. 02-Feb-2024)\u003c\/a\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\u003ch3\u003eHow much do I need?\u003c\/h3\u003e\n\u003cp\u003eGF rates the stain at up to 600 sq ft per gallon, so this pint covers up to about 75 sq ft (calculated). Porous or softer woods take more. If you plan a second coat, count it as another full pass.\u003c\/p\u003e\n\u003ch3\u003eHow to apply\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eRaw wood: sand with 120 grit, then 150 or 220 grit, and remove the dust. GF says no finer than 220 on closed-grain woods or 180 on open-grain woods. To reduce grain raise, wet the wood with water, let it dry and sand smooth before staining.\u003c\/li\u003e\n\u003cli\u003eExisting finish: scuff-clean with a non-woven pad and a 50:50 mix of denatured alcohol and water, dry 1-2 hours, then sand lightly with a 220-320 grit sponge. Remove dust and test adhesion.\u003c\/li\u003e\n\u003cli\u003eWork in a ventilated area and stir before and during use. On raw wood, apply a liberal amount to one section at a time, then wipe off the excess with the grain using absorbent terry cloth or paper towel. Do not use cotton T-shirts; they push the stain around. Correct lap marks right away by rewetting the whole section and wiping again.\u003c\/li\u003e\n\u003cli\u003eOver an existing finish, use thin coats with a foam brush or staining pad and avoid heavy build.\u003c\/li\u003e\n\u003cli\u003eLet it dry at least 2 hours (24 hours under an oil-based topcoat), then apply 3 coats of a GF topcoat. Take care not to sand through the first topcoat coat.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eGood to know\u003c\/h3\u003e\n\u003cp\u003eStain color changes with wood species, prep, lighting and the topcoat, so test the full stain-and-topcoat process on scrap first. On blotch-prone woods like pine, GF Water-Based Pre-Stain Conditioner Natural evens out color but limits how much stain soaks in, so a darker color may be needed. GF notes that California users who add more than 2% GF Extender make the stain non-compliant under SCAQMD rules. The Antique Oak SDS (rev. 02-Feb-2024) uses the signal word Danger: may cause cancer. Wear the protection it lists, and use the respirator GF specifies when spraying. Store between 50 and 80 F and do not pour leftovers down the drain.\u003c\/p\u003e\n\u003ch3\u003eQuestions\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eCan I use it over a finished cabinet?\u003c\/strong\u003e Yes, after cleaning, scuff-sanding and an adhesion test, using thin coats like a gel stain.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCan I put an oil-based polyurethane over it?\u003c\/strong\u003e Yes. GF says to let the stain dry 24 hours first. Oil-based topcoats can amber, so test the look.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDoes it need a topcoat?\u003c\/strong\u003e Yes. GF says the stain provides color but is not durable on its own; finish with 3 coats of a GF topcoat.\u003c\/p\u003e\n\u003ch3\u003eShop related\u003c\/h3\u003e\n\u003cp\u003eSame color, other size: \u003ca href=\"\/products\/general-finishes-water-based-stain-antique-oak-quart\"\u003eAntique Oak Quart\u003c\/a\u003e. Other colors in this size: \u003ca href=\"\/products\/general-finishes-water-based-stain-antique-brown-pint\"\u003eAntique Brown\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-black-pint\"\u003eBlack\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-black-cherry-pint\"\u003eBlack Cherry\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-brown-mahogany-pint\"\u003eBrown Mahogany\u003c\/a\u003e. Even out pine with \u003ca href=\"\/products\/general-finishes-pre-stain-conditioner-natural-pint\"\u003eGF Water-Based Pre-Stain Conditioner Natural\u003c\/a\u003e. Topcoat with \u003ca href=\"\/products\/general-finishes-high-performance-water-based-topcoat-clear-satin-quart\"\u003eGF High Performance Topcoat, Satin\u003c\/a\u003e or see all sheens in \u003ca href=\"\/collections\/general-finishes-high-performance\"\u003eHigh Performance Topcoat\u003c\/a\u003e. Prep with a \u003ca href=\"\/products\/3m-softback-contour-sanding-sponge-fine-4-1-2-inch\"\u003e3M Softback sanding sponge\u003c\/a\u003e. Browse every color in \u003ca href=\"\/collections\/general-finishes-water-based-wood-stain\"\u003eGF Water-Based Wood Stain\u003c\/a\u003e, compare \u003ca href=\"\/collections\/curated-wood-stains-gel-stains\"\u003ewood stains and gel stains\u003c\/a\u003e, or plan the job with the \u003ca href=\"\/pages\/furniture-refinishing-project-cart\"\u003efurniture refinishing project cart\u003c\/a\u003e or \u003ca href=\"\/pages\/paint-cabinets-project-cart\"\u003ecabinet project cart\u003c\/a\u003e.\u003c\/p\u003e","brand":"General Finishes","offers":[{"title":"Default Title","offer_id":67673250595126,"sku":"WOPT","price":25.16,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0931\/9750\/0726\/files\/606016100033.jpg?v=1791581997"},{"product_id":"general-finishes-water-based-stain-antique-oak-quart","title":"General Finishes Water-Based Stain, Antique Oak, Quart","description":"\u003cp\u003eGeneral Finishes Water-Based Wood Stain in Antique Oak is a water-based pigmented stain for interior raw wood such as cabinets, trim, doors and furniture. General Finishes says its pigments give rich, dark, uniform color on hard-to-stain woods like maple and pine, and that it can also go over an existing finish, much like an oil-based gel stain. It is low odor, cleans up with water and is noncombustible. This is the quart (32 fl oz) can, GF item WOQT.\u003c\/p\u003e\n\u003ch3\u003eHighlights\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eOne coat is recommended; a second coat after the first is fully dry makes the color darker. GF says not to go past two coats.\u003c\/li\u003e\n\u003cli\u003eDry to the touch in 30 minutes; ready for a second coat or a water-based topcoat in 2 hours (70 F, 50% humidity). Wait 24 hours before an oil-based topcoat.\u003c\/li\u003e\n\u003cli\u003eBrush, foam brush, pad, microfiber roller or spray (HVLP 1.1-1.3 mm).\u003c\/li\u003e\n\u003cli\u003eStain gives color only; finish with 3 coats of a GF topcoat.\u003c\/li\u003e\n\u003cli\u003eThin with distilled water, starting at 5% and up to 10% by volume.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eBest for\u003c\/h3\u003e\n\u003cp\u003eIndoor cabinets, furniture, trim and doors, on raw wood or on a cleaned and scuff-sanded existing finish after an adhesion test. It is an interior stain; for outdoor wood, GF makes a separate Exterior 450 stain.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003eColor \/ size\u003c\/th\u003e\n\u003ctd\u003eAntique Oak \/ Quart (32 fl oz)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eGF item \/ UPC\u003c\/th\u003e\n\u003ctd\u003eWOQT \/ 606016100200\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eType\u003c\/th\u003e\n\u003ctd\u003eWater-based pigmented stain, interior\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoverage\u003c\/th\u003e\n\u003ctd\u003eUp to 600 sq ft per gallon (TDS), so up to about 150 sq ft for this can (calculated)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDry times\u003c\/th\u003e\n\u003ctd\u003eTouch 30 minutes; recoat 2 hours; 24 hours before an oil-based topcoat (70 F, 50% humidity; cool, humid or thick coats take longer)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoats\u003c\/th\u003e\n\u003ctd\u003e1 recommended, 2 maximum\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply with\u003c\/th\u003e\n\u003ctd\u003eSynthetic-bristle or foam brush, pad applicator, short-nap or foam roller, or spray. HVLP 1.1-1.3 mm; air-assist airless .007 in; airless fine finish .007-.009 in\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply when\u003c\/th\u003e\n\u003ctd\u003eAbout 70 F and 50% humidity, out of direct sun. GF Accelerator helps in cool or humid conditions, GF Extender in warm or dry ones.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThinning\u003c\/th\u003e\n\u003ctd\u003eDistilled water, 5% up to 10% by volume\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eClean up\u003c\/th\u003e\n\u003ctd\u003eSoap and water (hands); GF Brush \u0026amp; Gun Cleaner (equipment)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSolids\u003c\/th\u003e\n\u003ctd\u003e12-22% by volume, 14-20% by weight (varies by color)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVOC\u003c\/th\u003e\n\u003ctd\u003eUnder 185 g\/L on the Antique Oak SDS (rev. 02-Feb-2024); the TDS says all colors are under 185 g\/L\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAir quality\u003c\/th\u003e\n\u003ctd\u003eSCAQMD, CARB, Canada, OTC Phase I and II compliant (TDS)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStorage\u003c\/th\u003e\n\u003ctd\u003e50-80 F, tightly sealed, out of sun; best used within a year of the date on the can\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSources\u003c\/th\u003e\n\u003ctd\u003e\n\u003ca href=\"https:\/\/generalfinishes.com\/wood-finishes-retail\/water-based-wood-stains-and-dye-stains\/water-based-wood-stain\" target=\"_blank\" rel=\"noopener\"\u003eGeneral Finishes Water-Based Wood Stain page\u003c\/a\u003e; \u003ca href=\"https:\/\/generalfinishes.com\/sites\/default\/files\/documents\/files\/2020-04\/TDS-2020-03-Water-Based-Wood-Stain-General-Finishes.pdf\" target=\"_blank\" rel=\"noopener\"\u003eTechnical data sheet (March 2020)\u003c\/a\u003e; \u003ca href=\"https:\/\/generalfinishes.com\/sites\/default\/files\/documents\/files\/2024-02\/SDS-English-Water-Based-Wood-Stain-ANTIQUE-OAK-Water-Base-General-Finishes-US-HCS-2012-v1-2024-02-02.PDF\" target=\"_blank\" rel=\"noopener\"\u003eAntique Oak SDS (rev. 02-Feb-2024)\u003c\/a\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\u003ch3\u003eHow much do I need?\u003c\/h3\u003e\n\u003cp\u003eGF rates the stain at up to 600 sq ft per gallon, so this quart covers up to about 150 sq ft (calculated). Porous or softer woods take more. If you plan a second coat, count it as another full pass.\u003c\/p\u003e\n\u003ch3\u003eHow to apply\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eRaw wood: sand with 120 grit, then 150 or 220 grit, and remove the dust. GF says no finer than 220 on closed-grain woods or 180 on open-grain woods. To reduce grain raise, wet the wood with water, let it dry and sand smooth before staining.\u003c\/li\u003e\n\u003cli\u003eExisting finish: scuff-clean with a non-woven pad and a 50:50 mix of denatured alcohol and water, dry 1-2 hours, then sand lightly with a 220-320 grit sponge. Remove dust and test adhesion.\u003c\/li\u003e\n\u003cli\u003eWork in a ventilated area and stir before and during use. On raw wood, apply a liberal amount to one section at a time, then wipe off the excess with the grain using absorbent terry cloth or paper towel. Do not use cotton T-shirts; they push the stain around. Correct lap marks right away by rewetting the whole section and wiping again.\u003c\/li\u003e\n\u003cli\u003eOver an existing finish, use thin coats with a foam brush or staining pad and avoid heavy build.\u003c\/li\u003e\n\u003cli\u003eLet it dry at least 2 hours (24 hours under an oil-based topcoat), then apply 3 coats of a GF topcoat. Take care not to sand through the first topcoat coat.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eGood to know\u003c\/h3\u003e\n\u003cp\u003eStain color changes with wood species, prep, lighting and the topcoat, so test the full stain-and-topcoat process on scrap first. On blotch-prone woods like pine, GF Water-Based Pre-Stain Conditioner Natural evens out color but limits how much stain soaks in, so a darker color may be needed. GF notes that California users who add more than 2% GF Extender make the stain non-compliant under SCAQMD rules. The Antique Oak SDS (rev. 02-Feb-2024) uses the signal word Danger: may cause cancer. Wear the protection it lists, and use the respirator GF specifies when spraying. Store between 50 and 80 F and do not pour leftovers down the drain.\u003c\/p\u003e\n\u003ch3\u003eQuestions\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eCan I use it over a finished cabinet?\u003c\/strong\u003e Yes, after cleaning, scuff-sanding and an adhesion test, using thin coats like a gel stain.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCan I put an oil-based polyurethane over it?\u003c\/strong\u003e Yes. GF says to let the stain dry 24 hours first. Oil-based topcoats can amber, so test the look.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDoes it need a topcoat?\u003c\/strong\u003e Yes. GF says the stain provides color but is not durable on its own; finish with 3 coats of a GF topcoat.\u003c\/p\u003e\n\u003ch3\u003eShop related\u003c\/h3\u003e\n\u003cp\u003eSame color, other size: \u003ca href=\"\/products\/general-finishes-water-based-stain-antique-oak-pint\"\u003eAntique Oak Pint\u003c\/a\u003e. Other colors in this size: \u003ca href=\"\/products\/general-finishes-water-based-stain-antique-brown-quart\"\u003eAntique Brown\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-black-quart\"\u003eBlack\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-black-cherry-quart\"\u003eBlack Cherry\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-brown-mahogany-quart\"\u003eBrown Mahogany\u003c\/a\u003e. Even out pine with \u003ca href=\"\/products\/general-finishes-pre-stain-conditioner-natural-quart\"\u003eGF Water-Based Pre-Stain Conditioner Natural\u003c\/a\u003e. Topcoat with \u003ca href=\"\/products\/general-finishes-high-performance-water-based-topcoat-clear-satin-quart\"\u003eGF High Performance Topcoat, Satin\u003c\/a\u003e or see all sheens in \u003ca href=\"\/collections\/general-finishes-high-performance\"\u003eHigh Performance Topcoat\u003c\/a\u003e. Prep with a \u003ca href=\"\/products\/3m-softback-contour-sanding-sponge-fine-4-1-2-inch\"\u003e3M Softback sanding sponge\u003c\/a\u003e. Browse every color in \u003ca href=\"\/collections\/general-finishes-water-based-wood-stain\"\u003eGF Water-Based Wood Stain\u003c\/a\u003e, compare \u003ca href=\"\/collections\/curated-wood-stains-gel-stains\"\u003ewood stains and gel stains\u003c\/a\u003e, or plan the job with the \u003ca href=\"\/pages\/furniture-refinishing-project-cart\"\u003efurniture refinishing project cart\u003c\/a\u003e or \u003ca href=\"\/pages\/paint-cabinets-project-cart\"\u003ecabinet project cart\u003c\/a\u003e.\u003c\/p\u003e","brand":"General Finishes","offers":[{"title":"Default Title","offer_id":67673250627894,"sku":"WOQT","price":39.46,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0931\/9750\/0726\/files\/606016100200.jpg?v=1791581999"},{"product_id":"general-finishes-water-based-stain-black-pint","title":"General Finishes Water-Based Stain, Black, Pint","description":"\u003cp\u003eGeneral Finishes Water-Based Wood Stain in Black is a water-based pigmented stain for interior raw wood such as cabinets, trim, doors and furniture. General Finishes says its pigments give rich, dark, uniform color on hard-to-stain woods like maple and pine, and that it can also go over an existing finish, much like an oil-based gel stain. It is low odor, cleans up with water and is noncombustible. This is the pint (16 fl oz) can, GF item WBPT.\u003c\/p\u003e\n\u003ch3\u003eHighlights\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eOne coat is recommended; a second coat after the first is fully dry makes the color darker. GF says not to go past two coats.\u003c\/li\u003e\n\u003cli\u003eDry to the touch in 30 minutes; ready for a second coat or a water-based topcoat in 2 hours (70 F, 50% humidity). Wait 24 hours before an oil-based topcoat.\u003c\/li\u003e\n\u003cli\u003eBrush, foam brush, pad, microfiber roller or spray (HVLP 1.1-1.3 mm).\u003c\/li\u003e\n\u003cli\u003eStain gives color only; finish with 3 coats of a GF topcoat.\u003c\/li\u003e\n\u003cli\u003eThin with distilled water, starting at 5% and up to 10% by volume.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eBest for\u003c\/h3\u003e\n\u003cp\u003eIndoor cabinets, furniture, trim and doors, on raw wood or on a cleaned and scuff-sanded existing finish after an adhesion test. It is an interior stain; for outdoor wood, GF makes a separate Exterior 450 stain.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003eColor \/ size\u003c\/th\u003e\n\u003ctd\u003eBlack \/ Pint (16 fl oz)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eGF item \/ UPC\u003c\/th\u003e\n\u003ctd\u003eWBPT \/ 606016100576\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eType\u003c\/th\u003e\n\u003ctd\u003eWater-based pigmented stain, interior\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoverage\u003c\/th\u003e\n\u003ctd\u003eUp to 600 sq ft per gallon (TDS), so up to about 75 sq ft for this can (calculated)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDry times\u003c\/th\u003e\n\u003ctd\u003eTouch 30 minutes; recoat 2 hours; 24 hours before an oil-based topcoat (70 F, 50% humidity; cool, humid or thick coats take longer)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoats\u003c\/th\u003e\n\u003ctd\u003e1 recommended, 2 maximum\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply with\u003c\/th\u003e\n\u003ctd\u003eSynthetic-bristle or foam brush, pad applicator, short-nap or foam roller, or spray. HVLP 1.1-1.3 mm; air-assist airless .007 in; airless fine finish .007-.009 in\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply when\u003c\/th\u003e\n\u003ctd\u003eAbout 70 F and 50% humidity, out of direct sun. GF Accelerator helps in cool or humid conditions, GF Extender in warm or dry ones.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThinning\u003c\/th\u003e\n\u003ctd\u003eDistilled water, 5% up to 10% by volume\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eClean up\u003c\/th\u003e\n\u003ctd\u003eSoap and water (hands); GF Brush \u0026amp; Gun Cleaner (equipment)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSolids\u003c\/th\u003e\n\u003ctd\u003e12-22% by volume, 14-20% by weight (varies by color)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVOC\u003c\/th\u003e\n\u003ctd\u003e165 g\/L on the Black SDS; the TDS says all colors are under 185 g\/L\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAir quality\u003c\/th\u003e\n\u003ctd\u003eSCAQMD, CARB, Canada, OTC Phase I and II compliant (TDS)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStorage\u003c\/th\u003e\n\u003ctd\u003e50-80 F, tightly sealed, out of sun; best used within a year of the date on the can\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSources\u003c\/th\u003e\n\u003ctd\u003e\n\u003ca href=\"https:\/\/generalfinishes.com\/wood-finishes-retail\/water-based-wood-stains-and-dye-stains\/water-based-wood-stain\" target=\"_blank\" rel=\"noopener\"\u003eGeneral Finishes Water-Based Wood Stain page\u003c\/a\u003e; \u003ca href=\"https:\/\/generalfinishes.com\/sites\/default\/files\/documents\/files\/2020-04\/TDS-2020-03-Water-Based-Wood-Stain-General-Finishes.pdf\" target=\"_blank\" rel=\"noopener\"\u003eTechnical data sheet (March 2020)\u003c\/a\u003e; \u003ca href=\"https:\/\/generalfinishes.com\/sites\/default\/files\/documents\/files\/2024-02\/SDS-English-Water-Based-Wood-Stain-BLACK-Water-Base-General-Finishes-US-HCS-2012-v1-2024-02-02.PDF\" target=\"_blank\" rel=\"noopener\"\u003eBlack SDS (rev. 02-Feb-2024)\u003c\/a\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\u003ch3\u003eHow much do I need?\u003c\/h3\u003e\n\u003cp\u003eGF rates the stain at up to 600 sq ft per gallon, so this pint covers up to about 75 sq ft (calculated). Porous or softer woods take more. If you plan a second coat, count it as another full pass.\u003c\/p\u003e\n\u003ch3\u003eHow to apply\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eRaw wood: sand with 120 grit, then 150 or 220 grit, and remove the dust. GF says no finer than 220 on closed-grain woods or 180 on open-grain woods. To reduce grain raise, wet the wood with water, let it dry and sand smooth before staining.\u003c\/li\u003e\n\u003cli\u003eExisting finish: scuff-clean with a non-woven pad and a 50:50 mix of denatured alcohol and water, dry 1-2 hours, then sand lightly with a 220-320 grit sponge. Remove dust and test adhesion.\u003c\/li\u003e\n\u003cli\u003eWork in a ventilated area and stir before and during use. On raw wood, apply a liberal amount to one section at a time, then wipe off the excess with the grain using absorbent terry cloth or paper towel. Do not use cotton T-shirts; they push the stain around. Correct lap marks right away by rewetting the whole section and wiping again.\u003c\/li\u003e\n\u003cli\u003eOver an existing finish, use thin coats with a foam brush or staining pad and avoid heavy build.\u003c\/li\u003e\n\u003cli\u003eLet it dry at least 2 hours (24 hours under an oil-based topcoat), then apply 3 coats of a GF topcoat. Take care not to sand through the first topcoat coat.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eGood to know\u003c\/h3\u003e\n\u003cp\u003eStain color changes with wood species, prep, lighting and the topcoat, so test the full stain-and-topcoat process on scrap first. On blotch-prone woods like pine, GF Water-Based Pre-Stain Conditioner Natural evens out color but limits how much stain soaks in, so a darker color may be needed. GF notes that California users who add more than 2% GF Extender make the stain non-compliant under SCAQMD rules. The Black SDS (rev. 02-Feb-2024) lists the mixture as not classified, with no signal word. Use the respirator GF specifies when spraying. Store between 50 and 80 F and do not pour leftovers down the drain.\u003c\/p\u003e\n\u003ch3\u003eQuestions\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eCan I use it over a finished cabinet?\u003c\/strong\u003e Yes, after cleaning, scuff-sanding and an adhesion test, using thin coats like a gel stain.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCan I put an oil-based polyurethane over it?\u003c\/strong\u003e Yes. GF says to let the stain dry 24 hours first. Oil-based topcoats can amber, so test the look.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDoes it need a topcoat?\u003c\/strong\u003e Yes. GF says the stain provides color but is not durable on its own; finish with 3 coats of a GF topcoat.\u003c\/p\u003e\n\u003ch3\u003eShop related\u003c\/h3\u003e\n\u003cp\u003eSame color, other size: \u003ca href=\"\/products\/general-finishes-water-based-stain-black-quart\"\u003eBlack Quart\u003c\/a\u003e. Other colors in this size: \u003ca href=\"\/products\/general-finishes-water-based-stain-antique-brown-pint\"\u003eAntique Brown\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-espresso-pint\"\u003eEspresso\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-graystone-pint\"\u003eGraystone\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-walnut-pint\"\u003eWalnut\u003c\/a\u003e. Even out pine with \u003ca href=\"\/products\/general-finishes-pre-stain-conditioner-natural-pint\"\u003eGF Water-Based Pre-Stain Conditioner Natural\u003c\/a\u003e. Topcoat with \u003ca href=\"\/products\/general-finishes-high-performance-water-based-topcoat-clear-satin-quart\"\u003eGF High Performance Topcoat, Satin\u003c\/a\u003e or see all sheens in \u003ca href=\"\/collections\/general-finishes-high-performance\"\u003eHigh Performance Topcoat\u003c\/a\u003e. Prep with a \u003ca href=\"\/products\/3m-softback-contour-sanding-sponge-fine-4-1-2-inch\"\u003e3M Softback sanding sponge\u003c\/a\u003e. Browse every color in \u003ca href=\"\/collections\/general-finishes-water-based-wood-stain\"\u003eGF Water-Based Wood Stain\u003c\/a\u003e, compare \u003ca href=\"\/collections\/curated-wood-stains-gel-stains\"\u003ewood stains and gel stains\u003c\/a\u003e, or plan the job with the \u003ca href=\"\/pages\/furniture-refinishing-project-cart\"\u003efurniture refinishing project cart\u003c\/a\u003e or \u003ca href=\"\/pages\/paint-cabinets-project-cart\"\u003ecabinet project cart\u003c\/a\u003e.\u003c\/p\u003e","brand":"General Finishes","offers":[{"title":"Default Title","offer_id":67673250660662,"sku":"WBPT","price":25.16,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0931\/9750\/0726\/files\/606016100576.jpg?v=1791582001"},{"product_id":"general-finishes-water-based-stain-black-quart","title":"General Finishes Water-Based Stain, Black, Quart","description":"\u003cp\u003eGeneral Finishes Water-Based Wood Stain in Black is a water-based pigmented stain for interior raw wood such as cabinets, trim, doors and furniture. General Finishes says its pigments give rich, dark, uniform color on hard-to-stain woods like maple and pine, and that it can also go over an existing finish, much like an oil-based gel stain. It is low odor, cleans up with water and is noncombustible. This is the quart (32 fl oz) can, GF item WBQT.\u003c\/p\u003e\n\u003ch3\u003eHighlights\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eOne coat is recommended; a second coat after the first is fully dry makes the color darker. GF says not to go past two coats.\u003c\/li\u003e\n\u003cli\u003eDry to the touch in 30 minutes; ready for a second coat or a water-based topcoat in 2 hours (70 F, 50% humidity). Wait 24 hours before an oil-based topcoat.\u003c\/li\u003e\n\u003cli\u003eBrush, foam brush, pad, microfiber roller or spray (HVLP 1.1-1.3 mm).\u003c\/li\u003e\n\u003cli\u003eStain gives color only; finish with 3 coats of a GF topcoat.\u003c\/li\u003e\n\u003cli\u003eThin with distilled water, starting at 5% and up to 10% by volume.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eBest for\u003c\/h3\u003e\n\u003cp\u003eIndoor cabinets, furniture, trim and doors, on raw wood or on a cleaned and scuff-sanded existing finish after an adhesion test. It is an interior stain; for outdoor wood, GF makes a separate Exterior 450 stain.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003eColor \/ size\u003c\/th\u003e\n\u003ctd\u003eBlack \/ Quart (32 fl oz)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eGF item \/ UPC\u003c\/th\u003e\n\u003ctd\u003eWBQT \/ 606016104710\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eType\u003c\/th\u003e\n\u003ctd\u003eWater-based pigmented stain, interior\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoverage\u003c\/th\u003e\n\u003ctd\u003eUp to 600 sq ft per gallon (TDS), so up to about 150 sq ft for this can (calculated)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDry times\u003c\/th\u003e\n\u003ctd\u003eTouch 30 minutes; recoat 2 hours; 24 hours before an oil-based topcoat (70 F, 50% humidity; cool, humid or thick coats take longer)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoats\u003c\/th\u003e\n\u003ctd\u003e1 recommended, 2 maximum\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply with\u003c\/th\u003e\n\u003ctd\u003eSynthetic-bristle or foam brush, pad applicator, short-nap or foam roller, or spray. HVLP 1.1-1.3 mm; air-assist airless .007 in; airless fine finish .007-.009 in\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply when\u003c\/th\u003e\n\u003ctd\u003eAbout 70 F and 50% humidity, out of direct sun. GF Accelerator helps in cool or humid conditions, GF Extender in warm or dry ones.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThinning\u003c\/th\u003e\n\u003ctd\u003eDistilled water, 5% up to 10% by volume\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eClean up\u003c\/th\u003e\n\u003ctd\u003eSoap and water (hands); GF Brush \u0026amp; Gun Cleaner (equipment)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSolids\u003c\/th\u003e\n\u003ctd\u003e12-22% by volume, 14-20% by weight (varies by color)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVOC\u003c\/th\u003e\n\u003ctd\u003e165 g\/L on the Black SDS; the TDS says all colors are under 185 g\/L\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAir quality\u003c\/th\u003e\n\u003ctd\u003eSCAQMD, CARB, Canada, OTC Phase I and II compliant (TDS)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStorage\u003c\/th\u003e\n\u003ctd\u003e50-80 F, tightly sealed, out of sun; best used within a year of the date on the can\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSources\u003c\/th\u003e\n\u003ctd\u003e\n\u003ca href=\"https:\/\/generalfinishes.com\/wood-finishes-retail\/water-based-wood-stains-and-dye-stains\/water-based-wood-stain\" target=\"_blank\" rel=\"noopener\"\u003eGeneral Finishes Water-Based Wood Stain page\u003c\/a\u003e; \u003ca href=\"https:\/\/generalfinishes.com\/sites\/default\/files\/documents\/files\/2020-04\/TDS-2020-03-Water-Based-Wood-Stain-General-Finishes.pdf\" target=\"_blank\" rel=\"noopener\"\u003eTechnical data sheet (March 2020)\u003c\/a\u003e; \u003ca href=\"https:\/\/generalfinishes.com\/sites\/default\/files\/documents\/files\/2024-02\/SDS-English-Water-Based-Wood-Stain-BLACK-Water-Base-General-Finishes-US-HCS-2012-v1-2024-02-02.PDF\" target=\"_blank\" rel=\"noopener\"\u003eBlack SDS (rev. 02-Feb-2024)\u003c\/a\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\u003ch3\u003eHow much do I need?\u003c\/h3\u003e\n\u003cp\u003eGF rates the stain at up to 600 sq ft per gallon, so this quart covers up to about 150 sq ft (calculated). Porous or softer woods take more. If you plan a second coat, count it as another full pass.\u003c\/p\u003e\n\u003ch3\u003eHow to apply\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eRaw wood: sand with 120 grit, then 150 or 220 grit, and remove the dust. GF says no finer than 220 on closed-grain woods or 180 on open-grain woods. To reduce grain raise, wet the wood with water, let it dry and sand smooth before staining.\u003c\/li\u003e\n\u003cli\u003eExisting finish: scuff-clean with a non-woven pad and a 50:50 mix of denatured alcohol and water, dry 1-2 hours, then sand lightly with a 220-320 grit sponge. Remove dust and test adhesion.\u003c\/li\u003e\n\u003cli\u003eWork in a ventilated area and stir before and during use. On raw wood, apply a liberal amount to one section at a time, then wipe off the excess with the grain using absorbent terry cloth or paper towel. Do not use cotton T-shirts; they push the stain around. Correct lap marks right away by rewetting the whole section and wiping again.\u003c\/li\u003e\n\u003cli\u003eOver an existing finish, use thin coats with a foam brush or staining pad and avoid heavy build.\u003c\/li\u003e\n\u003cli\u003eLet it dry at least 2 hours (24 hours under an oil-based topcoat), then apply 3 coats of a GF topcoat. Take care not to sand through the first topcoat coat.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eGood to know\u003c\/h3\u003e\n\u003cp\u003eStain color changes with wood species, prep, lighting and the topcoat, so test the full stain-and-topcoat process on scrap first. On blotch-prone woods like pine, GF Water-Based Pre-Stain Conditioner Natural evens out color but limits how much stain soaks in, so a darker color may be needed. GF notes that California users who add more than 2% GF Extender make the stain non-compliant under SCAQMD rules. The Black SDS (rev. 02-Feb-2024) lists the mixture as not classified, with no signal word. Use the respirator GF specifies when spraying. Store between 50 and 80 F and do not pour leftovers down the drain.\u003c\/p\u003e\n\u003ch3\u003eQuestions\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eCan I use it over a finished cabinet?\u003c\/strong\u003e Yes, after cleaning, scuff-sanding and an adhesion test, using thin coats like a gel stain.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCan I put an oil-based polyurethane over it?\u003c\/strong\u003e Yes. GF says to let the stain dry 24 hours first. Oil-based topcoats can amber, so test the look.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDoes it need a topcoat?\u003c\/strong\u003e Yes. GF says the stain provides color but is not durable on its own; finish with 3 coats of a GF topcoat.\u003c\/p\u003e\n\u003ch3\u003eShop related\u003c\/h3\u003e\n\u003cp\u003eSame color, other size: \u003ca href=\"\/products\/general-finishes-water-based-stain-black-pint\"\u003eBlack Pint\u003c\/a\u003e. Other colors in this size: \u003ca href=\"\/products\/general-finishes-water-based-stain-antique-brown-quart\"\u003eAntique Brown\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-espresso-quart\"\u003eEspresso\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-graystone-quart\"\u003eGraystone\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-walnut-quart\"\u003eWalnut\u003c\/a\u003e. Even out pine with \u003ca href=\"\/products\/general-finishes-pre-stain-conditioner-natural-quart\"\u003eGF Water-Based Pre-Stain Conditioner Natural\u003c\/a\u003e. Topcoat with \u003ca href=\"\/products\/general-finishes-high-performance-water-based-topcoat-clear-satin-quart\"\u003eGF High Performance Topcoat, Satin\u003c\/a\u003e or see all sheens in \u003ca href=\"\/collections\/general-finishes-high-performance\"\u003eHigh Performance Topcoat\u003c\/a\u003e. Prep with a \u003ca href=\"\/products\/3m-softback-contour-sanding-sponge-fine-4-1-2-inch\"\u003e3M Softback sanding sponge\u003c\/a\u003e. Browse every color in \u003ca href=\"\/collections\/general-finishes-water-based-wood-stain\"\u003eGF Water-Based Wood Stain\u003c\/a\u003e, compare \u003ca href=\"\/collections\/curated-wood-stains-gel-stains\"\u003ewood stains and gel stains\u003c\/a\u003e, or plan the job with the \u003ca href=\"\/pages\/furniture-refinishing-project-cart\"\u003efurniture refinishing project cart\u003c\/a\u003e or \u003ca href=\"\/pages\/paint-cabinets-project-cart\"\u003ecabinet project cart\u003c\/a\u003e.\u003c\/p\u003e","brand":"General Finishes","offers":[{"title":"Default Title","offer_id":67673250890038,"sku":"WBQT","price":39.46,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0931\/9750\/0726\/files\/606016104710.jpg?v=1791582004"},{"product_id":"general-finishes-water-based-stain-black-cherry-pint","title":"General Finishes Water-Based Stain, Black Cherry, Pint","description":"\u003cp\u003eGeneral Finishes Water-Based Wood Stain in Black Cherry is a water-based pigmented stain for interior raw wood such as cabinets, trim, doors and furniture. General Finishes says its pigments give rich, dark, uniform color on hard-to-stain woods like maple and pine, and that it can also go over an existing finish, much like an oil-based gel stain. It is low odor, cleans up with water and is noncombustible. This is the pint (16 fl oz) can, GF item WKPT.\u003c\/p\u003e\n\u003ch3\u003eHighlights\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eOne coat is recommended; a second coat after the first is fully dry makes the color darker. GF says not to go past two coats.\u003c\/li\u003e\n\u003cli\u003eDry to the touch in 30 minutes; ready for a second coat or a water-based topcoat in 2 hours (70 F, 50% humidity). Wait 24 hours before an oil-based topcoat.\u003c\/li\u003e\n\u003cli\u003eBrush, foam brush, pad, microfiber roller or spray (HVLP 1.1-1.3 mm).\u003c\/li\u003e\n\u003cli\u003eStain gives color only; finish with 3 coats of a GF topcoat.\u003c\/li\u003e\n\u003cli\u003eThin with distilled water, starting at 5% and up to 10% by volume.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eBest for\u003c\/h3\u003e\n\u003cp\u003eIndoor cabinets, furniture, trim and doors, on raw wood or on a cleaned and scuff-sanded existing finish after an adhesion test. It is an interior stain; for outdoor wood, GF makes a separate Exterior 450 stain.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003eColor \/ size\u003c\/th\u003e\n\u003ctd\u003eBlack Cherry \/ Pint (16 fl oz)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eGF item \/ UPC\u003c\/th\u003e\n\u003ctd\u003eWKPT \/ 606016101504\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eType\u003c\/th\u003e\n\u003ctd\u003eWater-based pigmented stain, interior\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoverage\u003c\/th\u003e\n\u003ctd\u003eUp to 600 sq ft per gallon (TDS), so up to about 75 sq ft for this can (calculated)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDry times\u003c\/th\u003e\n\u003ctd\u003eTouch 30 minutes; recoat 2 hours; 24 hours before an oil-based topcoat (70 F, 50% humidity; cool, humid or thick coats take longer)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoats\u003c\/th\u003e\n\u003ctd\u003e1 recommended, 2 maximum\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply with\u003c\/th\u003e\n\u003ctd\u003eSynthetic-bristle or foam brush, pad applicator, short-nap or foam roller, or spray. HVLP 1.1-1.3 mm; air-assist airless .007 in; airless fine finish .007-.009 in\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply when\u003c\/th\u003e\n\u003ctd\u003eAbout 70 F and 50% humidity, out of direct sun. GF Accelerator helps in cool or humid conditions, GF Extender in warm or dry ones.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThinning\u003c\/th\u003e\n\u003ctd\u003eDistilled water, 5% up to 10% by volume\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eClean up\u003c\/th\u003e\n\u003ctd\u003eSoap and water (hands); GF Brush \u0026amp; Gun Cleaner (equipment)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSolids\u003c\/th\u003e\n\u003ctd\u003e12-22% by volume, 14-20% by weight (varies by color)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVOC\u003c\/th\u003e\n\u003ctd\u003eUnder 160 g\/L on the Black Cherry SDS (rev. 02-Feb-2024); the TDS says all colors are under 185 g\/L\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAir quality\u003c\/th\u003e\n\u003ctd\u003eSCAQMD, CARB, Canada, OTC Phase I and II compliant (TDS)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStorage\u003c\/th\u003e\n\u003ctd\u003e50-80 F, tightly sealed, out of sun; best used within a year of the date on the can\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSources\u003c\/th\u003e\n\u003ctd\u003e\n\u003ca href=\"https:\/\/generalfinishes.com\/wood-finishes-retail\/water-based-wood-stains-and-dye-stains\/water-based-wood-stain\" target=\"_blank\" rel=\"noopener\"\u003eGeneral Finishes Water-Based Wood Stain page\u003c\/a\u003e; \u003ca href=\"https:\/\/generalfinishes.com\/sites\/default\/files\/documents\/files\/2020-04\/TDS-2020-03-Water-Based-Wood-Stain-General-Finishes.pdf\" target=\"_blank\" rel=\"noopener\"\u003eTechnical data sheet (March 2020)\u003c\/a\u003e; \u003ca href=\"https:\/\/generalfinishes.com\/sites\/default\/files\/documents\/files\/2024-02\/SDS-English-Water-Based-Wood-Stain-BLACK-CHERRY-Water-Base-General-Finishes-US-HCS-2012-v1-2024-02-02.PDF\" target=\"_blank\" rel=\"noopener\"\u003eBlack Cherry SDS (rev. 02-Feb-2024)\u003c\/a\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\u003ch3\u003eHow much do I need?\u003c\/h3\u003e\n\u003cp\u003eGF rates the stain at up to 600 sq ft per gallon, so this pint covers up to about 75 sq ft (calculated). Porous or softer woods take more. If you plan a second coat, count it as another full pass.\u003c\/p\u003e\n\u003ch3\u003eHow to apply\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eRaw wood: sand with 120 grit, then 150 or 220 grit, and remove the dust. GF says no finer than 220 on closed-grain woods or 180 on open-grain woods. To reduce grain raise, wet the wood with water, let it dry and sand smooth before staining.\u003c\/li\u003e\n\u003cli\u003eExisting finish: scuff-clean with a non-woven pad and a 50:50 mix of denatured alcohol and water, dry 1-2 hours, then sand lightly with a 220-320 grit sponge. Remove dust and test adhesion.\u003c\/li\u003e\n\u003cli\u003eWork in a ventilated area and stir before and during use. On raw wood, apply a liberal amount to one section at a time, then wipe off the excess with the grain using absorbent terry cloth or paper towel. Do not use cotton T-shirts; they push the stain around. Correct lap marks right away by rewetting the whole section and wiping again.\u003c\/li\u003e\n\u003cli\u003eOver an existing finish, use thin coats with a foam brush or staining pad and avoid heavy build.\u003c\/li\u003e\n\u003cli\u003eLet it dry at least 2 hours (24 hours under an oil-based topcoat), then apply 3 coats of a GF topcoat. Take care not to sand through the first topcoat coat.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eGood to know\u003c\/h3\u003e\n\u003cp\u003eStain color changes with wood species, prep, lighting and the topcoat, so test the full stain-and-topcoat process on scrap first. On blotch-prone woods like pine, GF Water-Based Pre-Stain Conditioner Natural evens out color but limits how much stain soaks in, so a darker color may be needed. GF notes that California users who add more than 2% GF Extender make the stain non-compliant under SCAQMD rules. The Black Cherry SDS (rev. 02-Feb-2024) uses the signal word Danger: may cause cancer. Wear the protection it lists, and use the respirator GF specifies when spraying. Store between 50 and 80 F and do not pour leftovers down the drain.\u003c\/p\u003e\n\u003ch3\u003eQuestions\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eCan I use it over a finished cabinet?\u003c\/strong\u003e Yes, after cleaning, scuff-sanding and an adhesion test, using thin coats like a gel stain.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCan I put an oil-based polyurethane over it?\u003c\/strong\u003e Yes. GF says to let the stain dry 24 hours first. Oil-based topcoats can amber, so test the look.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDoes it need a topcoat?\u003c\/strong\u003e Yes. GF says the stain provides color but is not durable on its own; finish with 3 coats of a GF topcoat.\u003c\/p\u003e\n\u003ch3\u003eShop related\u003c\/h3\u003e\n\u003cp\u003eSame color, other size: \u003ca href=\"\/products\/general-finishes-water-based-stain-black-cherry-quart\"\u003eBlack Cherry Quart\u003c\/a\u003e. Other colors in this size: \u003ca href=\"\/products\/general-finishes-water-based-stain-antique-brown-pint\"\u003eAntique Brown\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-antique-oak-pint\"\u003eAntique Oak\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-black-pint\"\u003eBlack\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-brown-mahogany-pint\"\u003eBrown Mahogany\u003c\/a\u003e. Even out pine with \u003ca href=\"\/products\/general-finishes-pre-stain-conditioner-natural-pint\"\u003eGF Water-Based Pre-Stain Conditioner Natural\u003c\/a\u003e. Topcoat with \u003ca href=\"\/products\/general-finishes-high-performance-water-based-topcoat-clear-satin-quart\"\u003eGF High Performance Topcoat, Satin\u003c\/a\u003e or see all sheens in \u003ca href=\"\/collections\/general-finishes-high-performance\"\u003eHigh Performance Topcoat\u003c\/a\u003e. Prep with a \u003ca href=\"\/products\/3m-softback-contour-sanding-sponge-fine-4-1-2-inch\"\u003e3M Softback sanding sponge\u003c\/a\u003e. Browse every color in \u003ca href=\"\/collections\/general-finishes-water-based-wood-stain\"\u003eGF Water-Based Wood Stain\u003c\/a\u003e, compare \u003ca href=\"\/collections\/curated-wood-stains-gel-stains\"\u003ewood stains and gel stains\u003c\/a\u003e, or plan the job with the \u003ca href=\"\/pages\/furniture-refinishing-project-cart\"\u003efurniture refinishing project cart\u003c\/a\u003e or \u003ca href=\"\/pages\/paint-cabinets-project-cart\"\u003ecabinet project cart\u003c\/a\u003e.\u003c\/p\u003e","brand":"General Finishes","offers":[{"title":"Default Title","offer_id":67673250955574,"sku":"WKPT","price":25.16,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0931\/9750\/0726\/files\/606016101504.jpg?v=1791582006"},{"product_id":"general-finishes-water-based-stain-black-cherry-quart","title":"General Finishes Water-Based Stain, Black Cherry, Quart","description":"\u003cp\u003eGeneral Finishes Water-Based Wood Stain in Black Cherry is a water-based pigmented stain for interior raw wood such as cabinets, trim, doors and furniture. General Finishes says its pigments give rich, dark, uniform color on hard-to-stain woods like maple and pine, and that it can also go over an existing finish, much like an oil-based gel stain. It is low odor, cleans up with water and is noncombustible. This is the quart (32 fl oz) can, GF item WKQT.\u003c\/p\u003e\n\u003ch3\u003eHighlights\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eOne coat is recommended; a second coat after the first is fully dry makes the color darker. GF says not to go past two coats.\u003c\/li\u003e\n\u003cli\u003eDry to the touch in 30 minutes; ready for a second coat or a water-based topcoat in 2 hours (70 F, 50% humidity). Wait 24 hours before an oil-based topcoat.\u003c\/li\u003e\n\u003cli\u003eBrush, foam brush, pad, microfiber roller or spray (HVLP 1.1-1.3 mm).\u003c\/li\u003e\n\u003cli\u003eStain gives color only; finish with 3 coats of a GF topcoat.\u003c\/li\u003e\n\u003cli\u003eThin with distilled water, starting at 5% and up to 10% by volume.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eBest for\u003c\/h3\u003e\n\u003cp\u003eIndoor cabinets, furniture, trim and doors, on raw wood or on a cleaned and scuff-sanded existing finish after an adhesion test. It is an interior stain; for outdoor wood, GF makes a separate Exterior 450 stain.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003eColor \/ size\u003c\/th\u003e\n\u003ctd\u003eBlack Cherry \/ Quart (32 fl oz)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eGF item \/ UPC\u003c\/th\u003e\n\u003ctd\u003eWKQT \/ 606016101511\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eType\u003c\/th\u003e\n\u003ctd\u003eWater-based pigmented stain, interior\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoverage\u003c\/th\u003e\n\u003ctd\u003eUp to 600 sq ft per gallon (TDS), so up to about 150 sq ft for this can (calculated)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDry times\u003c\/th\u003e\n\u003ctd\u003eTouch 30 minutes; recoat 2 hours; 24 hours before an oil-based topcoat (70 F, 50% humidity; cool, humid or thick coats take longer)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoats\u003c\/th\u003e\n\u003ctd\u003e1 recommended, 2 maximum\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply with\u003c\/th\u003e\n\u003ctd\u003eSynthetic-bristle or foam brush, pad applicator, short-nap or foam roller, or spray. HVLP 1.1-1.3 mm; air-assist airless .007 in; airless fine finish .007-.009 in\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply when\u003c\/th\u003e\n\u003ctd\u003eAbout 70 F and 50% humidity, out of direct sun. GF Accelerator helps in cool or humid conditions, GF Extender in warm or dry ones.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThinning\u003c\/th\u003e\n\u003ctd\u003eDistilled water, 5% up to 10% by volume\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eClean up\u003c\/th\u003e\n\u003ctd\u003eSoap and water (hands); GF Brush \u0026amp; Gun Cleaner (equipment)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSolids\u003c\/th\u003e\n\u003ctd\u003e12-22% by volume, 14-20% by weight (varies by color)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVOC\u003c\/th\u003e\n\u003ctd\u003eUnder 160 g\/L on the Black Cherry SDS (rev. 02-Feb-2024); the TDS says all colors are under 185 g\/L\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAir quality\u003c\/th\u003e\n\u003ctd\u003eSCAQMD, CARB, Canada, OTC Phase I and II compliant (TDS)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStorage\u003c\/th\u003e\n\u003ctd\u003e50-80 F, tightly sealed, out of sun; best used within a year of the date on the can\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSources\u003c\/th\u003e\n\u003ctd\u003e\n\u003ca href=\"https:\/\/generalfinishes.com\/wood-finishes-retail\/water-based-wood-stains-and-dye-stains\/water-based-wood-stain\" target=\"_blank\" rel=\"noopener\"\u003eGeneral Finishes Water-Based Wood Stain page\u003c\/a\u003e; \u003ca href=\"https:\/\/generalfinishes.com\/sites\/default\/files\/documents\/files\/2020-04\/TDS-2020-03-Water-Based-Wood-Stain-General-Finishes.pdf\" target=\"_blank\" rel=\"noopener\"\u003eTechnical data sheet (March 2020)\u003c\/a\u003e; \u003ca href=\"https:\/\/generalfinishes.com\/sites\/default\/files\/documents\/files\/2024-02\/SDS-English-Water-Based-Wood-Stain-BLACK-CHERRY-Water-Base-General-Finishes-US-HCS-2012-v1-2024-02-02.PDF\" target=\"_blank\" rel=\"noopener\"\u003eBlack Cherry SDS (rev. 02-Feb-2024)\u003c\/a\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\u003ch3\u003eHow much do I need?\u003c\/h3\u003e\n\u003cp\u003eGF rates the stain at up to 600 sq ft per gallon, so this quart covers up to about 150 sq ft (calculated). Porous or softer woods take more. If you plan a second coat, count it as another full pass.\u003c\/p\u003e\n\u003ch3\u003eHow to apply\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eRaw wood: sand with 120 grit, then 150 or 220 grit, and remove the dust. GF says no finer than 220 on closed-grain woods or 180 on open-grain woods. To reduce grain raise, wet the wood with water, let it dry and sand smooth before staining.\u003c\/li\u003e\n\u003cli\u003eExisting finish: scuff-clean with a non-woven pad and a 50:50 mix of denatured alcohol and water, dry 1-2 hours, then sand lightly with a 220-320 grit sponge. Remove dust and test adhesion.\u003c\/li\u003e\n\u003cli\u003eWork in a ventilated area and stir before and during use. On raw wood, apply a liberal amount to one section at a time, then wipe off the excess with the grain using absorbent terry cloth or paper towel. Do not use cotton T-shirts; they push the stain around. Correct lap marks right away by rewetting the whole section and wiping again.\u003c\/li\u003e\n\u003cli\u003eOver an existing finish, use thin coats with a foam brush or staining pad and avoid heavy build.\u003c\/li\u003e\n\u003cli\u003eLet it dry at least 2 hours (24 hours under an oil-based topcoat), then apply 3 coats of a GF topcoat. Take care not to sand through the first topcoat coat.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eGood to know\u003c\/h3\u003e\n\u003cp\u003eStain color changes with wood species, prep, lighting and the topcoat, so test the full stain-and-topcoat process on scrap first. On blotch-prone woods like pine, GF Water-Based Pre-Stain Conditioner Natural evens out color but limits how much stain soaks in, so a darker color may be needed. GF notes that California users who add more than 2% GF Extender make the stain non-compliant under SCAQMD rules. The Black Cherry SDS (rev. 02-Feb-2024) uses the signal word Danger: may cause cancer. Wear the protection it lists, and use the respirator GF specifies when spraying. Store between 50 and 80 F and do not pour leftovers down the drain.\u003c\/p\u003e\n\u003ch3\u003eQuestions\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eCan I use it over a finished cabinet?\u003c\/strong\u003e Yes, after cleaning, scuff-sanding and an adhesion test, using thin coats like a gel stain.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCan I put an oil-based polyurethane over it?\u003c\/strong\u003e Yes. GF says to let the stain dry 24 hours first. Oil-based topcoats can amber, so test the look.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDoes it need a topcoat?\u003c\/strong\u003e Yes. GF says the stain provides color but is not durable on its own; finish with 3 coats of a GF topcoat.\u003c\/p\u003e\n\u003ch3\u003eShop related\u003c\/h3\u003e\n\u003cp\u003eSame color, other size: \u003ca href=\"\/products\/general-finishes-water-based-stain-black-cherry-pint\"\u003eBlack Cherry Pint\u003c\/a\u003e. Other colors in this size: \u003ca href=\"\/products\/general-finishes-water-based-stain-antique-brown-quart\"\u003eAntique Brown\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-antique-oak-quart\"\u003eAntique Oak\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-black-quart\"\u003eBlack\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-brown-mahogany-quart\"\u003eBrown Mahogany\u003c\/a\u003e. Even out pine with \u003ca href=\"\/products\/general-finishes-pre-stain-conditioner-natural-quart\"\u003eGF Water-Based Pre-Stain Conditioner Natural\u003c\/a\u003e. Topcoat with \u003ca href=\"\/products\/general-finishes-high-performance-water-based-topcoat-clear-satin-quart\"\u003eGF High Performance Topcoat, Satin\u003c\/a\u003e or see all sheens in \u003ca href=\"\/collections\/general-finishes-high-performance\"\u003eHigh Performance Topcoat\u003c\/a\u003e. Prep with a \u003ca href=\"\/products\/3m-softback-contour-sanding-sponge-fine-4-1-2-inch\"\u003e3M Softback sanding sponge\u003c\/a\u003e. Browse every color in \u003ca href=\"\/collections\/general-finishes-water-based-wood-stain\"\u003eGF Water-Based Wood Stain\u003c\/a\u003e, compare \u003ca href=\"\/collections\/curated-wood-stains-gel-stains\"\u003ewood stains and gel stains\u003c\/a\u003e, or plan the job with the \u003ca href=\"\/pages\/furniture-refinishing-project-cart\"\u003efurniture refinishing project cart\u003c\/a\u003e or \u003ca href=\"\/pages\/paint-cabinets-project-cart\"\u003ecabinet project cart\u003c\/a\u003e.\u003c\/p\u003e","brand":"General Finishes","offers":[{"title":"Default Title","offer_id":67673250988342,"sku":"WKQT","price":39.46,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0931\/9750\/0726\/files\/606016101511.jpg?v=1791582008"},{"product_id":"general-finishes-water-based-stain-brown-mahogany-pint","title":"General Finishes Water-Based Stain, Brown Mahogany, Pint","description":"\u003cp\u003eGeneral Finishes Water-Based Wood Stain in Brown Mahogany is a water-based pigmented stain for interior raw wood such as cabinets, trim, doors and furniture. General Finishes says its pigments give rich, dark, uniform color on hard-to-stain woods like maple and pine, and that it can also go over an existing finish, much like an oil-based gel stain. It is low odor, cleans up with water and is noncombustible. This is the pint (16 fl oz) can, GF item WYPT.\u003c\/p\u003e\n\u003ch3\u003eHighlights\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eOne coat is recommended; a second coat after the first is fully dry makes the color darker. GF says not to go past two coats.\u003c\/li\u003e\n\u003cli\u003eDry to the touch in 30 minutes; ready for a second coat or a water-based topcoat in 2 hours (70 F, 50% humidity). Wait 24 hours before an oil-based topcoat.\u003c\/li\u003e\n\u003cli\u003eBrush, foam brush, pad, microfiber roller or spray (HVLP 1.1-1.3 mm).\u003c\/li\u003e\n\u003cli\u003eStain gives color only; finish with 3 coats of a GF topcoat.\u003c\/li\u003e\n\u003cli\u003eThin with distilled water, starting at 5% and up to 10% by volume.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eBest for\u003c\/h3\u003e\n\u003cp\u003eIndoor cabinets, furniture, trim and doors, on raw wood or on a cleaned and scuff-sanded existing finish after an adhesion test. It is an interior stain; for outdoor wood, GF makes a separate Exterior 450 stain.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003eColor \/ size\u003c\/th\u003e\n\u003ctd\u003eBrown Mahogany \/ Pint (16 fl oz)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eGF item \/ UPC\u003c\/th\u003e\n\u003ctd\u003eWYPT \/ 606016100088\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eType\u003c\/th\u003e\n\u003ctd\u003eWater-based pigmented stain, interior\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoverage\u003c\/th\u003e\n\u003ctd\u003eUp to 600 sq ft per gallon (TDS), so up to about 75 sq ft for this can (calculated)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDry times\u003c\/th\u003e\n\u003ctd\u003eTouch 30 minutes; recoat 2 hours; 24 hours before an oil-based topcoat (70 F, 50% humidity; cool, humid or thick coats take longer)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoats\u003c\/th\u003e\n\u003ctd\u003e1 recommended, 2 maximum\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply with\u003c\/th\u003e\n\u003ctd\u003eSynthetic-bristle or foam brush, pad applicator, short-nap or foam roller, or spray. HVLP 1.1-1.3 mm; air-assist airless .007 in; airless fine finish .007-.009 in\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply when\u003c\/th\u003e\n\u003ctd\u003eAbout 70 F and 50% humidity, out of direct sun. GF Accelerator helps in cool or humid conditions, GF Extender in warm or dry ones.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThinning\u003c\/th\u003e\n\u003ctd\u003eDistilled water, 5% up to 10% by volume\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eClean up\u003c\/th\u003e\n\u003ctd\u003eSoap and water (hands); GF Brush \u0026amp; Gun Cleaner (equipment)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSolids\u003c\/th\u003e\n\u003ctd\u003e12-22% by volume, 14-20% by weight (varies by color)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVOC\u003c\/th\u003e\n\u003ctd\u003eUnder 160 g\/L on the Brown Mahogany SDS (rev. 02-Feb-2024); the TDS says all colors are under 185 g\/L\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAir quality\u003c\/th\u003e\n\u003ctd\u003eSCAQMD, CARB, Canada, OTC Phase I and II compliant (TDS)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStorage\u003c\/th\u003e\n\u003ctd\u003e50-80 F, tightly sealed, out of sun; best used within a year of the date on the can\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSources\u003c\/th\u003e\n\u003ctd\u003e\n\u003ca href=\"https:\/\/generalfinishes.com\/wood-finishes-retail\/water-based-wood-stains-and-dye-stains\/water-based-wood-stain\" target=\"_blank\" rel=\"noopener\"\u003eGeneral Finishes Water-Based Wood Stain page\u003c\/a\u003e; \u003ca href=\"https:\/\/generalfinishes.com\/sites\/default\/files\/documents\/files\/2020-04\/TDS-2020-03-Water-Based-Wood-Stain-General-Finishes.pdf\" target=\"_blank\" rel=\"noopener\"\u003eTechnical data sheet (March 2020)\u003c\/a\u003e; \u003ca href=\"https:\/\/generalfinishes.com\/sites\/default\/files\/documents\/files\/2024-02\/SDS-English-Water-Based-Wood-Stain-BROWN-MAHOGANY-Water-Base-General-Finishes-US-HCS-2012-v1-2024-02-02.PDF\" target=\"_blank\" rel=\"noopener\"\u003eBrown Mahogany SDS (rev. 02-Feb-2024)\u003c\/a\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\u003ch3\u003eHow much do I need?\u003c\/h3\u003e\n\u003cp\u003eGF rates the stain at up to 600 sq ft per gallon, so this pint covers up to about 75 sq ft (calculated). Porous or softer woods take more. If you plan a second coat, count it as another full pass.\u003c\/p\u003e\n\u003ch3\u003eHow to apply\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eRaw wood: sand with 120 grit, then 150 or 220 grit, and remove the dust. GF says no finer than 220 on closed-grain woods or 180 on open-grain woods. To reduce grain raise, wet the wood with water, let it dry and sand smooth before staining.\u003c\/li\u003e\n\u003cli\u003eExisting finish: scuff-clean with a non-woven pad and a 50:50 mix of denatured alcohol and water, dry 1-2 hours, then sand lightly with a 220-320 grit sponge. Remove dust and test adhesion.\u003c\/li\u003e\n\u003cli\u003eWork in a ventilated area and stir before and during use. On raw wood, apply a liberal amount to one section at a time, then wipe off the excess with the grain using absorbent terry cloth or paper towel. Do not use cotton T-shirts; they push the stain around. Correct lap marks right away by rewetting the whole section and wiping again.\u003c\/li\u003e\n\u003cli\u003eOver an existing finish, use thin coats with a foam brush or staining pad and avoid heavy build.\u003c\/li\u003e\n\u003cli\u003eLet it dry at least 2 hours (24 hours under an oil-based topcoat), then apply 3 coats of a GF topcoat. Take care not to sand through the first topcoat coat.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eGood to know\u003c\/h3\u003e\n\u003cp\u003eStain color changes with wood species, prep, lighting and the topcoat, so test the full stain-and-topcoat process on scrap first. On blotch-prone woods like pine, GF Water-Based Pre-Stain Conditioner Natural evens out color but limits how much stain soaks in, so a darker color may be needed. GF notes that California users who add more than 2% GF Extender make the stain non-compliant under SCAQMD rules. The Brown Mahogany SDS (rev. 02-Feb-2024) uses the signal word Danger: may cause cancer. Wear the protection it lists, and use the respirator GF specifies when spraying. Store between 50 and 80 F and do not pour leftovers down the drain.\u003c\/p\u003e\n\u003ch3\u003eQuestions\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eCan I use it over a finished cabinet?\u003c\/strong\u003e Yes, after cleaning, scuff-sanding and an adhesion test, using thin coats like a gel stain.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCan I put an oil-based polyurethane over it?\u003c\/strong\u003e Yes. GF says to let the stain dry 24 hours first. Oil-based topcoats can amber, so test the look.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDoes it need a topcoat?\u003c\/strong\u003e Yes. GF says the stain provides color but is not durable on its own; finish with 3 coats of a GF topcoat.\u003c\/p\u003e\n\u003ch3\u003eShop related\u003c\/h3\u003e\n\u003cp\u003eSame color, other size: \u003ca href=\"\/products\/general-finishes-water-based-stain-brown-mahogany-quart\"\u003eBrown Mahogany Quart\u003c\/a\u003e. Other colors in this size: \u003ca href=\"\/products\/general-finishes-water-based-stain-antique-brown-pint\"\u003eAntique Brown\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-antique-oak-pint\"\u003eAntique Oak\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-black-pint\"\u003eBlack\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-black-cherry-pint\"\u003eBlack Cherry\u003c\/a\u003e. Even out pine with \u003ca href=\"\/products\/general-finishes-pre-stain-conditioner-natural-pint\"\u003eGF Water-Based Pre-Stain Conditioner Natural\u003c\/a\u003e. Topcoat with \u003ca href=\"\/products\/general-finishes-high-performance-water-based-topcoat-clear-satin-quart\"\u003eGF High Performance Topcoat, Satin\u003c\/a\u003e or see all sheens in \u003ca href=\"\/collections\/general-finishes-high-performance\"\u003eHigh Performance Topcoat\u003c\/a\u003e. Prep with a \u003ca href=\"\/products\/3m-softback-contour-sanding-sponge-fine-4-1-2-inch\"\u003e3M Softback sanding sponge\u003c\/a\u003e. Browse every color in \u003ca href=\"\/collections\/general-finishes-water-based-wood-stain\"\u003eGF Water-Based Wood Stain\u003c\/a\u003e, compare \u003ca href=\"\/collections\/curated-wood-stains-gel-stains\"\u003ewood stains and gel stains\u003c\/a\u003e, or plan the job with the \u003ca href=\"\/pages\/furniture-refinishing-project-cart\"\u003efurniture refinishing project cart\u003c\/a\u003e or \u003ca href=\"\/pages\/paint-cabinets-project-cart\"\u003ecabinet project cart\u003c\/a\u003e.\u003c\/p\u003e","brand":"General Finishes","offers":[{"title":"Default Title","offer_id":67673251021110,"sku":"WYPT","price":25.16,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0931\/9750\/0726\/files\/606016100088.jpg?v=1791582010"},{"product_id":"general-finishes-water-based-stain-brown-mahogany-quart","title":"General Finishes Water-Based Stain, Brown Mahogany, Quart","description":"\u003cp\u003eGeneral Finishes Water-Based Wood Stain in Brown Mahogany is a water-based pigmented stain for interior raw wood such as cabinets, trim, doors and furniture. General Finishes says its pigments give rich, dark, uniform color on hard-to-stain woods like maple and pine, and that it can also go over an existing finish, much like an oil-based gel stain. It is low odor, cleans up with water and is noncombustible. This is the quart (32 fl oz) can, GF item WYQT.\u003c\/p\u003e\n\u003ch3\u003eHighlights\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eOne coat is recommended; a second coat after the first is fully dry makes the color darker. GF says not to go past two coats.\u003c\/li\u003e\n\u003cli\u003eDry to the touch in 30 minutes; ready for a second coat or a water-based topcoat in 2 hours (70 F, 50% humidity). Wait 24 hours before an oil-based topcoat.\u003c\/li\u003e\n\u003cli\u003eBrush, foam brush, pad, microfiber roller or spray (HVLP 1.1-1.3 mm).\u003c\/li\u003e\n\u003cli\u003eStain gives color only; finish with 3 coats of a GF topcoat.\u003c\/li\u003e\n\u003cli\u003eThin with distilled water, starting at 5% and up to 10% by volume.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eBest for\u003c\/h3\u003e\n\u003cp\u003eIndoor cabinets, furniture, trim and doors, on raw wood or on a cleaned and scuff-sanded existing finish after an adhesion test. It is an interior stain; for outdoor wood, GF makes a separate Exterior 450 stain.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003eColor \/ size\u003c\/th\u003e\n\u003ctd\u003eBrown Mahogany \/ Quart (32 fl oz)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eGF item \/ UPC\u003c\/th\u003e\n\u003ctd\u003eWYQT \/ 606016100255\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eType\u003c\/th\u003e\n\u003ctd\u003eWater-based pigmented stain, interior\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoverage\u003c\/th\u003e\n\u003ctd\u003eUp to 600 sq ft per gallon (TDS), so up to about 150 sq ft for this can (calculated)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDry times\u003c\/th\u003e\n\u003ctd\u003eTouch 30 minutes; recoat 2 hours; 24 hours before an oil-based topcoat (70 F, 50% humidity; cool, humid or thick coats take longer)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoats\u003c\/th\u003e\n\u003ctd\u003e1 recommended, 2 maximum\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply with\u003c\/th\u003e\n\u003ctd\u003eSynthetic-bristle or foam brush, pad applicator, short-nap or foam roller, or spray. HVLP 1.1-1.3 mm; air-assist airless .007 in; airless fine finish .007-.009 in\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply when\u003c\/th\u003e\n\u003ctd\u003eAbout 70 F and 50% humidity, out of direct sun. GF Accelerator helps in cool or humid conditions, GF Extender in warm or dry ones.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThinning\u003c\/th\u003e\n\u003ctd\u003eDistilled water, 5% up to 10% by volume\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eClean up\u003c\/th\u003e\n\u003ctd\u003eSoap and water (hands); GF Brush \u0026amp; Gun Cleaner (equipment)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSolids\u003c\/th\u003e\n\u003ctd\u003e12-22% by volume, 14-20% by weight (varies by color)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVOC\u003c\/th\u003e\n\u003ctd\u003eUnder 160 g\/L on the Brown Mahogany SDS (rev. 02-Feb-2024); the TDS says all colors are under 185 g\/L\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAir quality\u003c\/th\u003e\n\u003ctd\u003eSCAQMD, CARB, Canada, OTC Phase I and II compliant (TDS)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStorage\u003c\/th\u003e\n\u003ctd\u003e50-80 F, tightly sealed, out of sun; best used within a year of the date on the can\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSources\u003c\/th\u003e\n\u003ctd\u003e\n\u003ca href=\"https:\/\/generalfinishes.com\/wood-finishes-retail\/water-based-wood-stains-and-dye-stains\/water-based-wood-stain\" target=\"_blank\" rel=\"noopener\"\u003eGeneral Finishes Water-Based Wood Stain page\u003c\/a\u003e; \u003ca href=\"https:\/\/generalfinishes.com\/sites\/default\/files\/documents\/files\/2020-04\/TDS-2020-03-Water-Based-Wood-Stain-General-Finishes.pdf\" target=\"_blank\" rel=\"noopener\"\u003eTechnical data sheet (March 2020)\u003c\/a\u003e; \u003ca href=\"https:\/\/generalfinishes.com\/sites\/default\/files\/documents\/files\/2024-02\/SDS-English-Water-Based-Wood-Stain-BROWN-MAHOGANY-Water-Base-General-Finishes-US-HCS-2012-v1-2024-02-02.PDF\" target=\"_blank\" rel=\"noopener\"\u003eBrown Mahogany SDS (rev. 02-Feb-2024)\u003c\/a\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\u003ch3\u003eHow much do I need?\u003c\/h3\u003e\n\u003cp\u003eGF rates the stain at up to 600 sq ft per gallon, so this quart covers up to about 150 sq ft (calculated). Porous or softer woods take more. If you plan a second coat, count it as another full pass.\u003c\/p\u003e\n\u003ch3\u003eHow to apply\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eRaw wood: sand with 120 grit, then 150 or 220 grit, and remove the dust. GF says no finer than 220 on closed-grain woods or 180 on open-grain woods. To reduce grain raise, wet the wood with water, let it dry and sand smooth before staining.\u003c\/li\u003e\n\u003cli\u003eExisting finish: scuff-clean with a non-woven pad and a 50:50 mix of denatured alcohol and water, dry 1-2 hours, then sand lightly with a 220-320 grit sponge. Remove dust and test adhesion.\u003c\/li\u003e\n\u003cli\u003eWork in a ventilated area and stir before and during use. On raw wood, apply a liberal amount to one section at a time, then wipe off the excess with the grain using absorbent terry cloth or paper towel. Do not use cotton T-shirts; they push the stain around. Correct lap marks right away by rewetting the whole section and wiping again.\u003c\/li\u003e\n\u003cli\u003eOver an existing finish, use thin coats with a foam brush or staining pad and avoid heavy build.\u003c\/li\u003e\n\u003cli\u003eLet it dry at least 2 hours (24 hours under an oil-based topcoat), then apply 3 coats of a GF topcoat. Take care not to sand through the first topcoat coat.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eGood to know\u003c\/h3\u003e\n\u003cp\u003eStain color changes with wood species, prep, lighting and the topcoat, so test the full stain-and-topcoat process on scrap first. On blotch-prone woods like pine, GF Water-Based Pre-Stain Conditioner Natural evens out color but limits how much stain soaks in, so a darker color may be needed. GF notes that California users who add more than 2% GF Extender make the stain non-compliant under SCAQMD rules. The Brown Mahogany SDS (rev. 02-Feb-2024) uses the signal word Danger: may cause cancer. Wear the protection it lists, and use the respirator GF specifies when spraying. Store between 50 and 80 F and do not pour leftovers down the drain.\u003c\/p\u003e\n\u003ch3\u003eQuestions\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eCan I use it over a finished cabinet?\u003c\/strong\u003e Yes, after cleaning, scuff-sanding and an adhesion test, using thin coats like a gel stain.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCan I put an oil-based polyurethane over it?\u003c\/strong\u003e Yes. GF says to let the stain dry 24 hours first. Oil-based topcoats can amber, so test the look.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDoes it need a topcoat?\u003c\/strong\u003e Yes. GF says the stain provides color but is not durable on its own; finish with 3 coats of a GF topcoat.\u003c\/p\u003e\n\u003ch3\u003eShop related\u003c\/h3\u003e\n\u003cp\u003eSame color, other size: \u003ca href=\"\/products\/general-finishes-water-based-stain-brown-mahogany-pint\"\u003eBrown Mahogany Pint\u003c\/a\u003e. Other colors in this size: \u003ca href=\"\/products\/general-finishes-water-based-stain-antique-brown-quart\"\u003eAntique Brown\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-antique-oak-quart\"\u003eAntique Oak\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-black-quart\"\u003eBlack\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-black-cherry-quart\"\u003eBlack Cherry\u003c\/a\u003e. Even out pine with \u003ca href=\"\/products\/general-finishes-pre-stain-conditioner-natural-quart\"\u003eGF Water-Based Pre-Stain Conditioner Natural\u003c\/a\u003e. Topcoat with \u003ca href=\"\/products\/general-finishes-high-performance-water-based-topcoat-clear-satin-quart\"\u003eGF High Performance Topcoat, Satin\u003c\/a\u003e or see all sheens in \u003ca href=\"\/collections\/general-finishes-high-performance\"\u003eHigh Performance Topcoat\u003c\/a\u003e. Prep with a \u003ca href=\"\/products\/3m-softback-contour-sanding-sponge-fine-4-1-2-inch\"\u003e3M Softback sanding sponge\u003c\/a\u003e. Browse every color in \u003ca href=\"\/collections\/general-finishes-water-based-wood-stain\"\u003eGF Water-Based Wood Stain\u003c\/a\u003e, compare \u003ca href=\"\/collections\/curated-wood-stains-gel-stains\"\u003ewood stains and gel stains\u003c\/a\u003e, or plan the job with the \u003ca href=\"\/pages\/furniture-refinishing-project-cart\"\u003efurniture refinishing project cart\u003c\/a\u003e or \u003ca href=\"\/pages\/paint-cabinets-project-cart\"\u003ecabinet project cart\u003c\/a\u003e.\u003c\/p\u003e","brand":"General Finishes","offers":[{"title":"Default Title","offer_id":67673251053878,"sku":"WYQT","price":39.46,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0931\/9750\/0726\/files\/606016100255.jpg?v=1791582011"},{"product_id":"general-finishes-water-based-stain-espresso-pint","title":"General Finishes Water-Based Stain, Espresso, Pint","description":"\u003cp\u003eGeneral Finishes Water-Based Wood Stain in Espresso is a water-based pigmented stain for interior raw wood such as cabinets, trim, doors and furniture. General Finishes says its pigments give rich, dark, uniform color on hard-to-stain woods like maple and pine, and that it can also go over an existing finish, much like an oil-based gel stain. It is low odor, cleans up with water and is noncombustible. This is the pint (16 fl oz) can, GF item WXPT.\u003c\/p\u003e\n\u003ch3\u003eHighlights\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eOne coat is recommended; a second coat after the first is fully dry makes the color darker. GF says not to go past two coats.\u003c\/li\u003e\n\u003cli\u003eDry to the touch in 30 minutes; ready for a second coat or a water-based topcoat in 2 hours (70 F, 50% humidity). Wait 24 hours before an oil-based topcoat.\u003c\/li\u003e\n\u003cli\u003eBrush, foam brush, pad, microfiber roller or spray (HVLP 1.1-1.3 mm).\u003c\/li\u003e\n\u003cli\u003eStain gives color only; finish with 3 coats of a GF topcoat.\u003c\/li\u003e\n\u003cli\u003eThin with distilled water, starting at 5% and up to 10% by volume.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eBest for\u003c\/h3\u003e\n\u003cp\u003eIndoor cabinets, furniture, trim and doors, on raw wood or on a cleaned and scuff-sanded existing finish after an adhesion test. It is an interior stain; for outdoor wood, GF makes a separate Exterior 450 stain.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003eColor \/ size\u003c\/th\u003e\n\u003ctd\u003eEspresso \/ Pint (16 fl oz)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eGF item \/ UPC\u003c\/th\u003e\n\u003ctd\u003eWXPT \/ 606016102327\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eType\u003c\/th\u003e\n\u003ctd\u003eWater-based pigmented stain, interior\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoverage\u003c\/th\u003e\n\u003ctd\u003eUp to 600 sq ft per gallon (TDS), so up to about 75 sq ft for this can (calculated)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDry times\u003c\/th\u003e\n\u003ctd\u003eTouch 30 minutes; recoat 2 hours; 24 hours before an oil-based topcoat (70 F, 50% humidity; cool, humid or thick coats take longer)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoats\u003c\/th\u003e\n\u003ctd\u003e1 recommended, 2 maximum\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply with\u003c\/th\u003e\n\u003ctd\u003eSynthetic-bristle or foam brush, pad applicator, short-nap or foam roller, or spray. HVLP 1.1-1.3 mm; air-assist airless .007 in; airless fine finish .007-.009 in\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply when\u003c\/th\u003e\n\u003ctd\u003eAbout 70 F and 50% humidity, out of direct sun. GF Accelerator helps in cool or humid conditions, GF Extender in warm or dry ones.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThinning\u003c\/th\u003e\n\u003ctd\u003eDistilled water, 5% up to 10% by volume\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eClean up\u003c\/th\u003e\n\u003ctd\u003eSoap and water (hands); GF Brush \u0026amp; Gun Cleaner (equipment)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSolids\u003c\/th\u003e\n\u003ctd\u003e12-22% by volume, 14-20% by weight (varies by color)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVOC\u003c\/th\u003e\n\u003ctd\u003e160 g\/L on the Espresso SDS; the TDS says all colors are under 185 g\/L\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAir quality\u003c\/th\u003e\n\u003ctd\u003eSCAQMD, CARB, Canada, OTC Phase I and II compliant (TDS)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStorage\u003c\/th\u003e\n\u003ctd\u003e50-80 F, tightly sealed, out of sun; best used within a year of the date on the can\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSources\u003c\/th\u003e\n\u003ctd\u003e\n\u003ca href=\"https:\/\/generalfinishes.com\/wood-finishes-retail\/water-based-wood-stains-and-dye-stains\/water-based-wood-stain\" target=\"_blank\" rel=\"noopener\"\u003eGeneral Finishes Water-Based Wood Stain page\u003c\/a\u003e; \u003ca href=\"https:\/\/generalfinishes.com\/sites\/default\/files\/documents\/files\/2020-04\/TDS-2020-03-Water-Based-Wood-Stain-General-Finishes.pdf\" target=\"_blank\" rel=\"noopener\"\u003eTechnical data sheet (March 2020)\u003c\/a\u003e; \u003ca href=\"https:\/\/generalfinishes.com\/sites\/default\/files\/documents\/files\/2024-02\/SDS-English-Water-Based-Wood-Stain-ESPRESSO-Water-Base-General-Finishes-US-HCS-2012-v1-2024-02-02.PDF\" target=\"_blank\" rel=\"noopener\"\u003eEspresso SDS (rev. 02-Feb-2024)\u003c\/a\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\u003ch3\u003eHow much do I need?\u003c\/h3\u003e\n\u003cp\u003eGF rates the stain at up to 600 sq ft per gallon, so this pint covers up to about 75 sq ft (calculated). Porous or softer woods take more. If you plan a second coat, count it as another full pass.\u003c\/p\u003e\n\u003ch3\u003eHow to apply\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eRaw wood: sand with 120 grit, then 150 or 220 grit, and remove the dust. GF says no finer than 220 on closed-grain woods or 180 on open-grain woods. To reduce grain raise, wet the wood with water, let it dry and sand smooth before staining.\u003c\/li\u003e\n\u003cli\u003eExisting finish: scuff-clean with a non-woven pad and a 50:50 mix of denatured alcohol and water, dry 1-2 hours, then sand lightly with a 220-320 grit sponge. Remove dust and test adhesion.\u003c\/li\u003e\n\u003cli\u003eWork in a ventilated area and stir before and during use. On raw wood, apply a liberal amount to one section at a time, then wipe off the excess with the grain using absorbent terry cloth or paper towel. Do not use cotton T-shirts; they push the stain around. Correct lap marks right away by rewetting the whole section and wiping again.\u003c\/li\u003e\n\u003cli\u003eOver an existing finish, use thin coats with a foam brush or staining pad and avoid heavy build.\u003c\/li\u003e\n\u003cli\u003eLet it dry at least 2 hours (24 hours under an oil-based topcoat), then apply 3 coats of a GF topcoat. Take care not to sand through the first topcoat coat.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eGood to know\u003c\/h3\u003e\n\u003cp\u003eStain color changes with wood species, prep, lighting and the topcoat, so test the full stain-and-topcoat process on scrap first. On blotch-prone woods like pine, GF Water-Based Pre-Stain Conditioner Natural evens out color but limits how much stain soaks in, so a darker color may be needed. GF notes that California users who add more than 2% GF Extender make the stain non-compliant under SCAQMD rules. The Espresso SDS (rev. 02-Feb-2024) lists the mixture as not classified, with no signal word. Use the respirator GF specifies when spraying. Store between 50 and 80 F and do not pour leftovers down the drain.\u003c\/p\u003e\n\u003ch3\u003eQuestions\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eCan I use it over a finished cabinet?\u003c\/strong\u003e Yes, after cleaning, scuff-sanding and an adhesion test, using thin coats like a gel stain.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCan I put an oil-based polyurethane over it?\u003c\/strong\u003e Yes. GF says to let the stain dry 24 hours first. Oil-based topcoats can amber, so test the look.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDoes it need a topcoat?\u003c\/strong\u003e Yes. GF says the stain provides color but is not durable on its own; finish with 3 coats of a GF topcoat.\u003c\/p\u003e\n\u003ch3\u003eShop related\u003c\/h3\u003e\n\u003cp\u003eSame color, other size: \u003ca href=\"\/products\/general-finishes-water-based-stain-espresso-quart\"\u003eEspresso Quart\u003c\/a\u003e. Other colors in this size: \u003ca href=\"\/products\/general-finishes-water-based-stain-antique-brown-pint\"\u003eAntique Brown\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-black-pint\"\u003eBlack\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-graystone-pint\"\u003eGraystone\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-walnut-pint\"\u003eWalnut\u003c\/a\u003e. Even out pine with \u003ca href=\"\/products\/general-finishes-pre-stain-conditioner-natural-pint\"\u003eGF Water-Based Pre-Stain Conditioner Natural\u003c\/a\u003e. Topcoat with \u003ca href=\"\/products\/general-finishes-high-performance-water-based-topcoat-clear-satin-quart\"\u003eGF High Performance Topcoat, Satin\u003c\/a\u003e or see all sheens in \u003ca href=\"\/collections\/general-finishes-high-performance\"\u003eHigh Performance Topcoat\u003c\/a\u003e. Prep with a \u003ca href=\"\/products\/3m-softback-contour-sanding-sponge-fine-4-1-2-inch\"\u003e3M Softback sanding sponge\u003c\/a\u003e. Browse every color in \u003ca href=\"\/collections\/general-finishes-water-based-wood-stain\"\u003eGF Water-Based Wood Stain\u003c\/a\u003e, compare \u003ca href=\"\/collections\/curated-wood-stains-gel-stains\"\u003ewood stains and gel stains\u003c\/a\u003e, or plan the job with the \u003ca href=\"\/pages\/furniture-refinishing-project-cart\"\u003efurniture refinishing project cart\u003c\/a\u003e or \u003ca href=\"\/pages\/paint-cabinets-project-cart\"\u003ecabinet project cart\u003c\/a\u003e.\u003c\/p\u003e","brand":"General Finishes","offers":[{"title":"Default Title","offer_id":67673251086646,"sku":"WXPT","price":25.16,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0931\/9750\/0726\/files\/606016102327.jpg?v=1791582014"},{"product_id":"general-finishes-water-based-stain-espresso-quart","title":"General Finishes Water-Based Stain, Espresso, Quart","description":"\u003cp\u003eGeneral Finishes Water-Based Wood Stain in Espresso is a water-based pigmented stain for interior raw wood such as cabinets, trim, doors and furniture. General Finishes says its pigments give rich, dark, uniform color on hard-to-stain woods like maple and pine, and that it can also go over an existing finish, much like an oil-based gel stain. It is low odor, cleans up with water and is noncombustible. This is the quart (32 fl oz) can, GF item WXQT.\u003c\/p\u003e\n\u003ch3\u003eHighlights\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eOne coat is recommended; a second coat after the first is fully dry makes the color darker. GF says not to go past two coats.\u003c\/li\u003e\n\u003cli\u003eDry to the touch in 30 minutes; ready for a second coat or a water-based topcoat in 2 hours (70 F, 50% humidity). Wait 24 hours before an oil-based topcoat.\u003c\/li\u003e\n\u003cli\u003eBrush, foam brush, pad, microfiber roller or spray (HVLP 1.1-1.3 mm).\u003c\/li\u003e\n\u003cli\u003eStain gives color only; finish with 3 coats of a GF topcoat.\u003c\/li\u003e\n\u003cli\u003eThin with distilled water, starting at 5% and up to 10% by volume.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eBest for\u003c\/h3\u003e\n\u003cp\u003eIndoor cabinets, furniture, trim and doors, on raw wood or on a cleaned and scuff-sanded existing finish after an adhesion test. It is an interior stain; for outdoor wood, GF makes a separate Exterior 450 stain.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003eColor \/ size\u003c\/th\u003e\n\u003ctd\u003eEspresso \/ Quart (32 fl oz)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eGF item \/ UPC\u003c\/th\u003e\n\u003ctd\u003eWXQT \/ 606016102310\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eType\u003c\/th\u003e\n\u003ctd\u003eWater-based pigmented stain, interior\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoverage\u003c\/th\u003e\n\u003ctd\u003eUp to 600 sq ft per gallon (TDS), so up to about 150 sq ft for this can (calculated)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDry times\u003c\/th\u003e\n\u003ctd\u003eTouch 30 minutes; recoat 2 hours; 24 hours before an oil-based topcoat (70 F, 50% humidity; cool, humid or thick coats take longer)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoats\u003c\/th\u003e\n\u003ctd\u003e1 recommended, 2 maximum\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply with\u003c\/th\u003e\n\u003ctd\u003eSynthetic-bristle or foam brush, pad applicator, short-nap or foam roller, or spray. HVLP 1.1-1.3 mm; air-assist airless .007 in; airless fine finish .007-.009 in\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply when\u003c\/th\u003e\n\u003ctd\u003eAbout 70 F and 50% humidity, out of direct sun. GF Accelerator helps in cool or humid conditions, GF Extender in warm or dry ones.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThinning\u003c\/th\u003e\n\u003ctd\u003eDistilled water, 5% up to 10% by volume\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eClean up\u003c\/th\u003e\n\u003ctd\u003eSoap and water (hands); GF Brush \u0026amp; Gun Cleaner (equipment)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSolids\u003c\/th\u003e\n\u003ctd\u003e12-22% by volume, 14-20% by weight (varies by color)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVOC\u003c\/th\u003e\n\u003ctd\u003e160 g\/L on the Espresso SDS; the TDS says all colors are under 185 g\/L\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAir quality\u003c\/th\u003e\n\u003ctd\u003eSCAQMD, CARB, Canada, OTC Phase I and II compliant (TDS)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStorage\u003c\/th\u003e\n\u003ctd\u003e50-80 F, tightly sealed, out of sun; best used within a year of the date on the can\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSources\u003c\/th\u003e\n\u003ctd\u003e\n\u003ca href=\"https:\/\/generalfinishes.com\/wood-finishes-retail\/water-based-wood-stains-and-dye-stains\/water-based-wood-stain\" target=\"_blank\" rel=\"noopener\"\u003eGeneral Finishes Water-Based Wood Stain page\u003c\/a\u003e; \u003ca href=\"https:\/\/generalfinishes.com\/sites\/default\/files\/documents\/files\/2020-04\/TDS-2020-03-Water-Based-Wood-Stain-General-Finishes.pdf\" target=\"_blank\" rel=\"noopener\"\u003eTechnical data sheet (March 2020)\u003c\/a\u003e; \u003ca href=\"https:\/\/generalfinishes.com\/sites\/default\/files\/documents\/files\/2024-02\/SDS-English-Water-Based-Wood-Stain-ESPRESSO-Water-Base-General-Finishes-US-HCS-2012-v1-2024-02-02.PDF\" target=\"_blank\" rel=\"noopener\"\u003eEspresso SDS (rev. 02-Feb-2024)\u003c\/a\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\u003ch3\u003eHow much do I need?\u003c\/h3\u003e\n\u003cp\u003eGF rates the stain at up to 600 sq ft per gallon, so this quart covers up to about 150 sq ft (calculated). Porous or softer woods take more. If you plan a second coat, count it as another full pass.\u003c\/p\u003e\n\u003ch3\u003eHow to apply\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eRaw wood: sand with 120 grit, then 150 or 220 grit, and remove the dust. GF says no finer than 220 on closed-grain woods or 180 on open-grain woods. To reduce grain raise, wet the wood with water, let it dry and sand smooth before staining.\u003c\/li\u003e\n\u003cli\u003eExisting finish: scuff-clean with a non-woven pad and a 50:50 mix of denatured alcohol and water, dry 1-2 hours, then sand lightly with a 220-320 grit sponge. Remove dust and test adhesion.\u003c\/li\u003e\n\u003cli\u003eWork in a ventilated area and stir before and during use. On raw wood, apply a liberal amount to one section at a time, then wipe off the excess with the grain using absorbent terry cloth or paper towel. Do not use cotton T-shirts; they push the stain around. Correct lap marks right away by rewetting the whole section and wiping again.\u003c\/li\u003e\n\u003cli\u003eOver an existing finish, use thin coats with a foam brush or staining pad and avoid heavy build.\u003c\/li\u003e\n\u003cli\u003eLet it dry at least 2 hours (24 hours under an oil-based topcoat), then apply 3 coats of a GF topcoat. Take care not to sand through the first topcoat coat.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eGood to know\u003c\/h3\u003e\n\u003cp\u003eStain color changes with wood species, prep, lighting and the topcoat, so test the full stain-and-topcoat process on scrap first. On blotch-prone woods like pine, GF Water-Based Pre-Stain Conditioner Natural evens out color but limits how much stain soaks in, so a darker color may be needed. GF notes that California users who add more than 2% GF Extender make the stain non-compliant under SCAQMD rules. The Espresso SDS (rev. 02-Feb-2024) lists the mixture as not classified, with no signal word. Use the respirator GF specifies when spraying. Store between 50 and 80 F and do not pour leftovers down the drain.\u003c\/p\u003e\n\u003ch3\u003eQuestions\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eCan I use it over a finished cabinet?\u003c\/strong\u003e Yes, after cleaning, scuff-sanding and an adhesion test, using thin coats like a gel stain.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCan I put an oil-based polyurethane over it?\u003c\/strong\u003e Yes. GF says to let the stain dry 24 hours first. Oil-based topcoats can amber, so test the look.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDoes it need a topcoat?\u003c\/strong\u003e Yes. GF says the stain provides color but is not durable on its own; finish with 3 coats of a GF topcoat.\u003c\/p\u003e\n\u003ch3\u003eShop related\u003c\/h3\u003e\n\u003cp\u003eSame color, other size: \u003ca href=\"\/products\/general-finishes-water-based-stain-espresso-pint\"\u003eEspresso Pint\u003c\/a\u003e. Other colors in this size: \u003ca href=\"\/products\/general-finishes-water-based-stain-antique-brown-quart\"\u003eAntique Brown\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-black-quart\"\u003eBlack\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-graystone-quart\"\u003eGraystone\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-walnut-quart\"\u003eWalnut\u003c\/a\u003e. Even out pine with \u003ca href=\"\/products\/general-finishes-pre-stain-conditioner-natural-quart\"\u003eGF Water-Based Pre-Stain Conditioner Natural\u003c\/a\u003e. Topcoat with \u003ca href=\"\/products\/general-finishes-high-performance-water-based-topcoat-clear-satin-quart\"\u003eGF High Performance Topcoat, Satin\u003c\/a\u003e or see all sheens in \u003ca href=\"\/collections\/general-finishes-high-performance\"\u003eHigh Performance Topcoat\u003c\/a\u003e. Prep with a \u003ca href=\"\/products\/3m-softback-contour-sanding-sponge-fine-4-1-2-inch\"\u003e3M Softback sanding sponge\u003c\/a\u003e. Browse every color in \u003ca href=\"\/collections\/general-finishes-water-based-wood-stain\"\u003eGF Water-Based Wood Stain\u003c\/a\u003e, compare \u003ca href=\"\/collections\/curated-wood-stains-gel-stains\"\u003ewood stains and gel stains\u003c\/a\u003e, or plan the job with the \u003ca href=\"\/pages\/furniture-refinishing-project-cart\"\u003efurniture refinishing project cart\u003c\/a\u003e or \u003ca href=\"\/pages\/paint-cabinets-project-cart\"\u003ecabinet project cart\u003c\/a\u003e.\u003c\/p\u003e","brand":"General Finishes","offers":[{"title":"Default Title","offer_id":67673251283254,"sku":"WXQT","price":39.46,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0931\/9750\/0726\/files\/606016102310.jpg?v=1791582016"},{"product_id":"general-finishes-water-based-stain-pecan-pint","title":"General Finishes Water-Based Stain, Pecan, Pint","description":"\u003cp\u003eGeneral Finishes Water-Based Wood Stain in Pecan is a water-based pigmented stain for interior raw wood such as cabinets, trim, doors and furniture. General Finishes says its pigments give rich, dark, uniform color on hard-to-stain woods like maple and pine, and that it can also go over an existing finish, much like an oil-based gel stain. It is low odor, cleans up with water and is noncombustible. This is the pint (16 fl oz) can, GF item WPPT.\u003c\/p\u003e\n\u003ch3\u003eHighlights\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eOne coat is recommended; a second coat after the first is fully dry makes the color darker. GF says not to go past two coats.\u003c\/li\u003e\n\u003cli\u003eDry to the touch in 30 minutes; ready for a second coat or a water-based topcoat in 2 hours (70 F, 50% humidity). Wait 24 hours before an oil-based topcoat.\u003c\/li\u003e\n\u003cli\u003eBrush, foam brush, pad, microfiber roller or spray (HVLP 1.1-1.3 mm).\u003c\/li\u003e\n\u003cli\u003eStain gives color only; finish with 3 coats of a GF topcoat.\u003c\/li\u003e\n\u003cli\u003eThin with distilled water, starting at 5% and up to 10% by volume.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eBest for\u003c\/h3\u003e\n\u003cp\u003eIndoor cabinets, furniture, trim and doors, on raw wood or on a cleaned and scuff-sanded existing finish after an adhesion test. It is an interior stain; for outdoor wood, GF makes a separate Exterior 450 stain.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003eColor \/ size\u003c\/th\u003e\n\u003ctd\u003ePecan \/ Pint (16 fl oz)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eGF item \/ UPC\u003c\/th\u003e\n\u003ctd\u003eWPPT \/ 606016100095\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eType\u003c\/th\u003e\n\u003ctd\u003eWater-based pigmented stain, interior\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoverage\u003c\/th\u003e\n\u003ctd\u003eUp to 600 sq ft per gallon (TDS), so up to about 75 sq ft for this can (calculated)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDry times\u003c\/th\u003e\n\u003ctd\u003eTouch 30 minutes; recoat 2 hours; 24 hours before an oil-based topcoat (70 F, 50% humidity; cool, humid or thick coats take longer)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoats\u003c\/th\u003e\n\u003ctd\u003e1 recommended, 2 maximum\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply with\u003c\/th\u003e\n\u003ctd\u003eSynthetic-bristle or foam brush, pad applicator, short-nap or foam roller, or spray. HVLP 1.1-1.3 mm; air-assist airless .007 in; airless fine finish .007-.009 in\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply when\u003c\/th\u003e\n\u003ctd\u003eAbout 70 F and 50% humidity, out of direct sun. GF Accelerator helps in cool or humid conditions, GF Extender in warm or dry ones.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThinning\u003c\/th\u003e\n\u003ctd\u003eDistilled water, 5% up to 10% by volume\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eClean up\u003c\/th\u003e\n\u003ctd\u003eSoap and water (hands); GF Brush \u0026amp; Gun Cleaner (equipment)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSolids\u003c\/th\u003e\n\u003ctd\u003e12-22% by volume, 14-20% by weight (varies by color)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVOC\u003c\/th\u003e\n\u003ctd\u003eUnder 150 g\/L on the Pecan SDS (rev. 02-Feb-2024); the TDS says all colors are under 185 g\/L\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAir quality\u003c\/th\u003e\n\u003ctd\u003eSCAQMD, CARB, Canada, OTC Phase I and II compliant (TDS)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStorage\u003c\/th\u003e\n\u003ctd\u003e50-80 F, tightly sealed, out of sun; best used within a year of the date on the can\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSources\u003c\/th\u003e\n\u003ctd\u003e\n\u003ca href=\"https:\/\/generalfinishes.com\/wood-finishes-retail\/water-based-wood-stains-and-dye-stains\/water-based-wood-stain\" target=\"_blank\" rel=\"noopener\"\u003eGeneral Finishes Water-Based Wood Stain page\u003c\/a\u003e; \u003ca href=\"https:\/\/generalfinishes.com\/sites\/default\/files\/documents\/files\/2020-04\/TDS-2020-03-Water-Based-Wood-Stain-General-Finishes.pdf\" target=\"_blank\" rel=\"noopener\"\u003eTechnical data sheet (March 2020)\u003c\/a\u003e; \u003ca href=\"https:\/\/generalfinishes.com\/sites\/default\/files\/documents\/files\/2024-02\/SDS-English-Water-Based-Wood-Stain-PECAN-Water-Base-General-Finishes-US-HCS-2012-v1-2024-02-02.PDF\" target=\"_blank\" rel=\"noopener\"\u003ePecan SDS (rev. 02-Feb-2024)\u003c\/a\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\u003ch3\u003eHow much do I need?\u003c\/h3\u003e\n\u003cp\u003eGF rates the stain at up to 600 sq ft per gallon, so this pint covers up to about 75 sq ft (calculated). Porous or softer woods take more. If you plan a second coat, count it as another full pass.\u003c\/p\u003e\n\u003ch3\u003eHow to apply\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eRaw wood: sand with 120 grit, then 150 or 220 grit, and remove the dust. GF says no finer than 220 on closed-grain woods or 180 on open-grain woods. To reduce grain raise, wet the wood with water, let it dry and sand smooth before staining.\u003c\/li\u003e\n\u003cli\u003eExisting finish: scuff-clean with a non-woven pad and a 50:50 mix of denatured alcohol and water, dry 1-2 hours, then sand lightly with a 220-320 grit sponge. Remove dust and test adhesion.\u003c\/li\u003e\n\u003cli\u003eWork in a ventilated area and stir before and during use. On raw wood, apply a liberal amount to one section at a time, then wipe off the excess with the grain using absorbent terry cloth or paper towel. Do not use cotton T-shirts; they push the stain around. Correct lap marks right away by rewetting the whole section and wiping again.\u003c\/li\u003e\n\u003cli\u003eOver an existing finish, use thin coats with a foam brush or staining pad and avoid heavy build.\u003c\/li\u003e\n\u003cli\u003eLet it dry at least 2 hours (24 hours under an oil-based topcoat), then apply 3 coats of a GF topcoat. Take care not to sand through the first topcoat coat.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eGood to know\u003c\/h3\u003e\n\u003cp\u003eStain color changes with wood species, prep, lighting and the topcoat, so test the full stain-and-topcoat process on scrap first. On blotch-prone woods like pine, GF Water-Based Pre-Stain Conditioner Natural evens out color but limits how much stain soaks in, so a darker color may be needed. GF notes that California users who add more than 2% GF Extender make the stain non-compliant under SCAQMD rules. The Pecan SDS (rev. 02-Feb-2024) uses the signal word Danger: may cause cancer. Wear the protection it lists, and use the respirator GF specifies when spraying. Store between 50 and 80 F and do not pour leftovers down the drain.\u003c\/p\u003e\n\u003ch3\u003eQuestions\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eCan I use it over a finished cabinet?\u003c\/strong\u003e Yes, after cleaning, scuff-sanding and an adhesion test, using thin coats like a gel stain.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCan I put an oil-based polyurethane over it?\u003c\/strong\u003e Yes. GF says to let the stain dry 24 hours first. Oil-based topcoats can amber, so test the look.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDoes it need a topcoat?\u003c\/strong\u003e Yes. GF says the stain provides color but is not durable on its own; finish with 3 coats of a GF topcoat.\u003c\/p\u003e\n\u003ch3\u003eShop related\u003c\/h3\u003e\n\u003cp\u003eSame color, other size: \u003ca href=\"\/products\/general-finishes-water-based-stain-pecan-quart\"\u003ePecan Quart\u003c\/a\u003e. Other colors in this size: \u003ca href=\"\/products\/general-finishes-water-based-stain-antique-brown-pint\"\u003eAntique Brown\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-antique-oak-pint\"\u003eAntique Oak\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-black-pint\"\u003eBlack\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-black-cherry-pint\"\u003eBlack Cherry\u003c\/a\u003e. Even out pine with \u003ca href=\"\/products\/general-finishes-pre-stain-conditioner-natural-pint\"\u003eGF Water-Based Pre-Stain Conditioner Natural\u003c\/a\u003e. Topcoat with \u003ca href=\"\/products\/general-finishes-high-performance-water-based-topcoat-clear-satin-quart\"\u003eGF High Performance Topcoat, Satin\u003c\/a\u003e or see all sheens in \u003ca href=\"\/collections\/general-finishes-high-performance\"\u003eHigh Performance Topcoat\u003c\/a\u003e. Prep with a \u003ca href=\"\/products\/3m-softback-contour-sanding-sponge-fine-4-1-2-inch\"\u003e3M Softback sanding sponge\u003c\/a\u003e. Browse every color in \u003ca href=\"\/collections\/general-finishes-water-based-wood-stain\"\u003eGF Water-Based Wood Stain\u003c\/a\u003e, compare \u003ca href=\"\/collections\/curated-wood-stains-gel-stains\"\u003ewood stains and gel stains\u003c\/a\u003e, or plan the job with the \u003ca href=\"\/pages\/furniture-refinishing-project-cart\"\u003efurniture refinishing project cart\u003c\/a\u003e or \u003ca href=\"\/pages\/paint-cabinets-project-cart\"\u003ecabinet project cart\u003c\/a\u003e.\u003c\/p\u003e","brand":"General Finishes","offers":[{"title":"Default Title","offer_id":67673251774774,"sku":"WPPT","price":25.16,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0931\/9750\/0726\/files\/606016100095.jpg?v=1791582022"},{"product_id":"general-finishes-water-based-stain-pecan-quart","title":"General Finishes Water-Based Stain, Pecan, Quart","description":"\u003cp\u003eGeneral Finishes Water-Based Wood Stain in Pecan is a water-based pigmented stain for interior raw wood such as cabinets, trim, doors and furniture. General Finishes says its pigments give rich, dark, uniform color on hard-to-stain woods like maple and pine, and that it can also go over an existing finish, much like an oil-based gel stain. It is low odor, cleans up with water and is noncombustible. This is the quart (32 fl oz) can, GF item WPQT.\u003c\/p\u003e\n\u003ch3\u003eHighlights\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eOne coat is recommended; a second coat after the first is fully dry makes the color darker. GF says not to go past two coats.\u003c\/li\u003e\n\u003cli\u003eDry to the touch in 30 minutes; ready for a second coat or a water-based topcoat in 2 hours (70 F, 50% humidity). Wait 24 hours before an oil-based topcoat.\u003c\/li\u003e\n\u003cli\u003eBrush, foam brush, pad, microfiber roller or spray (HVLP 1.1-1.3 mm).\u003c\/li\u003e\n\u003cli\u003eStain gives color only; finish with 3 coats of a GF topcoat.\u003c\/li\u003e\n\u003cli\u003eThin with distilled water, starting at 5% and up to 10% by volume.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eBest for\u003c\/h3\u003e\n\u003cp\u003eIndoor cabinets, furniture, trim and doors, on raw wood or on a cleaned and scuff-sanded existing finish after an adhesion test. It is an interior stain; for outdoor wood, GF makes a separate Exterior 450 stain.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003eColor \/ size\u003c\/th\u003e\n\u003ctd\u003ePecan \/ Quart (32 fl oz)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eGF item \/ UPC\u003c\/th\u003e\n\u003ctd\u003eWPQT \/ 606016100262\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eType\u003c\/th\u003e\n\u003ctd\u003eWater-based pigmented stain, interior\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoverage\u003c\/th\u003e\n\u003ctd\u003eUp to 600 sq ft per gallon (TDS), so up to about 150 sq ft for this can (calculated)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDry times\u003c\/th\u003e\n\u003ctd\u003eTouch 30 minutes; recoat 2 hours; 24 hours before an oil-based topcoat (70 F, 50% humidity; cool, humid or thick coats take longer)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoats\u003c\/th\u003e\n\u003ctd\u003e1 recommended, 2 maximum\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply with\u003c\/th\u003e\n\u003ctd\u003eSynthetic-bristle or foam brush, pad applicator, short-nap or foam roller, or spray. HVLP 1.1-1.3 mm; air-assist airless .007 in; airless fine finish .007-.009 in\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply when\u003c\/th\u003e\n\u003ctd\u003eAbout 70 F and 50% humidity, out of direct sun. GF Accelerator helps in cool or humid conditions, GF Extender in warm or dry ones.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThinning\u003c\/th\u003e\n\u003ctd\u003eDistilled water, 5% up to 10% by volume\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eClean up\u003c\/th\u003e\n\u003ctd\u003eSoap and water (hands); GF Brush \u0026amp; Gun Cleaner (equipment)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSolids\u003c\/th\u003e\n\u003ctd\u003e12-22% by volume, 14-20% by weight (varies by color)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVOC\u003c\/th\u003e\n\u003ctd\u003eUnder 150 g\/L on the Pecan SDS (rev. 02-Feb-2024); the TDS says all colors are under 185 g\/L\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAir quality\u003c\/th\u003e\n\u003ctd\u003eSCAQMD, CARB, Canada, OTC Phase I and II compliant (TDS)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStorage\u003c\/th\u003e\n\u003ctd\u003e50-80 F, tightly sealed, out of sun; best used within a year of the date on the can\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSources\u003c\/th\u003e\n\u003ctd\u003e\n\u003ca href=\"https:\/\/generalfinishes.com\/wood-finishes-retail\/water-based-wood-stains-and-dye-stains\/water-based-wood-stain\" target=\"_blank\" rel=\"noopener\"\u003eGeneral Finishes Water-Based Wood Stain page\u003c\/a\u003e; \u003ca href=\"https:\/\/generalfinishes.com\/sites\/default\/files\/documents\/files\/2020-04\/TDS-2020-03-Water-Based-Wood-Stain-General-Finishes.pdf\" target=\"_blank\" rel=\"noopener\"\u003eTechnical data sheet (March 2020)\u003c\/a\u003e; \u003ca href=\"https:\/\/generalfinishes.com\/sites\/default\/files\/documents\/files\/2024-02\/SDS-English-Water-Based-Wood-Stain-PECAN-Water-Base-General-Finishes-US-HCS-2012-v1-2024-02-02.PDF\" target=\"_blank\" rel=\"noopener\"\u003ePecan SDS (rev. 02-Feb-2024)\u003c\/a\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\u003ch3\u003eHow much do I need?\u003c\/h3\u003e\n\u003cp\u003eGF rates the stain at up to 600 sq ft per gallon, so this quart covers up to about 150 sq ft (calculated). Porous or softer woods take more. If you plan a second coat, count it as another full pass.\u003c\/p\u003e\n\u003ch3\u003eHow to apply\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eRaw wood: sand with 120 grit, then 150 or 220 grit, and remove the dust. GF says no finer than 220 on closed-grain woods or 180 on open-grain woods. To reduce grain raise, wet the wood with water, let it dry and sand smooth before staining.\u003c\/li\u003e\n\u003cli\u003eExisting finish: scuff-clean with a non-woven pad and a 50:50 mix of denatured alcohol and water, dry 1-2 hours, then sand lightly with a 220-320 grit sponge. Remove dust and test adhesion.\u003c\/li\u003e\n\u003cli\u003eWork in a ventilated area and stir before and during use. On raw wood, apply a liberal amount to one section at a time, then wipe off the excess with the grain using absorbent terry cloth or paper towel. Do not use cotton T-shirts; they push the stain around. Correct lap marks right away by rewetting the whole section and wiping again.\u003c\/li\u003e\n\u003cli\u003eOver an existing finish, use thin coats with a foam brush or staining pad and avoid heavy build.\u003c\/li\u003e\n\u003cli\u003eLet it dry at least 2 hours (24 hours under an oil-based topcoat), then apply 3 coats of a GF topcoat. Take care not to sand through the first topcoat coat.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eGood to know\u003c\/h3\u003e\n\u003cp\u003eStain color changes with wood species, prep, lighting and the topcoat, so test the full stain-and-topcoat process on scrap first. On blotch-prone woods like pine, GF Water-Based Pre-Stain Conditioner Natural evens out color but limits how much stain soaks in, so a darker color may be needed. GF notes that California users who add more than 2% GF Extender make the stain non-compliant under SCAQMD rules. The Pecan SDS (rev. 02-Feb-2024) uses the signal word Danger: may cause cancer. Wear the protection it lists, and use the respirator GF specifies when spraying. Store between 50 and 80 F and do not pour leftovers down the drain.\u003c\/p\u003e\n\u003ch3\u003eQuestions\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eCan I use it over a finished cabinet?\u003c\/strong\u003e Yes, after cleaning, scuff-sanding and an adhesion test, using thin coats like a gel stain.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCan I put an oil-based polyurethane over it?\u003c\/strong\u003e Yes. GF says to let the stain dry 24 hours first. Oil-based topcoats can amber, so test the look.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDoes it need a topcoat?\u003c\/strong\u003e Yes. GF says the stain provides color but is not durable on its own; finish with 3 coats of a GF topcoat.\u003c\/p\u003e\n\u003ch3\u003eShop related\u003c\/h3\u003e\n\u003cp\u003eSame color, other size: \u003ca href=\"\/products\/general-finishes-water-based-stain-pecan-pint\"\u003ePecan Pint\u003c\/a\u003e. Other colors in this size: \u003ca href=\"\/products\/general-finishes-water-based-stain-antique-brown-quart\"\u003eAntique Brown\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-antique-oak-quart\"\u003eAntique Oak\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-black-quart\"\u003eBlack\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-black-cherry-quart\"\u003eBlack Cherry\u003c\/a\u003e. Even out pine with \u003ca href=\"\/products\/general-finishes-pre-stain-conditioner-natural-quart\"\u003eGF Water-Based Pre-Stain Conditioner Natural\u003c\/a\u003e. Topcoat with \u003ca href=\"\/products\/general-finishes-high-performance-water-based-topcoat-clear-satin-quart\"\u003eGF High Performance Topcoat, Satin\u003c\/a\u003e or see all sheens in \u003ca href=\"\/collections\/general-finishes-high-performance\"\u003eHigh Performance Topcoat\u003c\/a\u003e. Prep with a \u003ca href=\"\/products\/3m-softback-contour-sanding-sponge-fine-4-1-2-inch\"\u003e3M Softback sanding sponge\u003c\/a\u003e. Browse every color in \u003ca href=\"\/collections\/general-finishes-water-based-wood-stain\"\u003eGF Water-Based Wood Stain\u003c\/a\u003e, compare \u003ca href=\"\/collections\/curated-wood-stains-gel-stains\"\u003ewood stains and gel stains\u003c\/a\u003e, or plan the job with the \u003ca href=\"\/pages\/furniture-refinishing-project-cart\"\u003efurniture refinishing project cart\u003c\/a\u003e or \u003ca href=\"\/pages\/paint-cabinets-project-cart\"\u003ecabinet project cart\u003c\/a\u003e.\u003c\/p\u003e","brand":"General Finishes","offers":[{"title":"Default Title","offer_id":67673251807542,"sku":"WPQT","price":39.46,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0931\/9750\/0726\/files\/606016100262.jpg?v=1791582024"},{"product_id":"general-finishes-water-based-stain-walnut-pint","title":"General Finishes Water-Based Stain, Walnut, Pint","description":"\u003cp\u003eGeneral Finishes Water-Based Wood Stain in Walnut is a water-based pigmented stain for interior raw wood such as cabinets, trim, doors and furniture. General Finishes says its pigments give rich, dark, uniform color on hard-to-stain woods like maple and pine, and that it can also go over an existing finish, much like an oil-based gel stain. It is low odor, cleans up with water and is noncombustible. This is the pint (16 fl oz) can, GF item WWPT.\u003c\/p\u003e\n\u003ch3\u003eHighlights\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eOne coat is recommended; a second coat after the first is fully dry makes the color darker. GF says not to go past two coats.\u003c\/li\u003e\n\u003cli\u003eDry to the touch in 30 minutes; ready for a second coat or a water-based topcoat in 2 hours (70 F, 50% humidity). Wait 24 hours before an oil-based topcoat.\u003c\/li\u003e\n\u003cli\u003eBrush, foam brush, pad, microfiber roller or spray (HVLP 1.1-1.3 mm).\u003c\/li\u003e\n\u003cli\u003eStain gives color only; finish with 3 coats of a GF topcoat.\u003c\/li\u003e\n\u003cli\u003eThin with distilled water, starting at 5% and up to 10% by volume.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eBest for\u003c\/h3\u003e\n\u003cp\u003eIndoor cabinets, furniture, trim and doors, on raw wood or on a cleaned and scuff-sanded existing finish after an adhesion test. It is an interior stain; for outdoor wood, GF makes a separate Exterior 450 stain.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003eColor \/ size\u003c\/th\u003e\n\u003ctd\u003eWalnut \/ Pint (16 fl oz)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eGF item \/ UPC\u003c\/th\u003e\n\u003ctd\u003eWWPT \/ 606016100118\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eType\u003c\/th\u003e\n\u003ctd\u003eWater-based pigmented stain, interior\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoverage\u003c\/th\u003e\n\u003ctd\u003eUp to 600 sq ft per gallon (TDS), so up to about 75 sq ft for this can (calculated)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDry times\u003c\/th\u003e\n\u003ctd\u003eTouch 30 minutes; recoat 2 hours; 24 hours before an oil-based topcoat (70 F, 50% humidity; cool, humid or thick coats take longer)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoats\u003c\/th\u003e\n\u003ctd\u003e1 recommended, 2 maximum\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply with\u003c\/th\u003e\n\u003ctd\u003eSynthetic-bristle or foam brush, pad applicator, short-nap or foam roller, or spray. HVLP 1.1-1.3 mm; air-assist airless .007 in; airless fine finish .007-.009 in\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply when\u003c\/th\u003e\n\u003ctd\u003eAbout 70 F and 50% humidity, out of direct sun. GF Accelerator helps in cool or humid conditions, GF Extender in warm or dry ones.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThinning\u003c\/th\u003e\n\u003ctd\u003eDistilled water, 5% up to 10% by volume\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eClean up\u003c\/th\u003e\n\u003ctd\u003eSoap and water (hands); GF Brush \u0026amp; Gun Cleaner (equipment)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSolids\u003c\/th\u003e\n\u003ctd\u003e12-22% by volume, 14-20% by weight (varies by color)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVOC\u003c\/th\u003e\n\u003ctd\u003eunder 195 g\/L on the Walnut SDS (rev. 02-Feb-2024), above the \"all colors under 185 g\/L\" line on the March 2020 TDS; we show both\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAir quality\u003c\/th\u003e\n\u003ctd\u003eSCAQMD, CARB, Canada, OTC Phase I and II compliant (TDS)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStorage\u003c\/th\u003e\n\u003ctd\u003e50-80 F, tightly sealed, out of sun; best used within a year of the date on the can\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSources\u003c\/th\u003e\n\u003ctd\u003e\n\u003ca href=\"https:\/\/generalfinishes.com\/wood-finishes-retail\/water-based-wood-stains-and-dye-stains\/water-based-wood-stain\" target=\"_blank\" rel=\"noopener\"\u003eGeneral Finishes Water-Based Wood Stain page\u003c\/a\u003e; \u003ca href=\"https:\/\/generalfinishes.com\/sites\/default\/files\/documents\/files\/2020-04\/TDS-2020-03-Water-Based-Wood-Stain-General-Finishes.pdf\" target=\"_blank\" rel=\"noopener\"\u003eTechnical data sheet (March 2020)\u003c\/a\u003e; \u003ca href=\"https:\/\/generalfinishes.com\/sites\/default\/files\/documents\/files\/2024-02\/SDS-English-Water-Based-Wood-Stain-WALNUT-Water-Base-General-Finishes-US-HCS-2012-v1-2024-02-02.PDF\" target=\"_blank\" rel=\"noopener\"\u003eWalnut SDS (rev. 02-Feb-2024)\u003c\/a\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\u003ch3\u003eHow much do I need?\u003c\/h3\u003e\n\u003cp\u003eGF rates the stain at up to 600 sq ft per gallon, so this pint covers up to about 75 sq ft (calculated). Porous or softer woods take more. If you plan a second coat, count it as another full pass.\u003c\/p\u003e\n\u003ch3\u003eHow to apply\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eRaw wood: sand with 120 grit, then 150 or 220 grit, and remove the dust. GF says no finer than 220 on closed-grain woods or 180 on open-grain woods. To reduce grain raise, wet the wood with water, let it dry and sand smooth before staining.\u003c\/li\u003e\n\u003cli\u003eExisting finish: scuff-clean with a non-woven pad and a 50:50 mix of denatured alcohol and water, dry 1-2 hours, then sand lightly with a 220-320 grit sponge. Remove dust and test adhesion.\u003c\/li\u003e\n\u003cli\u003eWork in a ventilated area and stir before and during use. On raw wood, apply a liberal amount to one section at a time, then wipe off the excess with the grain using absorbent terry cloth or paper towel. Do not use cotton T-shirts; they push the stain around. Correct lap marks right away by rewetting the whole section and wiping again.\u003c\/li\u003e\n\u003cli\u003eOver an existing finish, use thin coats with a foam brush or staining pad and avoid heavy build.\u003c\/li\u003e\n\u003cli\u003eLet it dry at least 2 hours (24 hours under an oil-based topcoat), then apply 3 coats of a GF topcoat. Take care not to sand through the first topcoat coat.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eGood to know\u003c\/h3\u003e\n\u003cp\u003eStain color changes with wood species, prep, lighting and the topcoat, so test the full stain-and-topcoat process on scrap first. On blotch-prone woods like pine, GF Water-Based Pre-Stain Conditioner Natural evens out color but limits how much stain soaks in, so a darker color may be needed. GF notes that California users who add more than 2% GF Extender make the stain non-compliant under SCAQMD rules. The Walnut SDS (rev. 02-Feb-2024) uses the signal word Danger: may cause cancer. Wear the protection it lists, and use the respirator GF specifies when spraying. Store between 50 and 80 F and do not pour leftovers down the drain.\u003c\/p\u003e\n\u003ch3\u003eQuestions\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eCan I use it over a finished cabinet?\u003c\/strong\u003e Yes, after cleaning, scuff-sanding and an adhesion test, using thin coats like a gel stain.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCan I put an oil-based polyurethane over it?\u003c\/strong\u003e Yes. GF says to let the stain dry 24 hours first. Oil-based topcoats can amber, so test the look.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDoes it need a topcoat?\u003c\/strong\u003e Yes. GF says the stain provides color but is not durable on its own; finish with 3 coats of a GF topcoat.\u003c\/p\u003e\n\u003ch3\u003eShop related\u003c\/h3\u003e\n\u003cp\u003eSame color, other size: \u003ca href=\"\/products\/general-finishes-water-based-stain-walnut-quart\"\u003eWalnut Quart\u003c\/a\u003e. Other colors in this size: \u003ca href=\"\/products\/general-finishes-water-based-stain-antique-brown-pint\"\u003eAntique Brown\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-black-pint\"\u003eBlack\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-espresso-pint\"\u003eEspresso\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-graystone-pint\"\u003eGraystone\u003c\/a\u003e. Even out pine with \u003ca href=\"\/products\/general-finishes-pre-stain-conditioner-natural-pint\"\u003eGF Water-Based Pre-Stain Conditioner Natural\u003c\/a\u003e. Topcoat with \u003ca href=\"\/products\/general-finishes-high-performance-water-based-topcoat-clear-satin-quart\"\u003eGF High Performance Topcoat, Satin\u003c\/a\u003e or see all sheens in \u003ca href=\"\/collections\/general-finishes-high-performance\"\u003eHigh Performance Topcoat\u003c\/a\u003e. Prep with a \u003ca href=\"\/products\/3m-softback-contour-sanding-sponge-fine-4-1-2-inch\"\u003e3M Softback sanding sponge\u003c\/a\u003e. Browse every color in \u003ca href=\"\/collections\/general-finishes-water-based-wood-stain\"\u003eGF Water-Based Wood Stain\u003c\/a\u003e, compare \u003ca href=\"\/collections\/curated-wood-stains-gel-stains\"\u003ewood stains and gel stains\u003c\/a\u003e, or plan the job with the \u003ca href=\"\/pages\/furniture-refinishing-project-cart\"\u003efurniture refinishing project cart\u003c\/a\u003e or \u003ca href=\"\/pages\/paint-cabinets-project-cart\"\u003ecabinet project cart\u003c\/a\u003e.\u003c\/p\u003e","brand":"General Finishes","offers":[{"title":"Default Title","offer_id":67673251840310,"sku":"WWPT","price":25.16,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0931\/9750\/0726\/files\/606016100118.jpg?v=1791582026"},{"product_id":"general-finishes-water-based-stain-walnut-quart","title":"General Finishes Water-Based Stain, Walnut, Quart","description":"\u003cp\u003eGeneral Finishes Water-Based Wood Stain in Walnut is a water-based pigmented stain for interior raw wood such as cabinets, trim, doors and furniture. General Finishes says its pigments give rich, dark, uniform color on hard-to-stain woods like maple and pine, and that it can also go over an existing finish, much like an oil-based gel stain. It is low odor, cleans up with water and is noncombustible. This is the quart (32 fl oz) can, GF item WWQT.\u003c\/p\u003e\n\u003ch3\u003eHighlights\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eOne coat is recommended; a second coat after the first is fully dry makes the color darker. GF says not to go past two coats.\u003c\/li\u003e\n\u003cli\u003eDry to the touch in 30 minutes; ready for a second coat or a water-based topcoat in 2 hours (70 F, 50% humidity). Wait 24 hours before an oil-based topcoat.\u003c\/li\u003e\n\u003cli\u003eBrush, foam brush, pad, microfiber roller or spray (HVLP 1.1-1.3 mm).\u003c\/li\u003e\n\u003cli\u003eStain gives color only; finish with 3 coats of a GF topcoat.\u003c\/li\u003e\n\u003cli\u003eThin with distilled water, starting at 5% and up to 10% by volume.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eBest for\u003c\/h3\u003e\n\u003cp\u003eIndoor cabinets, furniture, trim and doors, on raw wood or on a cleaned and scuff-sanded existing finish after an adhesion test. It is an interior stain; for outdoor wood, GF makes a separate Exterior 450 stain.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003eColor \/ size\u003c\/th\u003e\n\u003ctd\u003eWalnut \/ Quart (32 fl oz)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eGF item \/ UPC\u003c\/th\u003e\n\u003ctd\u003eWWQT \/ 606016100286\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eType\u003c\/th\u003e\n\u003ctd\u003eWater-based pigmented stain, interior\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoverage\u003c\/th\u003e\n\u003ctd\u003eUp to 600 sq ft per gallon (TDS), so up to about 150 sq ft for this can (calculated)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDry times\u003c\/th\u003e\n\u003ctd\u003eTouch 30 minutes; recoat 2 hours; 24 hours before an oil-based topcoat (70 F, 50% humidity; cool, humid or thick coats take longer)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoats\u003c\/th\u003e\n\u003ctd\u003e1 recommended, 2 maximum\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply with\u003c\/th\u003e\n\u003ctd\u003eSynthetic-bristle or foam brush, pad applicator, short-nap or foam roller, or spray. HVLP 1.1-1.3 mm; air-assist airless .007 in; airless fine finish .007-.009 in\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply when\u003c\/th\u003e\n\u003ctd\u003eAbout 70 F and 50% humidity, out of direct sun. GF Accelerator helps in cool or humid conditions, GF Extender in warm or dry ones.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThinning\u003c\/th\u003e\n\u003ctd\u003eDistilled water, 5% up to 10% by volume\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eClean up\u003c\/th\u003e\n\u003ctd\u003eSoap and water (hands); GF Brush \u0026amp; Gun Cleaner (equipment)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSolids\u003c\/th\u003e\n\u003ctd\u003e12-22% by volume, 14-20% by weight (varies by color)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVOC\u003c\/th\u003e\n\u003ctd\u003eunder 195 g\/L on the Walnut SDS (rev. 02-Feb-2024), above the \"all colors under 185 g\/L\" line on the March 2020 TDS; we show both\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAir quality\u003c\/th\u003e\n\u003ctd\u003eSCAQMD, CARB, Canada, OTC Phase I and II compliant (TDS)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStorage\u003c\/th\u003e\n\u003ctd\u003e50-80 F, tightly sealed, out of sun; best used within a year of the date on the can\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSources\u003c\/th\u003e\n\u003ctd\u003e\n\u003ca href=\"https:\/\/generalfinishes.com\/wood-finishes-retail\/water-based-wood-stains-and-dye-stains\/water-based-wood-stain\" target=\"_blank\" rel=\"noopener\"\u003eGeneral Finishes Water-Based Wood Stain page\u003c\/a\u003e; \u003ca href=\"https:\/\/generalfinishes.com\/sites\/default\/files\/documents\/files\/2020-04\/TDS-2020-03-Water-Based-Wood-Stain-General-Finishes.pdf\" target=\"_blank\" rel=\"noopener\"\u003eTechnical data sheet (March 2020)\u003c\/a\u003e; \u003ca href=\"https:\/\/generalfinishes.com\/sites\/default\/files\/documents\/files\/2024-02\/SDS-English-Water-Based-Wood-Stain-WALNUT-Water-Base-General-Finishes-US-HCS-2012-v1-2024-02-02.PDF\" target=\"_blank\" rel=\"noopener\"\u003eWalnut SDS (rev. 02-Feb-2024)\u003c\/a\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\u003ch3\u003eHow much do I need?\u003c\/h3\u003e\n\u003cp\u003eGF rates the stain at up to 600 sq ft per gallon, so this quart covers up to about 150 sq ft (calculated). Porous or softer woods take more. If you plan a second coat, count it as another full pass.\u003c\/p\u003e\n\u003ch3\u003eHow to apply\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eRaw wood: sand with 120 grit, then 150 or 220 grit, and remove the dust. GF says no finer than 220 on closed-grain woods or 180 on open-grain woods. To reduce grain raise, wet the wood with water, let it dry and sand smooth before staining.\u003c\/li\u003e\n\u003cli\u003eExisting finish: scuff-clean with a non-woven pad and a 50:50 mix of denatured alcohol and water, dry 1-2 hours, then sand lightly with a 220-320 grit sponge. Remove dust and test adhesion.\u003c\/li\u003e\n\u003cli\u003eWork in a ventilated area and stir before and during use. On raw wood, apply a liberal amount to one section at a time, then wipe off the excess with the grain using absorbent terry cloth or paper towel. Do not use cotton T-shirts; they push the stain around. Correct lap marks right away by rewetting the whole section and wiping again.\u003c\/li\u003e\n\u003cli\u003eOver an existing finish, use thin coats with a foam brush or staining pad and avoid heavy build.\u003c\/li\u003e\n\u003cli\u003eLet it dry at least 2 hours (24 hours under an oil-based topcoat), then apply 3 coats of a GF topcoat. Take care not to sand through the first topcoat coat.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eGood to know\u003c\/h3\u003e\n\u003cp\u003eStain color changes with wood species, prep, lighting and the topcoat, so test the full stain-and-topcoat process on scrap first. On blotch-prone woods like pine, GF Water-Based Pre-Stain Conditioner Natural evens out color but limits how much stain soaks in, so a darker color may be needed. GF notes that California users who add more than 2% GF Extender make the stain non-compliant under SCAQMD rules. The Walnut SDS (rev. 02-Feb-2024) uses the signal word Danger: may cause cancer. Wear the protection it lists, and use the respirator GF specifies when spraying. Store between 50 and 80 F and do not pour leftovers down the drain.\u003c\/p\u003e\n\u003ch3\u003eQuestions\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eCan I use it over a finished cabinet?\u003c\/strong\u003e Yes, after cleaning, scuff-sanding and an adhesion test, using thin coats like a gel stain.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCan I put an oil-based polyurethane over it?\u003c\/strong\u003e Yes. GF says to let the stain dry 24 hours first. Oil-based topcoats can amber, so test the look.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDoes it need a topcoat?\u003c\/strong\u003e Yes. GF says the stain provides color but is not durable on its own; finish with 3 coats of a GF topcoat.\u003c\/p\u003e\n\u003ch3\u003eShop related\u003c\/h3\u003e\n\u003cp\u003eSame color, other size: \u003ca href=\"\/products\/general-finishes-water-based-stain-walnut-pint\"\u003eWalnut Pint\u003c\/a\u003e. Other colors in this size: \u003ca href=\"\/products\/general-finishes-water-based-stain-antique-brown-quart\"\u003eAntique Brown\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-black-quart\"\u003eBlack\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-espresso-quart\"\u003eEspresso\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-graystone-quart\"\u003eGraystone\u003c\/a\u003e. Even out pine with \u003ca href=\"\/products\/general-finishes-pre-stain-conditioner-natural-quart\"\u003eGF Water-Based Pre-Stain Conditioner Natural\u003c\/a\u003e. Topcoat with \u003ca href=\"\/products\/general-finishes-high-performance-water-based-topcoat-clear-satin-quart\"\u003eGF High Performance Topcoat, Satin\u003c\/a\u003e or see all sheens in \u003ca href=\"\/collections\/general-finishes-high-performance\"\u003eHigh Performance Topcoat\u003c\/a\u003e. Prep with a \u003ca href=\"\/products\/3m-softback-contour-sanding-sponge-fine-4-1-2-inch\"\u003e3M Softback sanding sponge\u003c\/a\u003e. Browse every color in \u003ca href=\"\/collections\/general-finishes-water-based-wood-stain\"\u003eGF Water-Based Wood Stain\u003c\/a\u003e, compare \u003ca href=\"\/collections\/curated-wood-stains-gel-stains\"\u003ewood stains and gel stains\u003c\/a\u003e, or plan the job with the \u003ca href=\"\/pages\/furniture-refinishing-project-cart\"\u003efurniture refinishing project cart\u003c\/a\u003e or \u003ca href=\"\/pages\/paint-cabinets-project-cart\"\u003ecabinet project cart\u003c\/a\u003e.\u003c\/p\u003e","brand":"General Finishes","offers":[{"title":"Default Title","offer_id":67673251873078,"sku":"WWQT","price":39.46,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0931\/9750\/0726\/files\/606016100286.jpg?v=1791582028"},{"product_id":"general-finishes-water-based-stain-whitewash-pint","title":"General Finishes Water-Based Stain, Whitewash, Pint","description":"\u003cp\u003eGeneral Finishes Water-Based Wood Stain in Whitewash is a water-based pigmented stain for interior raw wood such as cabinets, trim, doors and furniture. General Finishes says its pigments give rich, dark, uniform color on hard-to-stain woods like maple and pine, and that it can also go over an existing finish, much like an oil-based gel stain. It is low odor, cleans up with water and is noncombustible. This is the pint (16 fl oz) can, GF item WIPT.\u003c\/p\u003e\n\u003ch3\u003eHighlights\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eOne coat is recommended; a second coat after the first is fully dry makes the color darker. GF says not to go past two coats.\u003c\/li\u003e\n\u003cli\u003eDry to the touch in 30 minutes; ready for a second coat or a water-based topcoat in 2 hours (70 F, 50% humidity). Wait 24 hours before an oil-based topcoat.\u003c\/li\u003e\n\u003cli\u003eBrush, foam brush, pad, microfiber roller or spray (HVLP 1.1-1.3 mm).\u003c\/li\u003e\n\u003cli\u003eStain gives color only; finish with 3 coats of a GF topcoat.\u003c\/li\u003e\n\u003cli\u003eThin with distilled water, starting at 5% and up to 10% by volume.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eBest for\u003c\/h3\u003e\n\u003cp\u003eIndoor cabinets, furniture, trim and doors, on raw wood or on a cleaned and scuff-sanded existing finish after an adhesion test. It is an interior stain; for outdoor wood, GF makes a separate Exterior 450 stain.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003eColor \/ size\u003c\/th\u003e\n\u003ctd\u003eWhitewash \/ Pint (16 fl oz)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eGF item \/ UPC\u003c\/th\u003e\n\u003ctd\u003eWIPT \/ 606016100019\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eType\u003c\/th\u003e\n\u003ctd\u003eWater-based pigmented stain, interior\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoverage\u003c\/th\u003e\n\u003ctd\u003eUp to 600 sq ft per gallon (TDS), so up to about 75 sq ft for this can (calculated)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDry times\u003c\/th\u003e\n\u003ctd\u003eTouch 30 minutes; recoat 2 hours; 24 hours before an oil-based topcoat (70 F, 50% humidity; cool, humid or thick coats take longer)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoats\u003c\/th\u003e\n\u003ctd\u003e1 recommended, 2 maximum\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply with\u003c\/th\u003e\n\u003ctd\u003eSynthetic-bristle or foam brush, pad applicator, short-nap or foam roller, or spray. HVLP 1.1-1.3 mm; air-assist airless .007 in; airless fine finish .007-.009 in\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply when\u003c\/th\u003e\n\u003ctd\u003eAbout 70 F and 50% humidity, out of direct sun. GF Accelerator helps in cool or humid conditions, GF Extender in warm or dry ones.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThinning\u003c\/th\u003e\n\u003ctd\u003eDistilled water, 5% up to 10% by volume\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eClean up\u003c\/th\u003e\n\u003ctd\u003eSoap and water (hands); GF Brush \u0026amp; Gun Cleaner (equipment)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSolids\u003c\/th\u003e\n\u003ctd\u003e12-22% by volume, 14-20% by weight (varies by color)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVOC\u003c\/th\u003e\n\u003ctd\u003e150 g\/L on the Whitewash SDS; the TDS says all colors are under 185 g\/L\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAir quality\u003c\/th\u003e\n\u003ctd\u003eSCAQMD, CARB, Canada, OTC Phase I and II compliant (TDS)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStorage\u003c\/th\u003e\n\u003ctd\u003e50-80 F, tightly sealed, out of sun; best used within a year of the date on the can\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSources\u003c\/th\u003e\n\u003ctd\u003e\n\u003ca href=\"https:\/\/generalfinishes.com\/wood-finishes-retail\/water-based-wood-stains-and-dye-stains\/water-based-wood-stain\" target=\"_blank\" rel=\"noopener\"\u003eGeneral Finishes Water-Based Wood Stain page\u003c\/a\u003e; \u003ca href=\"https:\/\/generalfinishes.com\/sites\/default\/files\/documents\/files\/2020-04\/TDS-2020-03-Water-Based-Wood-Stain-General-Finishes.pdf\" target=\"_blank\" rel=\"noopener\"\u003eTechnical data sheet (March 2020)\u003c\/a\u003e; \u003ca href=\"https:\/\/generalfinishes.com\/sites\/default\/files\/documents\/files\/2024-02\/SDS-English-Water-Based-Wood-Stain-WHITEWASH-Water-Base-General-Finishes-US-HCS-2012-v1-2024-02-02.PDF\" target=\"_blank\" rel=\"noopener\"\u003eWhitewash SDS (rev. 02-Feb-2024)\u003c\/a\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\u003ch3\u003eHow much do I need?\u003c\/h3\u003e\n\u003cp\u003eGF rates the stain at up to 600 sq ft per gallon, so this pint covers up to about 75 sq ft (calculated). Porous or softer woods take more. If you plan a second coat, count it as another full pass.\u003c\/p\u003e\n\u003ch3\u003eHow to apply\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eRaw wood: sand with 120 grit, then 150 or 220 grit, and remove the dust. GF says no finer than 220 on closed-grain woods or 180 on open-grain woods. To reduce grain raise, wet the wood with water, let it dry and sand smooth before staining.\u003c\/li\u003e\n\u003cli\u003eExisting finish: scuff-clean with a non-woven pad and a 50:50 mix of denatured alcohol and water, dry 1-2 hours, then sand lightly with a 220-320 grit sponge. Remove dust and test adhesion.\u003c\/li\u003e\n\u003cli\u003eWork in a ventilated area and stir before and during use. On raw wood, apply a liberal amount to one section at a time, then wipe off the excess with the grain using absorbent terry cloth or paper towel. Do not use cotton T-shirts; they push the stain around. Correct lap marks right away by rewetting the whole section and wiping again.\u003c\/li\u003e\n\u003cli\u003eOver an existing finish, use thin coats with a foam brush or staining pad and avoid heavy build.\u003c\/li\u003e\n\u003cli\u003eLet it dry at least 2 hours (24 hours under an oil-based topcoat), then apply 3 coats of a GF topcoat. Take care not to sand through the first topcoat coat.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eGood to know\u003c\/h3\u003e\n\u003cp\u003eStain color changes with wood species, prep, lighting and the topcoat, so test the full stain-and-topcoat process on scrap first. On blotch-prone woods like pine, GF Water-Based Pre-Stain Conditioner Natural evens out color but limits how much stain soaks in, so a darker color may be needed. GF notes that California users who add more than 2% GF Extender make the stain non-compliant under SCAQMD rules. The Whitewash SDS (rev. 02-Feb-2024) uses the signal word Warning: suspected of causing cancer. Wear the protection it lists, and use the respirator GF specifies when spraying. Store between 50 and 80 F and do not pour leftovers down the drain.\u003c\/p\u003e\n\u003ch3\u003eQuestions\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eCan I use it over a finished cabinet?\u003c\/strong\u003e Yes, after cleaning, scuff-sanding and an adhesion test, using thin coats like a gel stain.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCan I put an oil-based polyurethane over it?\u003c\/strong\u003e Yes. GF says to let the stain dry 24 hours first. Oil-based topcoats can amber, so test the look.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDoes it need a topcoat?\u003c\/strong\u003e Yes. GF says the stain provides color but is not durable on its own; finish with 3 coats of a GF topcoat.\u003c\/p\u003e\n\u003ch3\u003eShop related\u003c\/h3\u003e\n\u003cp\u003eSame color, other size: \u003ca href=\"\/products\/general-finishes-water-based-stain-whitewash-quart\"\u003eWhitewash Quart\u003c\/a\u003e. Other colors in this size: \u003ca href=\"\/products\/general-finishes-water-based-stain-antique-brown-pint\"\u003eAntique Brown\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-black-pint\"\u003eBlack\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-espresso-pint\"\u003eEspresso\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-graystone-pint\"\u003eGraystone\u003c\/a\u003e. Even out pine with \u003ca href=\"\/products\/general-finishes-pre-stain-conditioner-natural-pint\"\u003eGF Water-Based Pre-Stain Conditioner Natural\u003c\/a\u003e. Topcoat with \u003ca href=\"\/products\/general-finishes-high-performance-water-based-topcoat-clear-satin-quart\"\u003eGF High Performance Topcoat, Satin\u003c\/a\u003e or see all sheens in \u003ca href=\"\/collections\/general-finishes-high-performance\"\u003eHigh Performance Topcoat\u003c\/a\u003e. Prep with a \u003ca href=\"\/products\/3m-softback-contour-sanding-sponge-fine-4-1-2-inch\"\u003e3M Softback sanding sponge\u003c\/a\u003e. Browse every color in \u003ca href=\"\/collections\/general-finishes-water-based-wood-stain\"\u003eGF Water-Based Wood Stain\u003c\/a\u003e, compare \u003ca href=\"\/collections\/curated-wood-stains-gel-stains\"\u003ewood stains and gel stains\u003c\/a\u003e, or plan the job with the \u003ca href=\"\/pages\/furniture-refinishing-project-cart\"\u003efurniture refinishing project cart\u003c\/a\u003e or \u003ca href=\"\/pages\/paint-cabinets-project-cart\"\u003ecabinet project cart\u003c\/a\u003e.\u003c\/p\u003e","brand":"General Finishes","offers":[{"title":"Default Title","offer_id":67673251905846,"sku":"WIPT","price":25.16,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0931\/9750\/0726\/files\/606016100019.jpg?v=1791582030"},{"product_id":"general-finishes-water-based-stain-whitewash-quart","title":"General Finishes Water-Based Stain, Whitewash, Quart","description":"\u003cp\u003eGeneral Finishes Water-Based Wood Stain in Whitewash is a water-based pigmented stain for interior raw wood such as cabinets, trim, doors and furniture. General Finishes says its pigments give rich, dark, uniform color on hard-to-stain woods like maple and pine, and that it can also go over an existing finish, much like an oil-based gel stain. It is low odor, cleans up with water and is noncombustible. This is the quart (32 fl oz) can, GF item WIQT.\u003c\/p\u003e\n\u003ch3\u003eHighlights\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eOne coat is recommended; a second coat after the first is fully dry makes the color darker. GF says not to go past two coats.\u003c\/li\u003e\n\u003cli\u003eDry to the touch in 30 minutes; ready for a second coat or a water-based topcoat in 2 hours (70 F, 50% humidity). Wait 24 hours before an oil-based topcoat.\u003c\/li\u003e\n\u003cli\u003eBrush, foam brush, pad, microfiber roller or spray (HVLP 1.1-1.3 mm).\u003c\/li\u003e\n\u003cli\u003eStain gives color only; finish with 3 coats of a GF topcoat.\u003c\/li\u003e\n\u003cli\u003eThin with distilled water, starting at 5% and up to 10% by volume.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eBest for\u003c\/h3\u003e\n\u003cp\u003eIndoor cabinets, furniture, trim and doors, on raw wood or on a cleaned and scuff-sanded existing finish after an adhesion test. It is an interior stain; for outdoor wood, GF makes a separate Exterior 450 stain.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003eColor \/ size\u003c\/th\u003e\n\u003ctd\u003eWhitewash \/ Quart (32 fl oz)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eGF item \/ UPC\u003c\/th\u003e\n\u003ctd\u003eWIQT \/ 606016100187\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eType\u003c\/th\u003e\n\u003ctd\u003eWater-based pigmented stain, interior\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoverage\u003c\/th\u003e\n\u003ctd\u003eUp to 600 sq ft per gallon (TDS), so up to about 150 sq ft for this can (calculated)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDry times\u003c\/th\u003e\n\u003ctd\u003eTouch 30 minutes; recoat 2 hours; 24 hours before an oil-based topcoat (70 F, 50% humidity; cool, humid or thick coats take longer)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCoats\u003c\/th\u003e\n\u003ctd\u003e1 recommended, 2 maximum\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply with\u003c\/th\u003e\n\u003ctd\u003eSynthetic-bristle or foam brush, pad applicator, short-nap or foam roller, or spray. HVLP 1.1-1.3 mm; air-assist airless .007 in; airless fine finish .007-.009 in\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApply when\u003c\/th\u003e\n\u003ctd\u003eAbout 70 F and 50% humidity, out of direct sun. GF Accelerator helps in cool or humid conditions, GF Extender in warm or dry ones.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThinning\u003c\/th\u003e\n\u003ctd\u003eDistilled water, 5% up to 10% by volume\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eClean up\u003c\/th\u003e\n\u003ctd\u003eSoap and water (hands); GF Brush \u0026amp; Gun Cleaner (equipment)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSolids\u003c\/th\u003e\n\u003ctd\u003e12-22% by volume, 14-20% by weight (varies by color)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVOC\u003c\/th\u003e\n\u003ctd\u003e150 g\/L on the Whitewash SDS; the TDS says all colors are under 185 g\/L\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAir quality\u003c\/th\u003e\n\u003ctd\u003eSCAQMD, CARB, Canada, OTC Phase I and II compliant (TDS)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStorage\u003c\/th\u003e\n\u003ctd\u003e50-80 F, tightly sealed, out of sun; best used within a year of the date on the can\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSources\u003c\/th\u003e\n\u003ctd\u003e\n\u003ca href=\"https:\/\/generalfinishes.com\/wood-finishes-retail\/water-based-wood-stains-and-dye-stains\/water-based-wood-stain\" target=\"_blank\" rel=\"noopener\"\u003eGeneral Finishes Water-Based Wood Stain page\u003c\/a\u003e; \u003ca href=\"https:\/\/generalfinishes.com\/sites\/default\/files\/documents\/files\/2020-04\/TDS-2020-03-Water-Based-Wood-Stain-General-Finishes.pdf\" target=\"_blank\" rel=\"noopener\"\u003eTechnical data sheet (March 2020)\u003c\/a\u003e; \u003ca href=\"https:\/\/generalfinishes.com\/sites\/default\/files\/documents\/files\/2024-02\/SDS-English-Water-Based-Wood-Stain-WHITEWASH-Water-Base-General-Finishes-US-HCS-2012-v1-2024-02-02.PDF\" target=\"_blank\" rel=\"noopener\"\u003eWhitewash SDS (rev. 02-Feb-2024)\u003c\/a\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\u003ch3\u003eHow much do I need?\u003c\/h3\u003e\n\u003cp\u003eGF rates the stain at up to 600 sq ft per gallon, so this quart covers up to about 150 sq ft (calculated). Porous or softer woods take more. If you plan a second coat, count it as another full pass.\u003c\/p\u003e\n\u003ch3\u003eHow to apply\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eRaw wood: sand with 120 grit, then 150 or 220 grit, and remove the dust. GF says no finer than 220 on closed-grain woods or 180 on open-grain woods. To reduce grain raise, wet the wood with water, let it dry and sand smooth before staining.\u003c\/li\u003e\n\u003cli\u003eExisting finish: scuff-clean with a non-woven pad and a 50:50 mix of denatured alcohol and water, dry 1-2 hours, then sand lightly with a 220-320 grit sponge. Remove dust and test adhesion.\u003c\/li\u003e\n\u003cli\u003eWork in a ventilated area and stir before and during use. On raw wood, apply a liberal amount to one section at a time, then wipe off the excess with the grain using absorbent terry cloth or paper towel. Do not use cotton T-shirts; they push the stain around. Correct lap marks right away by rewetting the whole section and wiping again.\u003c\/li\u003e\n\u003cli\u003eOver an existing finish, use thin coats with a foam brush or staining pad and avoid heavy build.\u003c\/li\u003e\n\u003cli\u003eLet it dry at least 2 hours (24 hours under an oil-based topcoat), then apply 3 coats of a GF topcoat. Take care not to sand through the first topcoat coat.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eGood to know\u003c\/h3\u003e\n\u003cp\u003eStain color changes with wood species, prep, lighting and the topcoat, so test the full stain-and-topcoat process on scrap first. On blotch-prone woods like pine, GF Water-Based Pre-Stain Conditioner Natural evens out color but limits how much stain soaks in, so a darker color may be needed. GF notes that California users who add more than 2% GF Extender make the stain non-compliant under SCAQMD rules. The Whitewash SDS (rev. 02-Feb-2024) uses the signal word Warning: suspected of causing cancer. Wear the protection it lists, and use the respirator GF specifies when spraying. Store between 50 and 80 F and do not pour leftovers down the drain.\u003c\/p\u003e\n\u003ch3\u003eQuestions\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eCan I use it over a finished cabinet?\u003c\/strong\u003e Yes, after cleaning, scuff-sanding and an adhesion test, using thin coats like a gel stain.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCan I put an oil-based polyurethane over it?\u003c\/strong\u003e Yes. GF says to let the stain dry 24 hours first. Oil-based topcoats can amber, so test the look.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDoes it need a topcoat?\u003c\/strong\u003e Yes. GF says the stain provides color but is not durable on its own; finish with 3 coats of a GF topcoat.\u003c\/p\u003e\n\u003ch3\u003eShop related\u003c\/h3\u003e\n\u003cp\u003eSame color, other size: \u003ca href=\"\/products\/general-finishes-water-based-stain-whitewash-pint\"\u003eWhitewash Pint\u003c\/a\u003e. Other colors in this size: \u003ca href=\"\/products\/general-finishes-water-based-stain-antique-brown-quart\"\u003eAntique Brown\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-black-quart\"\u003eBlack\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-espresso-quart\"\u003eEspresso\u003c\/a\u003e, \u003ca href=\"\/products\/general-finishes-water-based-stain-graystone-quart\"\u003eGraystone\u003c\/a\u003e. Even out pine with \u003ca href=\"\/products\/general-finishes-pre-stain-conditioner-natural-quart\"\u003eGF Water-Based Pre-Stain Conditioner Natural\u003c\/a\u003e. Topcoat with \u003ca href=\"\/products\/general-finishes-high-performance-water-based-topcoat-clear-satin-quart\"\u003eGF High Performance Topcoat, Satin\u003c\/a\u003e or see all sheens in \u003ca href=\"\/collections\/general-finishes-high-performance\"\u003eHigh Performance Topcoat\u003c\/a\u003e. Prep with a \u003ca href=\"\/products\/3m-softback-contour-sanding-sponge-fine-4-1-2-inch\"\u003e3M Softback sanding sponge\u003c\/a\u003e. Browse every color in \u003ca href=\"\/collections\/general-finishes-water-based-wood-stain\"\u003eGF Water-Based Wood Stain\u003c\/a\u003e, compare \u003ca href=\"\/collections\/curated-wood-stains-gel-stains\"\u003ewood stains and gel stains\u003c\/a\u003e, or plan the job with the \u003ca href=\"\/pages\/furniture-refinishing-project-cart\"\u003efurniture refinishing project cart\u003c\/a\u003e or \u003ca href=\"\/pages\/paint-cabinets-project-cart\"\u003ecabinet project cart\u003c\/a\u003e.\u003c\/p\u003e","brand":"General Finishes","offers":[{"title":"Default Title","offer_id":67673251971382,"sku":"WIQT","price":39.46,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0931\/9750\/0726\/files\/606016100187.jpg?v=1791582032"}],"url":"https:\/\/projectweekenddiy.com\/collections\/general-finishes-water-based-wood-stain.oembed","provider":"Project Weekend DIY","version":"1.0","type":"link"}